Home > Epson > Printer > Epson AcuLaser C2600DN User Manual

Epson AcuLaser C2600DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C2600DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 473
    							Troubleshooting351
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    If the optional Duplex Unit is installed, lift up the Duplex Unit. 
    Hold it and gently pull out any sheets of paper. Be careful not 
    to tear the jammed paper.
    w
    Warning:
    Be careful not to touch the fuser, which is marked CAUTION 
    HIGH TEMPERATURE, or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot. If you must touch one of these areas, open 
    cover A and B, then wait 30 minutes to allow the heat to 
    subside before doing so.
     
    						
    							352Troubleshooting 5. Open cover B.
    6. Hold the guide up by holding the green tab, and gently pull 
    out any sheets of paper. Be careful not to tear the jammed 
    paper.
     
    						
    							Troubleshooting353
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    w
    Warning:
    Be careful not to touch the fuser, which is marked CAUTION 
    HIGH TEMPERATURE, or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot. If you must touch one of these areas, open 
    cover A and B, then wait 30 minutes to allow the heat to 
    subside before doing so.
    If you can remove the paper, close covers B and A. If you 
    cannot remove the paper, go to the next step.
    7. Turn the handles on both sides of the fuser unit to unlock 
    them.
    w
    Warning:
    Be careful not to touch the fuser, which is marked CAUTION 
    HIGH TEMPERATURE, or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot. If you must touch one of these areas, open 
    cover A and B, then wait 30 minutes to allow the heat to 
    subside before doing so.
     
    						
    							354Troubleshooting 8. Lift the fuser unit out of the printer.
    9. Remove the paper. If the paper is still jammed in the fuser, 
    turn the green knob on the back of the fuser to remove it.
     
    						
    							Troubleshooting355
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    10. Lower the fuser unit into the printer making sure that the 
    guide posts slide into the holes on the bottom of the unit.
    11. Turn the handles on both sides of the fuser unit to lock them.
     
    						
    							356Troubleshooting 12. Close covers B and A.
    13. Open the MP tray and reload the paper.
    Jam MP, A (MP tray and cover A)
    Follow the steps below to clear paper jams at the MP tray and 
    cover A.
    1. Remove all paper that is loaded on the MP tray.
     
    						
    							Troubleshooting357
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    2. Gently pull out any sheets of paper that have fed part way 
    into the printer.
    3. Close the MP tray.
    Note:
    Close the expansion trays, if needed, before closing the MP tray.
     
    						
    							358Troubleshooting 4. Push the latch on cover A to the left and open the cover until 
    it stops.
    5. If the optional Duplex Unit is not installed, gently pull out any 
    sheets of paper. Be careful not to tear the jammed paper.
     
    						
    							Troubleshooting359
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    11
    If the optional Duplex Unit is installed, lift up the Duplex Unit. 
    Hold it and gently pull out any sheets of paper. Be careful not 
    to tear the jammed paper.
    w
    Warning:
    Be careful not to touch the fuser, which is marked CAUTION 
    HIGH TEMPERATURE, or the surrounding areas. If the 
    printer has been in use, the fuser and the surrounding areas 
    may be very hot. If you must touch one of these areas, open 
    cover A and B, then wait 30 minutes to allow the heat to 
    subside before doing so.
    6. Close cover A. Then open the MP tray and reload the paper.
    Jam A, C1 (cover A and standard lower paper 
    cassette)
    Follow the steps below to clear paper jams at cover A and the 
    standard lower paper cassette.
     
    						
    							360Troubleshooting 1. Remove all paper that is loaded on the MP tray. 
    2. Close the MP tray. 
    Note:
    Close the expansion trays, if needed, before closing the MP tray.
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C2600DN User Manual