Flir ThermovisionMDSeries Operators Manual

432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 19
 MD-Series System Configuration
Set Symbology Menu
When the Set Symbology option is selected from the main menu, the following on-
screen menu displays.
Disable (Enable) PC Icon and JCU Icon
The display of the PC icon and the JCU icons can be enabled or disabled using 
the first two menu entries. The other  icons on the screen are controlled by 
selecting one of the three settings shown  on the menu: Display All Icons, Display 
Minimal Icons, and...

 MD-Series System Configuration
20432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 
Hide All Icons
None of the icons display permanently, exc ept for the FLIR logo and icons for the 
following special modes:
• Rearview mode enabled
• Freeze video
User Programmable Button
The User Programmable Button only applies when you are using a JCU to 
control the camera. Choosing  this option on the main menu displays the following 
on-screen menu. 
Note: It is also possible to enter this menu by pressing and...

432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 21
 MD-Series System Configuration
System Setup Menu
When you select System Setup from the main menu, the following on-screen 
menu displays. 
Save Camera Settings
This option commands the camera to sa ve the current settings, such as the 
thermal camera polarity, scene, and zoom settings, to the camera’s non-volatile 
memory. The settings will be used wh en the camera power is cycled.
Enable (Disable) Ball-Down Installation
This menu option should be...

 MD-Series System Configuration
22432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 
The possible characters that can be us ed include the letters of the alphabet 
(upper or lower case), the numbers  0-9, and the hyphen (-). When you finish 
entering the name, exit. 
Then confirm the new camera name or cancel and continue making changes. 
When you are finished, select Exit.
About/Help Menu
When you select About/Help from the main menu, the following on-screen menu 
displays.
Video Icon Help Screens...

432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 23
 MD-Series System Configuration
Product Information
Selecting Product Information displays  product information for the MD-Series 
camera you are using, such as the camera model, serial number, and software 
release information. If there are any problem s with the camera, it is useful to have 
this information available when contacting FLIR technical support. An example of 
the display is shown below.
Name: MD-625 
S/N: JD0123
MAC 00:40:7f:40:60:40...

 MD-Series System Configuration
24432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 
Contact FLIR
Selecting Contact FLIR displays the FL IR contact information on the screen. 
Additional contact information is includ ed at the back of this manual. When 
contacting FLIR, please have the product information available.
Restore Factory Defaults
Select Restore Factory Defaults to rest ore the MD-Series to its factory default 
settings. The camera will prompt yo u to confirm before continuing.
Refer to...

432-0010-00-10 Rev 100 MD-Series Operator’s Manual 25
CHAPTER 4IP Communications
The MD-Series camera is a network device that communicates over an Ethernet 
network using the Internet Protocol (IP). When a PC, laptop, or other device such 
as a smartphone or iPad is connected to  the network, it is possible to control 
features of the camera or make configuration changes. Communication to the 
camera can be accomplished using a web browser or a software application, such 
as the FLIR Mobile web app, or...

 IP Communications
26432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 
Web Browser Interface
Camera Discovery via UPnP
The MD-Series camera (and optional JCU) use Universal Plug and Play (UPnP) 
networking protocols to broadcast their presence on the network. UPnP allows 
devices on a network to connect automatic ally, without the need for configuration 
by a network expert, thus simplifying the implementation of networks and the 
installation of computer components. A UPnP-compatible device from any...

432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 27
 IP Communications
Web Browser Login 
When the web page for the camera is first di splayed, it provides a login page and 
prompts for a user name and password. The system is configured with three user 
logins which provide different levels of access to camera settings:
• The  user login allows camera control through the Toolbar functions
• The  expert user has the Toolbar and an additional Settings menu
• The  admin user has Toolbar, Settings, and...

 IP Communications
28432-0010-00-10 Rev 100 — MD-Series Operator’s Manual 
Toolbar Functions
When logged in as user, the Toolbar screen is displayed with the camera control 
features.   
Icon Function Description
Zoom out Clicking this icon causes the thermal camera to digitally  zoom out if it has pr eviously been zoomed in. 
Zoom in Clicking this icon 
causes the thermal camera to 
digitally zoom in to 2X magnification. On the 
MD-625 model, clicking again causes the thermal 
camera to digitally zoom...