Epson AcuLaser 2600DN User Manual

Paper Handling51
3
3
3
3
3
3
3
3
3
3
3
3
3. Load a stack of paper into the paper cassette. Make sure to 
load it with the printable surface up.
Note:
❏Load paper after aligning the edges of the paper carefully.
❏Do not load paper that exceeds the maximum stack height.
❏To change the paper size loaded in the paper cassette, see  
Changing the paper size on page 52 for instructions.
 

52Paper Handling 4. Reinsert the paper cassette.
Note:
After loading paper, set the LC Size setting to match the loaded 
paper size on the control panel.
Changing the paper size
Follow the steps below to change the paper size loaded in the 
paper cassette.
1. Pull out the paper cassette. If paper is loaded in the paper 
cassette, remove it.
 

Paper Handling53
3
3
3
3
3
3
3
3
3
3
3
3
2. Push the tray in the paper cassette down.
3. Remove the three screws securing the tray in the paper 
cassette.
 

54Paper Handling 4. Slide the three paper guides to fit the paper size that you want 
to use.
5. Secure the three paper guides with the three screws.
 

Paper Handling55
3
3
3
3
3
3
3
3
3
3
3
3
6. Load the paper and reinsert the paper cassette.
Note:
After loading paper, set the LC Size setting to match the loaded 
paper size on the control panel.
Output tray
The output tray is located on the top of the printer. Since printouts 
are output face-down, this tray is also referred to as the face-down 
tray. This tray can hold up to 250 sheets.
 

56Paper Handling If the printouts do not stack well, open the extension on the output 
tray.
Printing on Special Media
You can print on special media which include Epson paper such 
as the following. 
Note:
Since the quality of any particular brand or type of media may be changed 
by the manufacturer at any time, Epson cannot guarantee the quality of 
any type of media. Always test samples of media stock before purchasing 
large quantities or printing large jobs.
EPSON Color Laser Paper
When loading...

Paper Handling57
3
3
3
3
3
3
3
3
3
3
3
3
❏You can also make these settings on the Tray Menu in the 
control panel. See  Tray Menu on page 229.
EPSON Color Laser Transparencies
Epson recommends the use of EPSON Color Laser 
Transparencies.
Note:
Duplex printing is not available for transparencies.
Transparencies can be loaded into the MP tray only. When using 
transparencies, you should make paper settings as shown below:
❏Make settings on the Basic Settings in the printer driver.
❏You can also make these...

58Paper Handling ❏Hold each sheet by its edges, as oil from your fingers may 
transfer to the surface and damage the printable surface of the 
sheet. The Epson logo appears on the printable side.
❏When loading transparencies in the MP tray, insert the short 
edge first as shown below.
❏When using transparencies, load them in the MP tray and set 
the Paper Type setting to Transparency in the printer driver.
❏When the Paper Type setting in the printer driver is set to 
Transparency, do not load any other...

Paper Handling59
3
3
3
3
3
3
3
3
3
3
3
3
c
Caution:
Do not use window envelopes. The plastic on most window 
envelopes will melt when it comes into contact with the fuser.
Note:
❏Depending on the quality of envelopes, the printing environment, 
or the printing procedure, envelopes might be wrinkled. Make a trial 
print run before you print on a lot of envelopes.
❏Duplex printing is not available for envelopes.
When loading envelopes, you should make paper settings as 
shown below:
❏Make settings on the...

60Paper Handling ❏When printing on envelopes, be sure to set the lever on the 
fuser unit to the envelope position before loading the 
envelopes. After printing envelopes, be sure to reset the lever 
to the original position. Printing on media other than 
envelopes when the lever is set to the envelope position may 
cause poor print quality because the printer fails to fix toner 
to the media. It also may cause paper jam and dirty printouts 
because of the toner that adheres to the rollers inside the...