Funai LT8 M40BB User Manual

2EN
PRECAUTIONS
POWER SUPPLY
The main power supply is engaged when the main plug is 
plugged in a 220-240 V~, 50 Hz AC outlet. To operate the 
unit, press [Q(standby-on)] to turn on the unit.
WARNING: LIVE PARTS INSIDE.                      
DO NOT REMOVE ANY SCREWS.CAUTION
1)Do not attempt to open the cabinet. There are no user 
serviceable parts inside. Refer all servicing to qualified 
service personnel.
2)Slots and openings in the cabinet and the sides or 
bottom are provided for ventilation. To...

3EN
INTRODUCTION
A Note about Recycling 
Following information is only for EU-member 
states: 
Following information is only                        
valid EU-member States:                          
Disposal of batteries and/or accumulators Features
• Integrated Digital Terrestrial Tuner (DVB-T)
• EPG (Electronic Programme Guide)
• Stereo Sound System
• On-Screen Display
• Sleep Timer
• Teletext
• TV Screen Mode Selection
• Auto Shut Off
• Parental Lock
• HDMI Input x 3, SCART x 2
• COMPONENT Input
•...

4EN
Contents
PRECAUTIONS .................................................................. 2
INTRODUCTION................................................................. 3
A Note about Recycling  .................................................. 3
Features ........................................................................... 3
Supplied Accessories....................................................... 3
Trademark Information..................................................... 3
Symbols Used in...

5EN
THINGS TO DO FOR THE FIRST TIME
Attaching the Base
You must attach the base to the unit to have it as a table top unit. 
Be sure the front and rear of the base match the proper direction.
To remove the base from this unitUnscrew the Phillips pan screws on step 3. After the screws 
are removed, move the base in the opposite direction as 
shown by arrow B on step 2, then pull the base up toward 
the front of the unit. Be careful not to drop the base when 
you remove it.
Fixing the Unit on Your...

6EN
OPERATING CONTROLS AND FUNCTIONS
All operations described are based on the use of the remote control. Some operations can be carried out using the buttons on the control panel.
Control Panel
1.Q(standby-on) (p. 8)Press to turn on or off (standby) the unit.2.INPUT (p. 12)Press to switch TV or external input mode.3.PROG.K/L (control panel) (p. 12)Press to select the setting on the menu.
Press to select the item you want to adjust in the picture 
control mode.
Press to go to the next page or the...

7EN
Rear Panel
26.(Aerial) input jack (p. 8)Connect an RF coaxial cable (not supplied) to an antenna or 
RF output jack of a cable system.
27.PC-IN (RGB) input jack (p. 10)Connect a VGA cable (not supplied) to the monitor jack of 
a PC.
28.HDMI (HDMI 1 / HDMI 2 / HDMI 3) input jack (p. 8)Connect an HDMI cable (not supplied) to the HDMI 
output jack of an external device.
29.SCART (SCART1 / SCART2) jack (p. 8)Connect a scart cable (not supplied) to the scart jack of an 
external device.
30.COMPONENT...

8EN
PREPARATION FOR USE
Installing the Batteries
1)Open the battery compartment cover.
2)Insert “R6/AA, 1.5V” penlight batteries into battery 
compartment in the direction as indicated by the polarity (+/–) 
markings. Batteries installed with incorrect polarity may damage 
the remote unit.
3)Close the cover.
4)Push the cover on its top side until it clicks in order to fit the 
cover completely to the compartment.
Antenna Connection
1)Connect an RF cable (not supplied) to  (Aerial) input jack 
at the rear...

9EN
[COMPONENT CONNECTION]
RCA component video connection offers better picture quality.
1)Connect the component video output jack (Y, Pb, Pr) of your 
video device and the COMPONENT video (Y, Pb, Pr) input 
jack of this unit. Use an RCA component video cable (not 
supplied).
2)Connect the audio output jack of your device and the 
AUDIO (L/R) input jack of this unit. Use an RCA audio 
cable (not supplied).
[S-VIDEO CONNECTION]
S-Video connection offers good picture quality.
1)Connect the S-Video output...

10EN
[PC CONNECTION]
If you connect this unit and your PC, you can use this unit as a 
computer monitor.
1)Connect the monitor jack of your PC and the PC-IN (RGB) 
jack of this unit. Use a VGA cable with ferrite core (not 
supplied).
2)Connect the audio line out jack of your PC and the PC-IN 
(AUDIO) jack of this unit. Use a mini-plug audio cable (not 
supplied).
Precautions for the connection to other devices:
 Please use the VGA cable that has a ferrite core.
The following signals can be displayed:...

11EN
SETUP FOR USE
Initial Setting
You need to set the followings to use the unit appropriately for the 
first time you turn on the unit.
1)Press [Q(standby-on)] to turn on the unit.
 “Initial Setup” language menu will appear.
2)Press [K / L] repeatedly to select the menu language you 
want, then press [OK].
3)Press [K / L] to select the country you want, then press 
[OK].
 Scan confirmation menu will appear.
4)Press [K / L] to select “Scan”, then press [OK].
 Channel scanning will start...