Flir ThermovisionMSeries Operators Manual

432-0003-00-10 Rev 150 — M-Series Operator’s Manual 69
 M-Series Reference Information
Model Part NumbersCamera 
Payload
Video 
Format
Thermal 
Video
Low-Light 
Video (DLTV)
Color Video
(DLTV)
Thermal Video
Resolution
Thermal Frame
Refresh Rate
Mech Image
Stabilization
HFoV 
IR Digital 
Zoom
M-324XP432-0003-05-00S Single NTSC Yes No No 320 x 240 

 M-Series Reference Information
70432-0003-00-10 Rev 150 — M-Series Operator’s Manual 
Troubleshooting Tips
This section includes information that may help you with common issues that 
may arise during operation of the M-Series system.
Video not displayed on monitor 
The camera will not display video if it is in standby mode. Power cycle the 
camera and allow the system to complete the boot cycle prior to JCU connection. 
Ensure the JCU is assigned to the camera, the camera ID appears in the JCU...

432-0003-00-10 Rev 150 — M-Series Operator’s Manual 71
 M-Series Reference Information
Noisy image
A noisy image is usually attributed to a cable problem—too long or inferior 
quality—or the cable is picking up electromagnetic interference (EMI) from 
another device. Although coax cable has built-in losses, the longer the cable is or 
the smaller the wire gauge/thickness, the more severe the losses become; and 
the higher the signal frequency, the more pronounced the losses. Unfortunately 
this is one of...

 M-Series Reference Information
72432-0003-00-10 Rev 150 — M-Series Operator’s Manual 
portions of the day. We do not recommend intentionally viewing the sun, but 
looking at the sun will not permanently damage the sensor. In fact the thermal 
imaging camera often provides a considerable advantage over a conventional 
camera in this type of back-lit situation. 
However, the sun may introduce image artifacts that will eventually correct out 
and it may take some time for the camera to recover. The amount...

432-0003-00-10 Rev 150 — M-Series Operator’s Manual 73
 M-Series Reference Information
Reconnect network, now...
Indicates the camera has detected a loopback termination on the Ethernet RJ45 
connector and has reverted to the Factory Default network settings. Remove the 
Ethernet RJ45 loopback termination adapter. The camera will then continue the 
startup process under the Factory Default network configuration (with DHCP 
dynamic IP addressing).
Warming, please wait…
Indicates the camera has detected a...

 M-Series Reference Information
74432-0003-00-10 Rev 150 — M-Series Operator’s Manual 
The RJ45 loopback termination ties pin 1 to pin 3, and pin 2 to pin 6. The other 
pins are not connected.
5 Unused N/A
6 Receive - 2
7 Unused N/A
8 Unused N/A Pin # Signal Tied to pin # 

NOTES 

FLIR Systems, Inc.
CS World Headquarters
FLIR Systems, Inc.
70 Castilian Dr.
Goleta, CA 93117
USA
PH:+ 1 805 964 9797
PH:+ 1 877 773 3547 (Sales)
PH:+ 1 888 747 3547 (Apps)
FX: + 1 805 685 2711
[email protected] 
EUROPE
CS Eurasian Headquarters
FLIR Systems CVS BV
Charles Petitweg 21
4847 NW Teteringen - Breda
Netherlands
PH: + 31 (0) 765 79 41 94
FX: + 31 (0) 765 79 41 99
[email protected]
FLIR Systems, Inc.
Corporate Headquarters
FLIR Systems, Inc.
27700A SW Parkway Ave.
Wilsonville, OR 97070
USA 
PH: + 1 503...