Dukane Projector 9010 User Manual

							21
Installation of the Projector
Connecting the projector to other devices
HDMI / DVI connection
Signals from image source offer the best projection image quality when sent through HDMI. 
Therefore, try to use input devices with HDMI output as the source of image.
  
COMPONENT 2SDI / HDSDI / 3G
COMPONENT 1
YPbPr
10/100 BASE-T RS-232 WIRED REMOTE 12V TRIGGERIII
350mASYNC IN SYNC OUT
IN OUT G/Y B/Pb R/Pr H V VGA
HDMI   
HDMI  STEREO DVI
HDMI/DVI input source
(BD/HD-DVD/DVD player, HD set-top-box, 
gaming consoles and so forth)
   
12V Trigger connection
If your home theatre system includes a projector screen, screen cover or other 12V Trigger equipment,
	\f


\f
%
						

							22Installation of the Projector
RGB connection
Connect your PC or other devices with RGB output to the RGB input connectors on the projector to be 
used as the source of image input.
COMPONENT 2SDI / HDSDI / 3G
COMPONENT 1
YPbPr
0/100 BASE-T RS-232 WIRED REMOTE 12V TRIGGERIII
350mA
IN OUT G/Y B/Pb R/Pr H V
VGA
HDMI   
HDMI 

Desk Top or Notebook
COMPONENT 2SDI / 3G
COMPONENT 1
YPbPr-T RS-232WIRED REMOTE
12V TRIGGERIII
350mASYNC IN SYNC OUT
OUT G/Y B/Pb R/Pr H V VGA
HDMI   
HDMI  STEREO DVI
G/Y B/Pb R/Pr
HV
Desk Top or Notebook 
						

							23
Installation of the Projector
COMPONENT connection
J	


						

							24Installation of the Projector
3D mode
There are few ways to go to the 3D mode
#
OSD menu: Go to Main Me

nu “Input > Input Selection”, and select STEREO DVI
#
 Remote control: Press hot key “5” to go to STEREO DVI directly
#
 Network Webpage: Go to “Source/general” > “Source” and select STEREO DVI
#
 RS232 Commands : Use “ Input Selection” to select STEREO DVI
When this function is blanking. The 3D Mode is not available
2D mode
Please note that OSD menu is not available in 3D mode. The ways to switch back to 2D mode are:
#
Remote contro

l: Press any of the input key 1-4 will switch back to 2D mode.
#
 Network Webpage: Go to “Source/general” > “Source” and select any other source that are 
available. 
#
 RS232 Commands: Use “ Input Selection” to select any other source that are available.
Turning on the projector
Refer to the instructions covered in 
“ Page 15 : Installation the projector. “.
Changing OSD language
By factory default, the OSD menu of the projector is displayed in English. If you wish to 
switch to a different language, you can go to MENU   CONTROL  Language and 
choose the lang

uage you prefer for the OSD.  
						

							25
Installation of the Projector
Adjusting screen orientation

						

							26Installation of the Projector
Rear projection - desktop installation 
Press 
MENU   ALIGNMENT 

						

							27
REMOTE CONTROL
Remote control
 
2
32
4 1
5
INPUT
ASPECT
RATIO
AUTO IMAGE
PAUSE TEXT
MENU
SHARPN
PHASE COLOR TINT
ADDRESS
SWAP
PIP
1
3
4            
6
7 2
5
1.  ON 
This button is used to turn on the projector.
2. 
 OFF 
This button is used to turn off the projector.
3. 
12345 
These buttons on the remote control are the hotkeys 
for different image source. By factory default, these 
are:  
1 = HDMI 1 
2 = RGB D-15 
3 = COMPONENT2 
4 = COMPONENT1 
5 = Stereo DVI
Note: These buttons may not work at PIP mode. 

						

							28REMOTE CONTROL
 AUTO  IMAGE   
  This button is used to  Resync the 
  image; when the image signal 
  becomes unstable or image  
  quality deteriorates simply press 
  this button and the  projector will 
  automatically adjust the screen 
  dimension, phase, timing and so 
  forth.(The adjustments also apply 
  to PIP input).  
 CONTRAST  
  Adjust the level of white in the  
  image to increase or decrease 
 image contrast.  
 BRIGHTNESS  
  Adjust the level of black in the  
  image to increase or decrease 
 image brightness.  
 SHARPNESS  
   Adjust image sharpness and 
 clarity. 
 PHASE  

 {

	
`\b\f>
\
&\f> 
  distorts or  appears to be wavy, 
  press this button to adjust.  
 COLOR  
  This function not available for this model.  
 TINT  
  This function not available for this model.  
PIP PIP  
   Use this button to display or disable PIP.  
SWAP SWAP  
  Use this button to switch the sources of image PIP  
 display.  
ADDRESS ADDRESS   
  *Only 2 addresses are possible* 
  Press and hold the ENTER button  
  and press Address button until the  

 \b


\b
	
`	\f\
\f
 
  (approximately 5 seconds) to 
  change the receiving address of  
  the remote control. If you use one  
  remote control to operate two  
 

different projectors, you can  
  assign different address for the  
  two projectors so that when you  
  operate projector A, projector B  
  will not be affected. 
Note:  
Some keys may not work when STEREO DVI is selected. 
 
