Epson AcuLaser C1750N User Manual

							When IPv4 is selected:
❏Configure the following:
a
Select Type.
b Enter the following items:
❏IP Address of your printer
❏Network Mask
❏Gateway Address
When IPv6 is selected:
❏Configure the following:
a
Select Use Manual Address.
b Enter IP address of your printer.
c Enter the gateway address of your network.
When Dual Stack is selected:
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     51
 
						

							Configure the IPv4 Settings and IPv6 Settings.
8. Click Next.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     52
 
						

							9. Ensure that the wireless settings are displayed, and then click Apply.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     53
 
						

							The Complete configuration screen appears.
10. Wait a few minutes until the printer restarts to establish the wireless network.
11. Print a Printer Settings page from the operator panel.
See “Printing a Printer Settings Page” on page 125.
12. Confirm that “Wireless Status” is shown as “Good”, “Acceptable” or “Low” on the report.
Note:
When “Wireless Status” is “No Reception”, check if the wireless settings are correctly configured. To
reconfigure the wireless settings, click Next on the Complete configuration screen and then click
Return.
13. Click Next.
14. Follow the instructions until the Check Setup screen appears.
15. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     54
 
						

							If you see any errors, click Trouble Shooting Guide and follow the instruction.
16. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
17. Configure the required items on the Enter Printer Settings screen, and then click Next.
18. Select the software to be installed, and then click Install.
The “Congratulations!” screen appears.
19. Click Finish to exit this tool.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     55
 
						

							The wireless configuration is complete.
WPS-PIN
Note:
WPS-PIN (Wi-Fi Protected Setup-Personal Identification Number) is a method to authenticate and
register devices required for wireless configuration, by entering PIN assignments to a printer and
computer. This setting, performed through access point, is available only when the access points of your
wireless router supports WPS.
1. Select WPS-PIN, and then click Next.
2. Follow the instructions until the Check Setup screen appears.
3. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
If you see any errors, click Trouble Shooting Guide and follow the instruction.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     56
 
						

							4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click Next.
6. Select the software to be installed, and then click Install.
The “Congratulations!” screen appears.
7. Click Finish to exit this tool.
The wireless configuration is complete.
When the WPS-PIN operation is successful and the printer is rebooted, wireless LAN connection is
completed.
WPS-PBC
Note:
WPS-PBC (Wi-Fi Protected Setup-Push Button Configuration) is a method to authenticate and register
devices required for wireless configuration, by pressing the button provided on the access point via
wireless routers, and then performing WPS-PBC setting on the operator panel. This setting is available
only when the access point supports WPS.
1. Select WPS-PBC, and then click Next.
2. Follow the instructions until the Check Setup screen appears.
3. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     57
 
						

							If you see any errors, click Trouble Shooting Guide and follow the instruction.
4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click Next.
6. Select the software to be installed, and then click Install.
The “Congratulations!” screen appears.
7. Click Finish to exit this tool.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     58
 
						

							The wireless configuration is complete.
Note:
For WPS-PBC operation on the wireless LAN access point, refer to the manual supplied with the wireless
LAN access point.
When the WPS-PBC operation is successful and the printer is rebooted, wireless LAN connection is
completed.
Operator Panel
1. Select Operator Panel, and then click Next.
2. Follow the instructions until the Check Setup screen appears.
3. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
If you see any errors, click Trouble Shooting Guide and follow the instruction.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     59
 
						

							4. Check if the printer to be installed is listed in the Select Printer screen, and then click Next.
Note:
If the printer to be installed is not listed in the Select Printer screen, try the following steps:
❏Click Refresh to update the information.
❏Click Manually add using IP address, and then enter the details of the printer manually.
5. Configure the required items on the Enter Printer Settings screen, and then click Next.
6. Select the software to be installed, and then click Install.
The “Congratulations!” screen appears.
7. Click Finish to exit this tool.
The wireless configuration is complete.
EpsonNet Config
1. Select EpsonNet Config, and then click Next.
2. Follow the instructions until the Check Setup screen appears.
3. Confirm there are no errors displayed on the LCD panel, and then click Start Installation.
Epson AcuLaser C1750 Series     User’s Guide
Network Basics     60