GE Vivid E9 User Manual

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 94 
Z-Mechanism replacement 
To prepare: 
 Power down the Vivid E9. 
 Disconnect all probes and external I/O cabling. 
 Remove the LCD Rear Cover. 
 Remove the LCD Monitor assembly. 
 Remove the LCD Arm assembly. 
 Remove the Operator Panel, Upper. 
 Remove the Operator Panel, Lower. 
 Remove the Bulkhead Board. 
 Remove the Bulkhead Plate. 
 Remove the Upper Frame Assembly. 
 Remove the Lower Frame Assembly. 
 Remove the XY (Frogleg) Assembly. 
 Remove the XYZ Control Box 
 
 Remove the four screws from the bottom of the Z mechanism: 
 
 Remove these four screws the Z mechanism: 
 
Z-Mechanism 
  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 95 
 Lift Z Mechanism away. 
 
XYZ Control Assembly Replacement 
To prepare: 
 Power down the Vivid E9. 
 Disconnect the Mains Power Cable from the wall outlet. 
 Disconnect all probes and external I/O cabling. 
 Remove the Left Side Cover. 
 Remove the Rear Cover. 
 Remove the Top Cover. 
XYZ Control Assembly removal procedure: 
 Disconnect the cables to the XYZ Control Assembly. 
 Unscrew and remove two (2x) screws. 
 
  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 96 
 Pull the top of the XYZ Control Assembly forwards, up and away 
from the bracket. 
XYZ Control Assembly installation procedure: 
 Thread the XYZ Control Assembly into position. 
  Install the three screws at the top, rear. (M6x16 sunken. Torque: 
9.8 Nm.) 
 Install the two remaining screws on the top. (M4x8, sunken. 
Torque: 4.9 Nm.) 
 4.) Connect the cables to the XYZ Control Assembly. 
 5.) Install the Top Cover. 
 6.) Install the Rear Cover. 
 7.) Install the Left Side Cover. 
Main Power Suppy Replacement 
The Logiq E9 has two types of power supllies the PS Lamba and the 
Cherokee/Mitra. The mounting is the same for both devices but the 
connectors are different. It is possible to replace the fan assembly 
and the 4D Motor Controller (4D MC) motor of the Cherokee/Mitra 
without replacing the entire MPS unit. 
The Vivid E9 power supply does not contain any FRUs and must be 
replaced entirely if it becomes defective. There are several versions 
so be sure to determine the correct part number for your system 
before ordering. 
To prepare for MPS replacement perform the following steps: 
 System Power Down 
 Disconnect all probes and external I/O cabling. 
 Remove both Side Covers. 
 Remove the Top Cover. 
 Remove the Filter Cover. 
  Remove the Rear Cover. 
 Disconnect the battery cable from EPS or CB  
Vivid E9 Main Power Supply Replacement 
Follow these steps to remove the MPS: 
  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 97 
 Disconnect the cables from the top of the power supply. 
 
 Remove the three screws that secure the MPS. 
 Ease the MPS away from the fang bracket. 
 Pull/slide the entire MPS backwards until the connectors to the 
FEP/Backplane are unseated and lift the MPS away. 
Logiq E9 Main Power Supply Replacement 
Follow these steps to remove the MPS: 
Disconnect the MPS cable and all cables from the top of the MPS: 
 AC output to peripherals, printer 
 Power to BEP 
 USB 
Remove the three screws that secure the MPS with a 5 mm Allen 
wrench and ease the MPS away from the fang bracket. 
Carefully pull the entire MPS backwards until the connectors to the 
Card Cage/Backplane are unseated. 
If the 4D Motor Controller option is installed, you will need to 
disconnect the USB Cable from J28 on the BEP. 
To replace the new MPS: 
If needed, remove the 4D 
motor controller from the 
PS and install it in the 
replacement Power Supply 
before procceding  
The 4D MC will also have 
to be transferred to the 
replacement MPS.  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 98 
Make sure the GFI PCIe cable is routed behind the MPS fang as shown 
on the left. This is for the GFI Configuration only. MRX systems do not 
have this cable. 
Slide the MPS forward to seat the connectors on the card cage. 
Engage the tab onto the Fang and install the three screws that secure 
the MPS with a 5 mm Allen wrench (Torque: 10 Nm {7.4 lb-ft}). 
Replace all cables and covers in reverse order of MPS removal 
procedure. 
Back End Processor (BEP) 
There are several versions of the BEP for both systems. Each BEP 
version has internal FRU’s such as :DD, I/O board, Battery Pack. We 
will not cover all permutations in this manual. Please refer to the GE 
parts replacement documentation for correct parts when preparing 
to replace BEP or BEP sub-component parts: 
http://www3.gehealthcare.com/en/Support/Support_Documentation_Library 
 
Logiq E9 Vivid E9 
BEP w/ EPS for R1.x.x and R2.x.x: 
 For GFI configurations. 
 For Phase I and BT 2010 
systems. 
BEP – MRX w/ EPS for R3.x.x: 
 For MRX configurations. 
 For BT 2011 only systems. 
 Not backward compatible. 
 Requires new I/O board. 
 New PCIe cable for MRX. 
BEP for BT’09 (4D): 
 Has same 4D video card as V7. 
 Requires SW v108.0.0 and 
higher. 
BEP for BT’11: 
 BEP without 4D. 
 Requires SW v110.0.0 or 
higher. 
 Optional / new 4D video card 
(NVIDIA FX 1800) to handle 
the 4D feature. 
 
