Dukane Projector 9010 User Manual

							31
OSD Menu description
OSD Description
1.   Press the MENU button on the remote control or on the back of the proje\
ctor to bring up the OSD Menu.
2.   You will see seven functional menus (Input, Image, Layout, Lamp, Alignment, Control and Service). Press 
* or + to 
select the desired sub menu. 
3. 
\b\f\f

						

							32OSD Menu description
#
Component 
For SDTV and EDTV resolutions, uses the YUV STD. For all other resolutions YUV HD is used.
Input Locking
Use this function to specify the frequency of the image input signal. You can let the projector 
determine the optimal projection frequency or force the projector to project image at the frequency 
you specify.
#
Auto 
  The present value for this function is 
Auto. If you specify vertical refresh frequency from the 
input device to be b

etween 48~62Hz, the projector will automatically lock the frequency of the 
input signal so that both signal input and output will be refreshed at the same frequency in order 
to achieve optimal image output. If the frequency of the input signal falls between 24~31Hz, the 
projector will automatically double the vertical refresh frequency. If the frequency of the input 
signal falls between 31~48Hz or exceeds 62Hz, the projector will automatically set the frequency 
to 60Hz.
#
 50Hz  
 Choose this option to set image output frequency at 50Hz.
#
 60Hz  
 Choose this option to set image output frequency at 60Hz.
 
 
-b$
&&-b-f
-b
>-b
-b-

-f
?-b-f@
-b-f&&-b
>-b-f-b-f-
 main input signal.
Auto Power Off
The default value is  OFF. If you set it to  ON, the projector will automatically shut down after 20 
minutes without i
nput signal. 
Auto Power ON
The default value is  Off. If you set it to  ON, the projector will automatically start up when it is connected 


]
\b





\b
\b+\f
\b
\b


	
]
\f



	
\f
>

	
\f
\f



\f
	\b



\b
\b
\f

\f
+\f
\f

\f
	


\b


u do not need this 
function, please set it to  Off.
No Signal
Use this function to specify the content or color to be displayed on the blank screen when no input 
signal is available. You can choose from  Logo, Blue , Black , White . The default value is Logo .
Auto Image Adjust

						

							33
OSD Menu description
IMAGE
Contrast
Use    to adjust the contrast of the projected image. You can connect the projector to an external 
image source to display an image resembling the one shown below for adjustment. It is recommended 
that you adjust the projected image according to the results shown below so that the brightness of the 
spectrum remains constant throughout and achieve maximum contrast between black and white. 
The following image illustrates the results of direct contrast adjustment using a random image: 
 Lowered contrast Enhanced contrast 

Original image 
						

							34OSD Menu description
Brightness
Use 
  to adjust the brightness of the projected image. You can connect the projector to an external 
image source to display an image resembling the one shown (PLUGE, Picture Line-Up Generation 
Equipment) for adjustment. Although there are numerous versions of PLUGE image, they are typically 
comprised of blocks of black, white and gray on top of a black background. 
 
Contrast, Brightness, Saturation and Tint are interrelated options that affect 

	
\b
						

							35
OSD Menu description
Sharpness
The adjustment of sharpness primarily changes the value of high frequency detail. You can  connect 
the projector to an external image source to display an image resembling the one shown below to 
adjust the image sharpness.
 
The following image illustrates the results of direct sharpness adjustment using a random image: 
 
 Reduced sharpness Enhanced sharpness 

Original image (Value = 100)
Noise Reduction
Use    to adjust the noise of the projected image. This function is suitable for the elimination of 
image noise from interleaving SD input. Generally speaking, reducing image noise will lower the 
value of high frequency detail and make the image appear more mellow. 
 

noise reduction 
						

							36OSD Menu description
Color Temperature
You can choose from 3200K, 5400K, 6500K, 9300K and Native
.
Color temper
ature refers to the change in light color under different energies that is perceived by the 
naked eye. The change of color temperature from low to high for visible light goes from orange red   
white   blue  
.
J
\b
\b+\f
	

\b
\b	
\b
\f
\f

	


						

							37
OSD Menu description
    Press  
to adjust the offset of red in dark scales. 
#
 Green Offset
 
    Press  

 to adjust the offset of green in dark scales. 
#
 Blue Offset
 
    Press  

 to adjust the offset of blue in dark scales. 
#
 White Balance
 
    This funct

ion involves the adjustment of the following red, green and blue gains. The text    
itself is decorative.
#
 Red Gain
 
    Press  
  to adjust the gain of red in bright scales.
#
 Green Gain
 
    Press  

 to adjust the gain of green in bright scales.
#
 Blue Gain
 
    Press  
  to adjust the gain of blue in bright scales.
Aspect Ratio
Use this function to adjust the aspect ratio of the projected image. Use    to adjust the ratio of 
image length and width. 
J
\b
\b+\f

	
\f@
\f

						

							38OSD Menu description
Native input 
4:3
Output aspect ratio
16:9
Output aspect ratio
1.88 Output aspect ratio
2.35 Output aspect ratio
5:4Output aspect ratio
4:3
Output aspect ratio
Native 
Output aspect ratio
Letterbox
Cropped portion of the image
Note :  that when used for commercial purposes, including: projection of image in movie theatres, 
hotels, cafeteria and other public venues, compression or extension of image achieved through the 
change of aspect ratio may constitute copyright infringement to the rightful owner of the image. 
Please do so at your own discretion.
Timings
#
H Total 
Press 
 to adjust the horizontal total. 
 Use this fu
 nction to adjust the clock frequency of pixel sampling (horizontal pixel frequency  



		


\f\b
\b	

&

]Q
						

							39
OSD Menu description
#
H Start
 
 Use   

	
\f


\b

	+\f
\b@
	
\f
 
 If the projected image is not at the center of the screen (i.e. shifted to right or left) and 

\f

&
\b>
\f
\f



	\f


	+\f
\b@
	
\f

J

 
 following image is an example of test image from an external signal source:
     
Native pictureSkewed leftSkewed right
 
 
#
H Phase
 
Use   

	

\f


\b

	+\f
	\f 
   Use this function to adjust the phase of pixel sampling clock (relative to input signal).    



	
\f

`\b
\b
\f
\f

						

							40OSD Menu description
LAYOUT
Zoom
Due to the fact that some consumers may still be using older television systems, some TV programs 
may not display the edges of the image. Use this function to hide the image edge by choosing one of 
the following three options:
#
Off 
 Setting it to off makes no change to the projected image. 
#
 Crop 
  Setting it to "Crop" will add two "masks" equivalent to 3% of horizontal resolution on either side of 
the image and t
 wo similar masks above and below the projected image. 
#
 Zoom 
  You can use this function to enlarge the image's horizontal resolution over the 106% of the  default 
aspect rati
 o. Any portion that exceeds the original image will be cropped. 
When you set aspect ratio to " Native" or "Unscaled" , be sure to set Zoom to "Off " or "Crop".
 
16:10Off Crop Zoom
5:4
2.35