Eiki Eip-1000t Dlp Projector Owners Manual

28
Turning the Projector On/Off
Remove the lens cap and press
oSTANDBY-ON on the projector or
fON on the remote control.
•About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Red: The lamp is on.
Blinking in red:The lamp is warming up
or shutting down.
Green:The lamp is shut down abnor-
mally or the lamp should be re-
placed.
• When switching on the projector, a slight flick-
ering of the image may be experienced within
the first minute after the lamp has been...

29
On-screen Display (confirmation message)
1
2
Turning the Power off (Putting
the Projector into Standby Mode)
Press oSTANDBY-ON on the pro-
jector or eSTANDBY on the re-
mote control, then press that but-
ton again while the confirmation
message is displayed, to put the
projector into standby mode.
Unplug the power cord from the AC
outlet after the cooling fan stops.
• The power indicator on the projector
blinks in red while cooling.
• The power indicator changes to green
when the projector finishes...

30
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Image Projection
Rotate the focus ring to adjust the fo-
cus while watching the projected image.
Focus ring
Adjusting the Projected Image
2 Adjusting the Screen Size
You can adjust the screen size using
the zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the screen size.
Zoom ring
Switching the Input Mode
PressCINPUT 1, CINPUT 2,
DINPUT 3 or EINPUT 4 on the remote
control to select the input...

31
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly...

32
Image Projection (Continued)
Displaying the Black Screen
and Turning off the Sound
Temporarily
Adjusting the Volume
Press K/L on the remote control or
–O/Q+ on the projector to adjust the vol-
ume.
• Pressing K/–O will lower the volume.
• Pressing L/Q+ will raise the volume.
• When the projector is connected to external
equipment, the volume level of the external
equipment changes in accordance with the
volume level of the projector. Set the projector’s
volume to the lowest level when turning the...

33
0 KeystoneADJ. END
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
• The Keystone Correction can be adjusted up
to an angle of approximately ±13 degrees and
the screen can also be set up to an angle of
approximately ±13 degrees (when the resize
mode is set to “STRETCH” (see page 34)).
Note
1
2...

34
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose “STRETCH”, “SIDE BAR” or “CINEMA ZOOM” image.
Press HRESIZE.• See page 43 for setting on menu screen.RESIZE button
VIDEO
• “STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
: Cutout area on which images cannot be projected.Input Signal
DVD / Video Image typeOutput screen image
STRETCH SIDE BAR
480I, 480P,...

35
: Cutout area on which images cannot be projected.
Computer
Input Signal
STRETCHOutput screen image
Computer Image type SIDE BAR
SXGA
(1280K1024) Resolution lower than
SVGA
SVGA
Resolution higher than
SVGA
1280K720
4:3 aspect ratio
5:4 aspect ratio
16:9 aspect
ratio
SVGA (800 K 600)
XGA (1024 K 768)
SXGA (1280 K 960)
SXGA L (1400 K 1050)SXGA (1280 K 1024)1280 K 720
640 K 480
J
854 K 480
854
 K 480640 K 480 854 K 480
STRETCH SIDE BAR
Other aspect ratios4:3 aspect ratio
CINEMA ZOOM...

36
Operating with the Remote Control
Freezing a Moving Image
Press NFREEZE.• The projected image is frozen.
Press  NFREEZE again to return
to the moving image from the cur-
rently connected device.
1
2
Selecting the Picture Mode
Press  GPICTURE MODE.• When pressing  GPICTURE MODE, the picture
mode changes in the following order:
Standard Natural Dynamic Movie1 Movie2
You can select the appropriate picture
mode to best match the projected im-
age you are watching.
• See page  41 for details on the picture...

37
The following shows the items that can be set in the projector.
Menu Items
“Screen adjustment (SCR-ADJ)” menu
INPUT 1 (RGB)/INPUT2 (RGB)
“Picture” menu
Picture
Picture Mode
Contrast 0 0
0
0K
7500SCR - ADJ PRJ - ADJ Help
BrightRedBlue
1CLR TempBright Boost
Lamp Setting Standard
Bright
Reset
SEL./ADJ. ENTER END
Picture
Resize 0
SCR - ADJ
PRJ - ADJ Help
Keystone
OSD Display
Background
PRJ Mode
Language Front
English Logo On Stretch
SEL./ADJ. ENTER END
Main menu Sub menuPicture
Page  41
+30
-30Contrast...