Epson P4000 Manual

							Introduction11
1
1
1
1
1
1
1
1
1
1
English❏If you plan to use this product in Germany, the 
building installation must be protected by a 16 
amp circuit breaker to provide adequate 
short-circuit protection and over-current 
protection for this product.
❏Do not use a damaged or frayed AC adapter.
❏If you use an extension cord with this product, 
make sure the total amperage of all devices 
plugged into the extension cord does not exceed 
the cord’s amperage rating.
❏Never disassemble, modify, or attempt to repair 
the AC adapter by yourself except as specifically 
explained in this guide.
❏Do not use power outlets controlled by wall 
switches or automatic timers.
❏Do not use power outlets on the same circuit as 
large motors or other appliances that may cause 
voltage fluctuations.
❏Avoid using outlets on the same circuit as 
photocopies or air control systems that regularly 
switch on and off.❏To prevent fire or electric shock, do not cover the 
AC adapter with a blanket or similar covering.
❏Position this product’s power cord so that it will 
not be stepped on or run over.
❏Do not place any objects on the power cord and 
the AC adapter.
❏Keep the power cord straight at the ends and at 
the points where it enters the transformer.
❏The power cord should be placed to avoid 
abrasions, cuts, fraying, crimping, kinking, and 
other damage.
❏If the AC plug does not fit your outlet, have a 
proper outlet installed by a qualified electrician.
❏Remove the AC plug from the outlet during 
lightning storms.
For US and Canadian users:
Use the included power cord or a 6 to 10 foot 
UL-approved type SPT-2 or heavier type, 2 × 18 AWG 
cord with a 125 V 10 A plug and 125 V 7 A connector. 
						

							12Introduction
When using a memory card
❏Only memory cards designed for the product’s 
specifications can be used.
❏Do not remove a memory card or turn off the 
product while the Access lamp is flashing. See 
“LCD and control panel” on page 16 to find where 
the Access lamp is.
When using the LCD
❏The LCD panel on this product may contain a few 
small bright or dark spots. These are normal and 
do not mean that your LCD panel is damaged in 
any way.
❏If the LCD panel on this product is damaged, 
consult your dealer.
❏If the liquid crystal solution contained in the LCD 
panel on this product leaks out and gets onto your 
hands, wash them thoroughly with soap and 
water. If it gets into your eyes, flush them 
immediately with water. If discomfort or vision 
problems remain after a thorough flushing, see a 
doctor immediately.❏Only use a soft, dry cloth to clean the display. Do 
not use liquid or chemical cleaners.
When storing, maintaining, or transporting 
P-4000
❏Do not store this product outdoors.
❏Do not store this product near water.
❏Do not store this product in a location subject to 
high temperature or humidity.
❏Do not store this product in a location subject to 
rapid changes in temperature or humidity.
❏Do not store this product in a location subject to 
direct sunlight or strong light sources.
❏Unplug this product from the power outlet before 
cleaning it. Use a damp cloth for cleaning and do 
not use liquid or aerosol cleaners. 
						

							Introduction13
1
1
1
1
1
1
1
1
1
1
English❏Remove the battery from and unplug this product 
and refer servicing to qualified service personal 
under the following conditions: The power cord 
or plug is damaged; liquid has entered this 
product or its options; this product or its options 
have been dropped or the case is damaged; this 
product or its options do not operate normally or 
exhibit a distinct change in performance.
Safety information for United Kingdom users
The following safety information applies to the AC 
adapter.
w
Warning:
Refer to the rating plate for the voltage and check that 
the appliance voltage corresponds to the supply 
voltage.
Important:
The wires in the mains lead fitted to this appliance are 
colored in accordance with the following code:
Blue — Neutral
Brown — Live
As the colours of the wires in the mains lead of this appliance 
may not correspond with the coloured markings identifying 
the terminals in your plug, proceed as follows;The blue wire must be connected to the terminal in the plug 
marked with the letter N.
The brown wire must be connected to the terminal in the 
plug marked with the letter L.
If damage occurs to the plug, replace the cord set or consult 
a qualified electrician.
For United Kingdom, Hong Kong, and 
Singapore users
Replace fuses only with fuses of the correct size and 
rating. 
						

