Dukane Projector 6860WUSS-B User Manual

							138
Stacking projectors
The	projected	image	brightness	can	be	doubled	by	gravity	stacking	up	to	two	projectors	without	external	support.	This	
is	called	“Stacking	Projection”.
2	projectors	can	be	stacked	on	top	of	each	other	for	“Stacking”	setup.
 CAUTION:
A	minimum	of	two	persons	are	required	to	carry	the	projector.	Otherwise	the	projector	may	tumble	or	drop,	causing	
personal	injury.
NOTE:
•	 Projectors	with	different	model	numbers	cannot	be	gravity	stacked.
 Optional lenses with the same model numbers must be used for stacking pr\
ojection.
•	 For	stacking	projectors,	attach	the	supplied	three	stacking	holders	to	the	top	of	the	lower	projector.	(→ next page)
•	 It	does	not	support	overlay	accuracy	by	stacked	projectors.	Precise	images	as	small	texts	and	detailed	graphics	can	not	be	clearly	
read or seen.
•	 Use	a	commercially	available	distribution	amplifier	to	both	the	primary	(upper)	and	the	secondary	(lower)	projectors	to	distribute	
signal to two outputs of the two projectors.
•	 Notes	for	stacking
-	 Ask	your	service	person	for	setting	up	and	adjusting	projectors.
-	 Set	up	the	projectors	in	a	place	or	structure	in	a	way	with	sufficient	strength	to	support	the	combined	weight	of	the	two	projec-
tors.	The	single	projector	with	a	lens	weighs	up	to	approximately	20	kg/	44	lbs.
- To prevent the projectors from falling, fasten them in a way to withstand\
 earthquakes.
-	 Double	stacking	will	cause	room	temperature	to	increase.	Ventilate	the	room	well.
-	 Do	not	attempt	to	stack	projectors	on	the	ceiling.	Gravity	stacking	cannot	be	done	on	the	ceiling.
-	 Warm	up	the	projectors	for	one	hour	before	the	desired	projection	is	obtained.
-	 Make	sure	that	the	position	of	the	upper	projector	does	not	exceed	its	specifications.	When	setting	up	the	two	projectors,	
adjustable height range for the tilt feet on the upper projector is adde\
d to the total adjustable range.
-	 Set	up	the	projectors	so	that	the	projected	image	shows	as	little	geometric	distortions	as	possible.	The	lens	is	different	in	
geometric	distortion	between	wide(+)	and	tele	(−)	for	zoom.
-	 Adjust	the	horizontal	lens	shift	to	the	lens	center. s
6. Installation and Connections  
						

							139
Attaching	Stacking	Holders
Attach	three	stacking	holders	to	three	locations	on	the	top	of	the	lower	projector.
Preparation:
Tools	required	are	Phillips	screwdriver	(plus-head)	and	three	stacking	holders	packaged	with	the	projector.
Loosen	the	tilt	feet	(three	locations)	of	the	projector.
1. Remove rubber caps and screws at three locations.
(1)	Use	your	tweezers	or	nail	to	pinch	and	pull	up	the	rubber	cap.
(2)	Remove	the	screw	from	a	square	hole.
(1)(2)
2. Attach the three stacking holders at three locations.
(1)	Place	a	stacking	holder	in	a	square	hole.
(2)	Use	the	screw	removed	at	Step	1	to	fix	the	stacking	holder	in	the	square	hole.
(3)	Put	the	rubber	cap	removed	at	Step	1	back	into	the	square	hole.
	 •	 Snap	the	tabs	on	both	of	the	rubber	cap	into	the	slits	on	both	sides	in	the	square	hole.
(1)(2)(3)
6. Installation and Connections  
						

							140
3.	 Put	another	projector	on	the	first	projector.
	 Put	each	tilt	foot	of	the	upper	projector	on	the	stacking	holders	(three	locations).
•	 Each	tilt	foot	has	a	rubber.	Place	each	tilt	foot	rubber	on	stacking	holders	(three	locations).
Foot	rubber
TIP:
•	 To	remove	the	stacking	holders,	perform	the	above	steps	in	reverse	order.
6. Installation and Connections  
						

