Epson AcuLaser M2400DTN User Manual

							❏Keep all protective materials in case you want to ship the optional paper cassette unit in the
future.
3. Carefully, grasp the printer at the position indicated below and lift it carefully.
4. Align the corners of the printer and the unit, then lower the printer gently onto the unit so that the
connector and two pins on the top of the unit fit into the terminal and the holes on the bottom of
the printer respectively.
Note:
You can install one optional paper cassette unit (Epson AcuLaser M2300/M2310 series) or two
optional paper cassette units (Epson AcuLaser M2400/M2410 series) to the printer. When you
install two units, stack them up against each other, and then place the printer on them.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     61
 
						

							5. Pull the paper cassette out from the unit.
6. Turn the lever to the position as shown below to lock the optional paper cassette unit.
7. Insert the paper cassette back into the unit.
8. Reconnect all the interface cables and the power cord.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     62
 
						

							9. Plug the printer’s power cord into an electrical outlet.
10. Turn on the printer.
To confirm that the option is installed correctly, print a Status Sheet. See “Printing a Status Sheet” on
page 93.
Note for Windows users:
If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See
“Making Optional Settings” on page 117.
Note for Macintosh users:
When you have attached or removed printer options, you need to delete the printer using Print & Fax (for
Mac OS X 10.5 or later) or Print Setup Utility (for Mac OS X 10.4), and then re-register the printer.
Removing the optional paper cassette unit
Perform the installation procedure in reverse.
Memory Module
By installing a Dual In-line Memory Module (DIMM), you can increase printer memory up to 288 MB
(320 MB for the DN models). You may want to add additional memory if you are having difficulty
printing complex graphics.
Installing a memory module
w
Warning:
Be careful when working inside the printer as some components are sharp and may cause injury.
c
Caution:
Before you install a memory module, be sure to discharge any static electricity by touching a
grounded piece of metal. Otherwise, you may damage static-sensitive components.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     63
 
						

							1. Turn the printer off and unplug the power cord.
* OFF
c
Caution:
Make sure to unplug the power cord from the printer to prevent getting an electrical shock.
2. Remove the screw on the option cover on the back of the printer using the screw driver.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     64
 
						

							3. Remove the option cover.
4. Identify the memory slot. The position is shown below.
a. memory slot
5. Push a white stopper until it stops.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     65
 
						

							6. Insert the memory module into the memory slot until it stops.
7. Slide the white stopper back toward you to lock the memory module.
c
Caution:
❏Do not apply too much force.
❏Be sure to insert the memory facing the correct way.
❏Do not remove any modules from the circuit board. Otherwise, the printer will not work.
8. Reattach the option cover.
9. Tighten the screw on the option cover using the screw driver.
10. Reconnect all the interface cables and the power cord.
11. Plug the printer’s power cord into an electrical outlet.
12. Turn on the printer.
To confirm that the option is installed correctly, print a Status Sheet. See “Printing a Status Sheet” on
page 93.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     66
 
						

							Note for Windows users:
If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See
“Making Optional Settings” on page 117.
Note for Macintosh users:
When you have attached or removed printer options, you need to delete the printer using Print & Fax (for
Mac OS X 10.5 or later) or Print Setup Utility (for Mac OS X 10.4), and then re-register the printer.
Removing a memory module
w
Warning:
Be careful when working inside the printer as some components are sharp and may cause injury.
c
Caution:
Before you remove a memory module, be sure to discharge any static electricity by touching a
grounded piece of metal. Otherwise, you may damage static-sensitive components.
Perform the installation procedure in reverse.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Installing Options     67
 
						

							Chapter 4
Replacing Consumable Products/Maintenance Parts
Precautions During Replacement
Always observe the following handling precautions when replacing consumable products or
maintenance parts:
For details about replacement, see the instructions that come with the consumable products or
maintenance parts.
w
Warning:
❏Be careful not to touch the fuser, which is marked CAUTION, or the surrounding areas. If the
printer has been in use, the fuser and surrounding areas may be very hot.
❏Do not dispose of used consumable products or maintenance parts in fire, as they may explode
and cause injury. Dispose of them according to local regulations.
❏Provide enough space for the replacement procedure. You will have to open some parts (such as
the printer cover) of the printer when you are replacing consumable products or maintenance
parts.
❏Do not install the consumable products or maintenance parts that reach end of service life into the
printer.
For details about the handling precautions, see “Handling consumable products and maintenance
parts” on page 15.
Replacement Messages
If a consumable product or maintenance part reaches the end of its service life, the printer displays the
following lights on the panel or the window of EPSON Status Monitor. When this happens, replace the
depleted consumable product or maintenance part.
Note that the toner cartridge supplied with your printer is partly used during the initial setup,
therefore the cartridge prints fewer pages compared to subsequent toner cartridges.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Replacing Consumable Products/Maintenance Parts     68
 
						

							Light pattern Description
Replace Toner
Explanation:
The toner cartridge has reached the end of its service life and need to be replaced.
When the Error light turns on, you cannot continue printing. Replace the toner cartridge with a
new one. See “Replacing Consumable Products/Maintenance Parts” on page 68 for instructions.
Replace Maintenance Unit
Explanation:
The maintenance unit has reached the end of its service life and need to be replaced. 
When the Error light turns on, you cannot continue printing. Replace the maintenance unit with
a new one. See “Replacing Consumable Products/Maintenance Parts” on page 68 for
instructions.
Note:
Error Lights appear for one replacement product at a time. After replacing a replacement product, check
the lights on the panel for other replacement products.
❏The toner cartridge is not an independent unit that you install directly into the printer. The
cartridge needs to be inserted into the developer unit’s casing and then installed into the printer.
w
Warning:
❏Do not touch the toner. Always keep toner away from your eyes. If toner gets on your skin or
clothes, wash it off with soap and water immediately.
❏Keep consumable products and maintenance parts out of the reach of children.
❏Do not dispose of used consumable products or maintenance parts in fire, as they may explode
and cause injury. Dispose of them according to local regulations.
❏If toner is spilled, use a broom and dustpan or a damp cloth with soap and water to clean it up.
Because the fine particles can cause a fire or explosion if they come into contact with a spark, do
not use a vacuum cleaner.
❏Be careful not to touch the fuser, which is marked CAUTION, or surrounding areas. If the
printer has been in use, the fuser and the surrounding areas may be very hot. If you must touch
one of these areas, wait 30 minutes to allow the heat subside before doing so.
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Replacing Consumable Products/Maintenance Parts     69
 
						

							c
Caution:
❏You must completely open the printer cover when replacing the toner cartridge; otherwise, you
may damage the printer.
❏Never touch the developing roller that is exposed after removing the protective cover;
otherwise, print quality may decline.
❏When you replace the toner cartridge, wipe paper dust and marks from the metal roller inside
the printer with a dry and soft cloth as shown below.
* metal roller
Epson AcuLaser M2300/M2310/M2400/M2410 Series     User’s Guide
Replacing Consumable Products/Maintenance Parts     70