							14Getting Started
Chapter 2
Getting Started
Unpacking Your P-4000
Make sure that all of the items shown below were 
included in the box with your P-4000.
* The plug type for the power cable may vary, depending on the 
local standards. P-4000Stand
Carrying caseUSB cable
Strap
Lithium-ion battery
Power cable* AC adapter
User’s Guide (this guide)
Software CD-ROM 
						

							Getting Started15
2
2
2
2
2
2
2
2
2
2
EnglishParts
FrontBack
CF Card slot
Power switch 
with Hold 
function
Control panel LCD SD Card slot
Reset buttonCF Card slot 
eject button
Battery coverA/V Out connector
USB connectorAC adapter 
connector Headphone connector
USB connector 
rubber cover
Speaker 
						

							16Getting Started
LCD and control panel
Print button Press this button to display 
the Print menu.
Menu button Press this button to display 
the pop up menu. For details, 
see “Using the Pop Up 
Menu” on page 49.
Charge  lamp  (Green) On when the battery is being 
charged.
OK button Print button Charge lamp
Cancel button4-way ring
Access lampMenu button
Illumination lamp
Display button
Home button
Access lamp (Orange) Flashes when accessing data 
on the HDD or a memory 
card.
4-way ring
(Up/ Down/Left/Right 
button)Press this button to move the 
cursor or highlight. You can 
select an object by pressing 
this button to the right, left, 
up, or down.
Illumination lamp (Blue) Flashes during such 
operations as turning the 
power on, or during 
printing.
The light also flashes when 
P-4000 is in the LCD 
power-off mode.
OK button Press this button to 
determine the selection and 
proceed to the next step.
Cancel button Press this button to cancel the 
selection and return to the 
previous screen.
Display button Press this button to display 
information, instructions, or 
messages. 
						

							Getting Started17
2
2
2
2
2
2
2
2
2
2
English
Setting Up the P-4000
After unpacking your P-4000, set it up so it is ready to 
use. This section describes how to charge the battery 
and turn the power on and off.
Charging the battery
Installing the battery
1. Slide the battery cover to the left. 
The battery cover opens.2. Insert the battery into the compartment in the 
direction of the arrow on the battery.
3. Close the battery cover and slide it to the right 
until it clicks. Home button Press this button to go back 
to the Home screen.
arrow
BATT. 
						

							18Getting Started
Charging the battery
After installing the battery, charge the battery using 
the AC adapter. 
Note:
The battery status is always displayed at the top right corner 
of the LCD.
1. Make sure that the battery is installed.
c
Caution:
Do not connect the AC adapter when the battery is 
not installed. Doing so may cause P-4000 to be 
damaged.2. Connect the AC adapter to P-4000 as shown below 
and plug the other end into a power outlet.
The Charge lamp is on during charging. When the 
battery is fully charged, the Charge lamp turns off. It 
takes about 3 hours to fully charge the battery when 
P-4000 is off. It takes more when you are operating it.
Note:
P-4000 stops charging, if the battery becomes hot when 
operating it during charging. In that case, it starts charging 
again when it cools down.
: Indicates sufficient battery power.
: Indicates moderate battery power.
: Indicates low battery power.
: Indicates battery power is running out. P-4000 is shut down 
automatically. Charge the battery using the AC adapter.
: Indicates the AC adapter is connected to P-4000. 
						

							Getting Started19
2
2
2
2
2
2
2
2
2
2
EnglishRemoving the battery
1. Make sure that P-4000 is turned off. 
c
Caution:
❏Remove the AC adapter if it is connected to 
P-4000.
❏Never remove the battery while P-4000 is 
turned on. Doing so may cause data in the 
card or HDD to be lost or damaged.
2. Open the battery cover.
3. Push the catch down. 
The battery is pushed out.4. Pull out the battery. Then close the battery cover.
w
Warning:
Do not carry loose batteries in your pockets. 
						

							20Getting Started
Turning the power on
Slide the power switch to   as shown below. The 
power switch will return to the original position.
The illumination lamp turns on.
When you turn on P-4000 the first time, the Language 
setting screen and Date and time settings screen are 
displayed. Follow the instructions below.1. The Language setting screen appears. Select the 
language you want to use with the 4-way ring, 
and press the OK button.
2. The Date and time settings screen appears. Press 
the Right or Left button on the control panel to 
change the value of the selected item.
illumination 
lamp
Italiano Francais
Espanol
Language setting
English (Intl.)
Nederlands
Deutsch
Date and time
Date Format Minute
Hour
Day
Month
Year
2004
Jul
26
13
07
YYYYMMDD