							141
7. Maintenance
❶ Cleaning the Lens
•	 Turn	off	the	projector	before	cleaning.
•	 The	projector	has	a	plastic	lens.	Use	a	commercially	available	plastic	lens	cleaner.
•	 Do	not	scratch	or	mar	the	lens	surface	as	a	plastic	lens	is	easily	scratched.
•	 Never	use	alcohol	or	glass	lens	cleaner	as	doing	so	will	cause	damage	to	the	plastic	lens	surface.
 WARNING
•	 Please	do	not	use	a	spray	containing	flammable	gas	to	remove	dust	attached	to	the	lens,	etc.	Doing	so	may	
result	in	fires.
❷ Cleaning the Cabinet
Turn	off	the	projector,	and	unplug	the	projector	before	cleaning.
•	 Use	a	dry	soft	cloth	to	wipe	dust	off	the	cabinet.
	 If	heavily	soiled,	use	a	mild	detergent.	
•	 Never	use	strong	detergents	or	solvents	such	as	alcohol	or	thinner.	
•	 When	cleaning	the	ventilation	slits	or	the	speaker	using	a	vacuum	cleaner,	do	not	force	the	brush	of	the	vacuum	
cleaner	into	the	slits	of	the	cabinet.
Vacuum	the	dust	off	the	ventilation	slits.
•	 Poor	ventilation	caused	by	dust	accumulation	in	ventilation	openings	(intake,	exhaust,	also	at	the	bottom	of	the	
projector)	can	result	in	overheating	and	malfunction.	These	areas	should	be	cleaned	regularly.
•	 Do	not	scratch	or	hit	the	cabinet	with	your	fingers	or	any	hard	objects
•	 Contact	your	dealer	for	cleaning	the	inside	of	the	projector.
NOTE:	Do	not	apply	volatile	agent	such	as	insecticide	on	the	cabinet,	the	lens,	or	the	screen.	Do	not	leave	a	rubber	or	vinyl	product	
in	prolonged	contact	with	it.	Otherwise	the	surface	finish	will	be	deteriorated	or	the	coating	may	be	stripped	off.	 
						

							142
8. User Supportware
❶ Operating Environment for Software available on web site.
Names and Features of Bundled Software Programs
Name	of	software	programFeatures
Virtual	Remote	Tool
(Windows	only)
When	the	computer	and	projector	are	connected	using	a	network	(wired	LAN),	
such	operations	as	turning	the	projector’s	power	on	and	off	and	switching	the	
signal	can	be	performed.	It	is	also	possible	to	send	an	image	to	the	projector	
and	register	it	as	the	background	logo.	Once	the	image	is	registered,	it	can	be	
locked	to	prevent	the	logo	from	being	overwritten.
PC	Control	Utility	Pro	4
PC	Control	Utility	Pro	5	(for	Mac	
OS)
This	is	a	software	program	used	to	operate	the	projector	from	the	computer	
when	the	computer	and	the	projector	are	connected	with	LAN.	(→	page	133)
•	 PC	Control	Utility	Pro	4	can	be	used	with	a	serial	connection.
NOTE:
•	 To	connect	the	projector	to	the	network	by	using	the	Virtual	Remote	Tool,	PC	Control	Utility	Pro	4,	PC	Control	Utility	Pro	5,	please	
configure	the	settings	of	[SETUP]	→	[NETWORK	SETTINGS]	in	the	on-screen	menu	(→ page 107).
Download service
For	the	update	information	about	these	software	programs,	visit	our	website:
URL:	http://www.nec-display.com/dl/en/index.html
Operating Environment
[Windows]
Supported	OSWindows	8.1,	Windows	8.1	Pro,	Windows	8.1	Enterprise,	Windows	8,	Windows	
8	Pro,	Windows	8	Enterprise
Windows	7	Home	Basic,	Windows	7	Home	Premium,	Windows	7	Professional,	
Windows	7	Ultimate,	Windows	7	Enterprise
Windows	Vista	Home	Basic,	Windows	Vista	Home	Premium,	Windows	Vista	
Business,	Windows	Vista	Ultimate,	Windows	Vista	Enterprise
Windows	XP	Home	Edition	(32-bit	version)	Service	Pack	3	or	later
Windows	XP	Professional	(32-bit	version)	Service	Pack	3	or	later
[Mac]
Supported	OSMac	OS	X	v10.6,	v10.7,	v10.8,	v10.9 
						

