Epson AcuLaser 2600N User Manual

							Troubleshooting351
11
11
11
11
11
11
11
11
11
11
11
11
If the optional Duplex Unit is installed, lift up the Duplex Unit. 
Hold it and gently pull out any sheets of paper. Be careful not 
to tear the jammed paper.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE, or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot. If you must touch one of these areas, open 
cover A and B, then wait 30 minutes to allow the heat to 
subside before doing so.
 
						

							352Troubleshooting 5. Open cover B.
6. Hold the guide up by holding the green tab, and gently pull 
out any sheets of paper. Be careful not to tear the jammed 
paper.
 
						

							Troubleshooting353
11
11
11
11
11
11
11
11
11
11
11
11
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE, or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot. If you must touch one of these areas, open 
cover A and B, then wait 30 minutes to allow the heat to 
subside before doing so.
If you can remove the paper, close covers B and A. If you 
cannot remove the paper, go to the next step.
7. Turn the handles on both sides of the fuser unit to unlock 
them.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE, or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot. If you must touch one of these areas, open 
cover A and B, then wait 30 minutes to allow the heat to 
subside before doing so.
 
						

							354Troubleshooting 8. Lift the fuser unit out of the printer.
9. Remove the paper. If the paper is still jammed in the fuser, 
turn the green knob on the back of the fuser to remove it.
 
						

							Troubleshooting355
11
11
11
11
11
11
11
11
11
11
11
11
10. Lower the fuser unit into the printer making sure that the 
guide posts slide into the holes on the bottom of the unit.
11. Turn the handles on both sides of the fuser unit to lock them.
 
						

							356Troubleshooting 12. Close covers B and A.
13. Open the MP tray and reload the paper.
Jam MP, A (MP tray and cover A)
Follow the steps below to clear paper jams at the MP tray and 
cover A.
1. Remove all paper that is loaded on the MP tray.
 
						

							Troubleshooting357
11
11
11
11
11
11
11
11
11
11
11
11
2. Gently pull out any sheets of paper that have fed part way 
into the printer.
3. Close the MP tray.
Note:
Close the expansion trays, if needed, before closing the MP tray.
 
						

							358Troubleshooting 4. Push the latch on cover A to the left and open the cover until 
it stops.
5. If the optional Duplex Unit is not installed, gently pull out any 
sheets of paper. Be careful not to tear the jammed paper.
 
						

							Troubleshooting359
11
11
11
11
11
11
11
11
11
11
11
11
If the optional Duplex Unit is installed, lift up the Duplex Unit. 
Hold it and gently pull out any sheets of paper. Be careful not 
to tear the jammed paper.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE, or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot. If you must touch one of these areas, open 
cover A and B, then wait 30 minutes to allow the heat to 
subside before doing so.
6. Close cover A. Then open the MP tray and reload the paper.
Jam A, C1 (cover A and standard lower paper 
cassette)
Follow the steps below to clear paper jams at cover A and the 
standard lower paper cassette.
 
						

							360Troubleshooting 1. Remove all paper that is loaded on the MP tray. 
2. Close the MP tray. 
Note:
Close the expansion trays, if needed, before closing the MP tray.