  
						

							29
OSD Menu description
OSD Menu Tree 
INPUT
Input Selection
HDMI1 
HDMI2 
RGB D -15 
YUV1 
RGBH V/ Y U V2 
SDI/HDSDI/3G 
STER EO DVI


\b	
 Auto 
YUV HD 
YUV STD 
RGB -PC 
RGB -Video
Input Locking Auto 
48Hz, 50Hz, 60Hz
Auto Power Off On 
Off
Auto Power ON On 
Off
No Signal Logo 
Blue 
Black 
White
Auto Image Adjust Off, Auto 
Always
IMAGE Contrast 0~200
Brightness 0~200
Sharpness 0~200
Noise Reduction 0 ~200
Color Temperature
3200K, 5400K, 6500K, 
9300K, Native
Input Balance Black Balance Offset 
Red Offset 
Green Offset 
Blue Offset 
White Balance 
Red Gain 
Green Gain 
Blue Gain
Aspect Ratio 5:4 ,  4:3,   16:10 
16:9,  1.88,  2.35 
Letterbox,    Native,     
unscaled
Timings H Total 
H Start 
H Phase 
V Start
Auto Image Execute
LAYOUT Zoom
Off
CROP  
ZOOM
Main Select HDMI1 
HDMI2 
RGB D -15 
YUV1 
RGBH V/ Y U V2 
SDI/HDSDI/3G
PIP Select HDMI1 
HDMI2 
RGB D -15 
YUV1 
RGBH V/ Y U V2 
SDI/HDSDI/3G
PIP Position Top Left 
To p  R i g h t  
Bottom Left 
Bottom Right 
Split L-R
PIP On, Off
 
LAMPS Mode
Eco 
Normal 
Power
LAMPS Single 
Dual
High Altitude Mode On 
Off
Power 0 ~35 (78.3% - 100%)
Lamp1 Status On 
Off
Lamp2 Status On 
Off
Lamp1 Run Time XX HRS
Lamp2 Run Time XX HRS 
						

							30OSD Menu description
ALIGNMENT
Rear Projection
On 
Off
Ceiling Mode On 
Off
Lens Control Zoom/Focus 
Shift V 
Shift H
Dynamic Contrast On  
Off 
Gamma 1.8      2.0     2.2 
2.35     2.5    Dicom  sim
Internal Patterns O n (1~12 Pat t e r n) 
Off (0 off )
Color Space Native,  EBU,  SMPTE 
Custom
Lens To  
Midposition Execute
Wa r p Horizontal Keystone 
Vertical Keystone 
Rotation 
Pincushion / Barrel 
Top Left Cor ner 
Top Right Cor ner 
Bottom Left Cor ner 
Bottom Right Cor ner
Blanking Top,     Bottom 
Left,     Right,  Reset
Edge blend Status 
White Level 
    Top 
    Bottom 
    Left 
    Right 
Black Level 
    Top 
    Bottom 
    Left 
    Right 
    All 
    Red 
    Green 
    Blue 
Reset 
Adjust Lines
Control IR Address
1 
2
Eco Network Power On 
Off
Network IP Address 
Subnet mask 
Gateway 
DHCP
ControlMenu Position
Top Left 
To p  R i g h t  
Bottom Left 
Bottom Right 
Center
Start Up Logo On 
Off
Start Up Chime On 
Off
Button 1 HDMI1  HDMI2 
RGB D -15 
YUV1 
RGBH V/ Y U V2 
SDI/HDSDI/3G 
STER EO DVI
Button 2
Button 3
Button 4
Button 5
Trigger 1
5:4 ,  4:3,   16:10 
16:9,  1.88,  2.35 
Letterbox,    Native, Auto 
unscaled
Trigger 2
Auto Source
On 
Off
Language English 
French 
Spanish 
German 
Por t ug uese 
\f
 
Chinese Traditional 
Japanese 
Korean
Service Model
Read-only information
Serial Number
Software Version
Active/PIP source
Pixel Clock
Signal Format
H/V Refresh Rate
Lamp1 Run Time
Lamp2 Run Time
Lamp Hour Reset
Lamp1 Hour Reset 
Lamp2 Hour Reset
Projector Run Time Read-only information
Blue Only On 
Off
Factory Reset The command will be 
$

	
\b
\b	

in the prompt dialog box