Epson Aculaser CX16 User Manual

P/U Displays the remaining service life of the photoconductor unit as a
percentage.
Note:
The amounts remaining for the supplies status displayed may be different from the actual amounts and
should be used only as reference.
TX/RX RESULT (AcuLaser CX16NF only)
For details, refer to the Facsimile User’s Guide.
REPORT
The machine settings, lists and reports can be printed.
These reports can only be printed from Tray 1.
TX RESULT REPORT
(AcuLaser CX16NF only)Prints the results of fax transmissions. For...

Configuration Menu Overview
To display the settings menu for this machine, select UTILITY in the main screen, and then press the
Select key. From the UTILITY menu, settings for the various machine functions can be changed.
UTILITY Menu
From this menu, various machine settings can be changed.
Note:
❏To return to the previous screen in the UTILITY menu, press the Back key. (If the Back key is pressed
while settings are being specified, those settings are not saved.)
❏T h e  A D M I N .  M A N A G E M E N T...

KEY SPEED TIME TO START Setting
0.1sec / 0.3sec / 0.5sec / 1.0sec / 1.5sec / 2.0sec / 2.5sec /
3.0sec
Specify the length of time until the cursor begins to move continuously
when a key is held down.
INTERVAL Setting
0.1sec / 0.3sec / 0.5sec / 1.0sec / 1.5sec / 2.0sec / 2.5sec /
3.0sec
Specify the length of time until the cursor continuously moves between
settings or characters.
LANGUAGE Setting
ENGLISH / FRENCH / GERMAN / ITALIAN / SPANISH /
PORTUGUESE / RUSSIAN / CZECH / SLOVAK /
HUNGARIAN / POLISH /...

IMAGE REFRESH Setting
ON / OFF
Use when thin white horizontal lines appear at intervals on images.
Note: 
The IMAGE REFRESH function consumes toner.
DUPLEX SPEED
(AcuLaser CX16NF only)Setting
AUTOMATIC / SPEED / QUALITY
Select the print speed for double-sided printing.
If AUTOMATIC is selected, the print speed is automatically selected.
If SPEED is selected, the print speed has priority; however, the print quality
may decrease.
If QUALITY is selected, the print quality has priority; therefore, the print...

Paper size The available paper sizes differ depending on the setting selected as the media type.
Setting selected as the media type Available paper sizes
PLAIN PAPER
A4 / A5 / B5 / LEGAL / LETTER / G LETTER /
STATEMENT / EXECUTIVE / FOLIO /
OFICIO / G LEGAL / CUSTOM(PLAIN)
THICK1, THICK2
A4 / A5 / B5 / LETTER / G LETTER /
STATEMENT / EXECUTIVE /
CUSTOM(THICK)
LETTERHEAD, LABELS
A4 / A5 / B5 / LETTER / G LETTER /
STATEMENT / EXECUTIVE
ENVELOPE
C6 / DL
POSTCARD The screen for selecting the paper size
does...

REMOTE MONITOR Setting
OFF / ON
Select whether or not setting remote monitor.
If ON is selected, technical support can access the menu mode.
If OFF is selected, technical support cannot access the menu
mode.
Note: 
This setting is for technical support uses. Change the setting
only when it is necessary.
NETWORK
SETTINGTCP/IP Setting
DISABLE / ENABLE
Select the setting for connecting to this machine through a
network.
IP ADDR. SETTING
*1Setting
AUTO / SPECIFY
Set the IP address of this machine on the...

FTP*1Setting
DISABLE / ENABLE
Select whether or not to enable FTP.
SMB
*1Setting
DISABLE / ENABLE
Select whether or not to enable SMB.
BONJOUR
*1Setting
DISABLE / ENABLE
Select whether or not to enable Bonjour.
IPP
*1Setting
DISABLE / ENABLE
Select whether or not to enable IPP.
SLP
*1Setting
DISABLE / ENABLE
Select whether or not to enable SLP.
SNMP
*1Setting
DISABLE / ENABLE
Select whether or not to enable SNMP.
SPEED/DUPLEX
*1Setting
AUTO / 10BASE-T FULL / 10BASE-T HALF /
100BASE-TX FULL / 100BASE-TX...

E-MAIL SETTING SMTP Setting
DISABLE / ENABLE
Select whether to enable or disable e-mail transmission op-
erations for this machine.
SENDER NAME Specify the name of the E-mail sender (up to 20 characters)
used for network scanning.
The default setting is “EPSON_AL-CX16NF”.
E-MAIL ADDRESS Specify the E-mail address (up to 64 characters) of the E-mail
sender used for network scanning.
The default setting is blank.
DEFAULT SUBJECT Specify the subject (up to 20 characters) of the E-mail mes-
sage used for...

SMTP TIMEOUT Setting 30 to 300 sec (Default: 60 sec)
Select the amount of time (in seconds) until the connection
with the SMTP server times out.
TEXT INSERT Setting
OFF / ON
Select whether or not the specified text is inserted into the
E-mail message.
POP BEFORE
SMTPDISABLE/
ENABLESetting
DISABLE / ENABLE
Select whether or not to enable POP Before SMTP.
If ENABLE is selected, specify the time (between 0 and 60
seconds). The default setting is 5sec.
POP3 SERVER
ADDR.
*2Specify the host name or IP address...

LDAP SETTING DISABLE/ENABLE Setting
DISABLE / ENABLE
Select whether or not to enable the LDAP function.
LDAP SERVER ADDR.
*4Specify the address (up to 64 characters) of the LDAP server.
The default setting is “0.0.0.0”.
LDAP PORT NO.
*4Setting 1 to 65535 (Default: 389)
Specify the port number of the LDAP server.
SSL SETTING
*4Setting
DISABLE / ENABLE
Select whether or not to enable SSL.
SEARCH BASE
*4Specify the search starting point (up to 64 characters) in a
hierarchical structure arranged on the LDAP...