							143
❷ Installing Software Program
Installation for Windows software
The	software	programs	except	PC	Control	Utility	Pro	5	support	Windows	8.1,	Windows	8,	Windows	7,	Windows	Vista,	
and	Windows	XP.
NOTE:
•	 To	install	or	uninstall	each	software	program,	the	Windows	user	account	must	have	“Administrator”	privilege	(Windows	8.1,	
Windows	8,	Windows	7,	Windows	Vista)	or	“Computer	Administrator”	privilege	(Windows	XP).
•	 Exit	all	running	programs	before	installation.	If	another	program	is	running,	the	installation	may	not	be	completed.
•	 To	run	Virtual	Remote	Tool	or	PC	Control	Utility	Pro	4	on	Windows	8.1,	Windows	8,	Windows	XP	Home	Edition,	and	Windows	
XP	Professional,	“Microsoft	.NET	Framework	Version	2.0”	is	required.	The	Microsoft	.NET	Framework	Version	2.0,	3.0	or	3.5	is	
available	from	Microsoft’s	web	page.	Download	and	install	it	on	your	computer.
 
Download Service and Operating Environment 
Please visit our Dukane website about operating environment and download service 
for each software. Also go to the NEC website for the latest software 
Visit www.dukane.com and go to the Service page for downloads and links.
www.dukane/av/service/downloads.asp
Or visit URL: www.nec-display.comdl/en/index.html: 
Download - Projector ----> Software and Driver 
 
8. User Supportware  
						

							144
2	 Click	a	software	program	you	wish	to	install	on	the	menu	window.
	 The	installation	will	start.
•	 Follow	the	instructions	on	the	installer	screens	to	complete	the	installation.
TIP:
Uninstalling	a	Software	Program
Preparation:
Exit	the	software	program	before	uninstalling.	To	uninstall	the	software	program,	the	Windows	user	account	must	
have	“Administrator”	privilege	(Windows	8.1,	Windows	8,	Windows	7,	and	Windows	Vista)	or	“Computer	Administra-
tor”	privilege	(Windows	XP).
•	For	Windows	8.1/Windows	8/Windows	7/Windows	Vista
1	 Click	“Start”	and	then	“Control	Panel”.
	 The	Control	Panel	window	will	be	displayed.
2	 Click	“Uninstall	a	program”	under	“Programs”
	 The	“Programs	and	Features”	window	will	be	displayed.
3	 Select	the	software	program	and	click	it.
4	 Click	“Uninstall/Change”	or	“Uninstall”.
	 •	When	the	“User	Account	Control”	windows	is	displayed,	click	“Continue”.
	 Follow	the	instructions	on	the	screens	to	complete	the	uninstallation.
•	For	Windows	XP
1	 Click	“Start”	and	then	“Control	Panel”.
	 The	Control	Panel	window	will	be	displayed.
2 Double-click “Add / Remove Programs”.
	 The	Add	/	Remove	Programs	window	will	be	displayed.
3	 Click	the	software	program	from	the	list	and	then	click	“Remove”.
	 Follow	the	instructions	on	the	screens	to	complete	the	uninstallation.
8. User Supportware  
						