Logiq E9 and. Vivid E9 
BEPs are not compatible 
with each other.  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 99 
 
Logiq BEP replaceables: 
Hard Disk drive HDD 
BEP Power Supply 
EPS Battery Pack 
Vivid BEP replaceables: 
BEP5 power supply 
Hard Disk drive HDD 
Graphics adapter 
Fan 
If the old BEP is a BEP5 with 4D, and the replacement BEP is a BEP6, a 
new Graphics Adapter is needed. 
If the optional DVR Board is present it must be moved over from the 
old to the new BEP. 
To prepare for procedure: 
 Record the system’s TCP=P settings and installed Option strings. 
 Back up the Patient Archive images, Report Archive, User-Defined 
Configuration (Customer Presets), and Service settings. You will 
need to perform a Restore after replacement of the BEP. 
 Raise the top console to its highest position. 
 Power down the system. 
 Disconnect all probes, and external I/O cabling. 
 Remove the left side cover only, unless the top cover is removed 
to increase access to BEP top cables then also remove the right 
side cover. 
 Remove the printer by releasing the two clips holding the printer 
bracket to the top of the BEP and gently sliding the printer 
bracket back towards the center of the system to remove the 
printer bracket. 
Logiq E9 BEP Replacement 
This procedure is for Logiq E9 R4.x and later.  
Patient IO not sold 
separately.  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 100 
If a new battery does not come installed in the replacement BEP FRU, 
transfer the battery into the new BEP. 
1. Disconnect all I/O cables and all cables from the top of the BEP. 
2. Loosen the thumb screws or screws at the top of the BEP cover, or 
the three screws that attach the cover to the BEP. Tilt the top of the 
BEP cover away from the BEP. 
3. All the connectors to the CB (ChargeBoard) must be “unlocked“ in 
order to remove them. Slide the locking latch towards you and pull 
the connector to the left to release. 
Disconnect: 
 The battery cable from PCN1 on the CB (ChargeBoard). 
 The CB to the PB (PowerBoard) cable from PCN2. 
 
Place the BEP cover aside. 
4. Remove the two 5 mm HEX key screws at the inside base of the 
BEP. 
5. Release the lock connector for the BEP to Backplane cable, J2 (left) 
on a MRX Configuration as shown below. 
Note: BEP replacement 
requires a software 
reload. 
Note: You cannot power 
up the unit with the cables 
detached. The system will 
power up without the 
battery pack, but the 
cables on the cover must 
be attached. 
When the Charge Board 
(CB) is exposed first 
remove the battery cable 
and the CB to PB from 
PCN1 on the CB. IF the 
24V from the battery is 
exposed and you drop a 
tool or a screw on the EPS 
or CB, you could short the 
battery and cause 
permanent damage to the 
system.  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 101 
 
 
Or, the Backplane cable, J3 (right) and J5 PCIe to the Card Rack on a 
GFI Configuration, using a BEP6 as shown below. Keep the cable to 
transfer to the replacement BEP. 
 
6. Slide the entire BEP away from the system approximately one inch, 
and finish removing the printer bracket then slide the entire BEP 
chassis out of the system. 
7. You will need to remove the following parts from the BEP, to 
reinstall in the replacement BEP: 
 Option Dongle  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 102 
 Printer Bracket 
 BackPlane to BEP cable 
 Wireless Card and Antennas (if present) 
 Patient I/O (if present) 
 S Video Card (if present) 
Vivid E9 BEP Replacement 
This procedure is for Vivid E9 systems. Follow these steps to remove 
the BEP: 
1. Disconnect all I/O cables. 
2. Disconnect the cables from the top of the BEP. 
3. Unlatch the two latches that clamps the printer bracket to the top 
of the BEP. 
 
4. Tilt the front cover forward just until the column cover stop tabs 
clear and lift the lower column cover. 
5. Push the printer bracket toward the FEP approximately 1.3 cm 
(1/2 inch) to free the 3 tabs from the BEP. Push in the direction of 
the white arrow: 
 
 
6. Remove the BEP cover:  
						

							 GE Logiq E9/Vivid E9 Training Manual 
© 2016 Conquest Imaging 103 
 
Loosen the BEP cover’s fixing screw(s): 
 BEP6 has two finger screws on the top of the BEP Cover. 
 Newer versions of the BEP5 have three Phillips screws, one on 
the top and one on each side of the BEP Cover. 
 Older BEP5 have one finger screw at the top of the BEP cover. 
Tilt the top of the BEP cover away from the BEP and set the cover 
aside. 
7. Remove the Printer Bracket from the BEP. 
8. Remove the two hex key screws at the inside base of the BEP. 
9. Reach inside the BEP and disconnect the Boundary Scan Cable 
from the FEP Backplane Connector. It is available through a cut 
out in the BEP’s rear cover. 
10. Slide the entire BEP out of chassis. 
 
Note: If a DVR broad is installed, remove it from the existing BEP and 
install it in the replacement BEP. 
Note: If 4D is installed:  
If you change from BEP6 to a new BEP6 or from a BEP5 to a new BEP5 
you can move the graphics adapter  
If you remove a BEP5, and the new BEP is a BEP6, you will need to 
order a new BEP6 compatible graphics adapter.