							145
Using on Mac OS
Step 1: Install PC Control Utility Pro 5 on the computer.
3.	 Double-click	the	“Mac	OS	X”	folder.
4.	 Double-click	“PC	Control	Utility	Pro	5.pkg”.	
	 The	installer	will	start.
5.	 Click	“Next”.	
	 “END	USER	LICENSE	AGREEMENT”	screen	will	be	displayed.
6.	 Read	“END	USER	LICENSE	AGREEMENT”	and	click	“Next”.	
	 The	confirmation	window	will	be	displayed
7.	 Click	“I	accept	the	terms	in	the	license	agreement”.	
	 Follow	the	instructions	on	the	installer	screens	to	complete	the	installation.
TIP:
•	Uninstalling	a	software	program
1.	 Put	the	“PC	Control	Utility	Pro	5”	folder	to	the	Trash	icon.
2.	 Put	the	configuration	file	of	PC	Control	Utility	Pro	5	to	the	Trash	icon.
•	 The	configuration	file	of	PC	Control	Utility	Pro	5	is	located	in	“/Users//Application	Data/NEC	
Projector	User	Supportware/PC	Control	Utility	Pro	5”.
 
1. Go to the Dukane or NEC website for the latest Mac software. 
    Visit. www.dukaneav.com. and go to the Service page for downloads and links. 
    www.dukane.com/av/service/downloads.asp Or visit URL: www.nec-display.com/dl/en/index.html
 
2. Download - Projector → Software & Driver 
8. User Supportware  
						

							146
❸ Operating the Projector Via the LAN (Virtual Remote Tool)
This	will	help	you	perform	operations	such	as	projector’s	power	on	or	off	and	signal	selection	via	a	LAN	connection.	It	
is	also	used	to	send	an	image	to	the	projector	and	register	it	as	the	logo	data	of	the	projector.	After	registering	it,	you	
can	lock	the	logo	to	prevent	it	from	changing.
Control Functions
Power	On/Off,	signal	selection,	picture	freeze,	picture	mute,	audio	mute,	Logo	transfer	to	the	projector,	and	remote	
control	operation	on	your	PC.
Virtual	Remote	screen
Remote	Control	WindowToolbar
This	section	provides	an	outline	of	preparation	for	use	of	Virtual	Remote	Tool.
For	information	on	how	to	use	Virtual	Remote	Tool,	see	Help	of	Virtual	Remote	Tool.	(→	page	148)
NOTE:
•	 Logo	data	(graphics)	that	can	be	sent	to	the	projector	with	Virtual	Remote	Tool	has	the	following	restrictions:
	 (Only	via	serial	or	LAN	connection)
*	 File	size:	Within	256	kilobytes
*	 Image	size:	Within	the	resolution	of	the	projector
*	 File	format:	PNG	(Full	color)
•	 Logo	data	(image)	sent	using	the	Virtual	Remote	Tool	will	be	displayed	in	the	center	with	the	surrounding	area	in	black.
8. User Supportware  
						

							147
Connect the projector to a LAN.
Connect	the	projector	to	the	LAN	by	following	the	instructions	in	“Connecting	to	a	Wired	LAN”	(→	page	133)	and	“10.	
Controlling	the	Projector	by	Using	an	HTTP	Browser”	(→	page	42)
Start Virtual Remote Tool
Start using the shortcut icon
•	 Double-click	the	shortcut	icon	 on the Windows Desktop.
Start from the Start menu
•	 Click	[Start]	→	[All	Programs]	or	[Programs]	→	[NEC	Projector	User	Supportware]	→	[Virtual	Remote	Tool]	
→	[Virtual	Remote	Tool].
	 When	Virtual	Remote	Tool	starts	for	the	first	time,	“Easy	Setup”	window	will	be	displayed.
	 The	“Easy	Setup”	feature	is	not	available	on	this	model.	Click	“Close	Easy	Setup”.
	 Closing	the	“Easy	Setup”	window	will	display	the	“Projector	List”	window.
	 Select	your	projector	you	wish	to	connect.	This	will	display	the	Virtual	Remote	screen.
NOTE:
•	 When	[NORMAL]	is	selected	for	[STANDBY	MODE]	from	the	menu,	the	projector	cannot	be	turned	on	via	network	connection.
TIP:
•	 The	Virtual	Remote	Tool	screen	(or	Toolbar)	can	be	displayed	without	displaying	“Easy	Setup”	window.
	 To	do	so,	click	to	place	a	check	mark	for	“		Do	not	use	Easy	Setup	next	time”	on	the	screen.
8. User Supportware