Getnet Router GR-724W User Manual

							24 
 
If you want to go back to previous step, please press ‘Back’ button on the 
bottom of this page. 
 
 
 
 
 
2-3-1 Setup procedure for ‘Cable Modem’: 
 
 
 
Here are descriptions of every setup items: 
 
Host Name (1):     Please input the host name of your computer, this is 
        optional, and only required if your service provider 
            asks you to do so.   
 
MAC address (2):    Please input MAC address of your computer here, if 
your service provider only permits computer with 
certain MAC address to access internet. If you’re 
using the computer which used to connect to 
Internet via cable modem, you can simply press 
‘Clone Mac address’ button to fill the MAC address 
field with the MAC address of your computer. 
 
After you finish with all settings, please click ‘OK’ (3) button; if you 
want to go back to previous menu, click ‘Back’.   
 
2-3-2 Setup procedure for ‘Fixed-IP xDSL’: 
 
NOTE: Some service providers use ‘DHCP’ (Dynamic Host 
Configuration Protocol) to assign IP address to you. In this case, you 
can choose ‘Cable Modem’ as Internet connection type, even you’re 
using another connection type, like xDSL. Also, some cable modem 
uses PPPoE, so you can choose ‘PPPoE xDSL’ for such cable modem 
connection, even you’re using a cable modem. 
1 
2 
3  
						

							25 
 
Here are descriptions of every setup items: 
 
IP address        Please input IP address assigned 
assigned by your    by your service provider. 
Service Provider (1):   
 
Subnet Mask (2):    Please input subnet mask assigned by your service 
provider  
 
DNS address (3):    Please input the IP address of DNS server provided 
by your service provider. 
 
Service Provider    Please input the IP address of DNS server 
Gateway Address (4): provided by your service provider. 
 
 
 
 
 
When you finish with all settings, press ‘OK’ (5); if you want to go back 
to previous menu, click ‘Back’. 
 
 
 
 
 
 
 1 
2 
3 
4 
5 
NOTE: You can choose this Internet connection method if your 
service provider assigns a fixed IP address (also know as static 
address) to you, and not using DHCP or PPPoE protocol. Please 
contact your service provider for further information. 
You must use the addresses provided by your Internet service 
provider, wrong setting value will cause connection problem.    
						

							26 
2-3-3 Setup procedure for ‘PPPoE xDSL’: 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):    Please input user name assigned by your Internet 
service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
Service Name (3):    Please give a name to this Internet service, this is 
optional 
 
MTU (4):    Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
 
Connection       Please select the connection type of Internet 
Type (5):    connection you wish to use (detailed explanation 
listed below). 
 
Idle Time Out (6):    Please input idle time out, (detailed explanation 
listed below). 
 
 1 
2 
4  3 
5 
6 
7  
						

							27 
When you finish with all settings, please click ‘OK’ (7); if you want to go 
back to previous menu, click ‘Back’. 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2-3-4 Setup procedure for ‘PPTP xDSL’: 
 
PPTP xDSL requires two kinds of setting: WAN interface setting (setup 
IP address) and PPTP setting (PPTP user name and password). Here we 
start from WAN interface setting: 
 
 
 
Select the type of how you obtain IP address from your service provider 
here. You can choose ‘Obtain an IP address automatically’ (equal to 
DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (i.e. static IP address).   
MTU - Please use default value if you don’t know what it is, or ask 
your service provider for a proper value. 
 
Connection Type - There are 3 options: ‘Continuous’ - keep internet 
connection alive, do not disconnect, connect on Demand - only 
connects to Internet when there’s a connect attempt, and ‘Manual’ - 
only connects to Internet when ‘Connect’ button on this page is 
pressed, and disconnects when ‘Disconnect button is pressed. 
 
Idle Time Out: Specify the time to shutdown internet connect after no 
internet activity is detected by minute. This option is only available 
when connection type is ‘Connect on Demand’.  
						

							28 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of PPTP settings are correct. Please contact 
your Internet service provider if you don’t know what you should fill in 
these fields. 
 
Now please go to PPTP settings section: 
 
 
 
Here are descriptions of every setup items: 
User Name (1):    Please input user ID (user name) assigned by your 
Internet service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
PPTP    Please input the IP address of PPTP gateway 
Gateway (3):    assigned by your Internet service provider here. 
 
Connection       Please input the connection ID here, this is 
ID (4):     optional and you can leave it blank. 
 
MTU (5):    Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
 
BEZEQ-ISRAEL (6): Setting item ‘BEZEQ-ISRAEL’ is only required to 
Check if you’re using the service provided by 1 
2
3 
4 
5 
6 
7 
9 
8  
						

							29 
BEZEQ network in Israel.  
 
Connection       Please select the connection type of Internet 
type (7):    connection you wish to use, please refer to last 
section for detailed descriptions. 
 
Idle Time        Please input the idle time out of Internet 
Out (8):    connection you wish to use, and refer to last section 
for detailed descriptions. 
 
When you finish with all settings, please click ‘OK (9); if you want to go 
back to previous menu, click ‘Back’. 
 
 
2-3-5 Setup procedure for ‘L2TP xDSL’: 
 
L2TP is another popular connection method for xDSL and other Internet 
connection types, and all required setting items are the same with PPTP 
connection. 
 
Like PPTP, there are two kinds of required setting, we’ll start from ‘WAN 
Interface Settings’: 
 
 
 
Please select the type of how you obtain IP address from your service 
provider here. You can choose ‘Obtain an IP address automatically’ (equal 
to DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (equal to static IP address, please refer to ‘PPPoE 
xDSL’ section above).    
						

							30 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of PPTP settings are correct. Please contact 
your Internet service provider if you don’t know what you should fill in 
these fields. 
 
Now please go to L2TP settings section: 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):     Please input user ID (user name) assigned by your 
     Internet service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
L2TP Gateway (3):    Please input the IP address of PPTP gateway 
assigned by your Internet service provider here. 
 
MTU (4):    Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
 
Connection       Please select the connection type of Internet 
type (5):    connection you wish to use, please refer to last 
section for detailed descriptions. 
 
Idle Time        Please input the idle time out of Internet 
Out (6):    connection you wish to use, and refer to last section 1 
2 
4  3 
5 
7 6  
						

							31 
for detailed descriptions. 
 
When you finish with all settings, please click ‘OK (7); if you want to go 
back to previous menu, click ‘Back’. 
 
 
2-3-6 Setup procedure for ‘Telstra Big Pond’: 
 
 
 
This setting only works when you’re using Telstra big pond’s network 
service in Australia. You need to input: 
User Name (1):     Please input the user name assigned by Telstra. 
 
Password (2):      Please input the password assigned by Telstra. 
 
User decide login      Check this box to choose login 
server manually (3):  server by yourself. 
 
Login Server(4):Please input the IP address of login server here. 
 
When you finish with all settings, click ‘OK (5); if you want to go back to 
previous menu, click ‘Back’. 
 
When all settings are finished, you’ll see the following message displayed 
on your web browser: 
 1
2
3 
4 
5  
						

							32 
 
 
Please click ‘Apply’ button to prepare to restart the router, and you’ll see 
this message: 
 
 
 
Please wait for about 30 seconds, then click ‘OK!’ button. You’ll be back 
to router management interface again, and the router is ready with new 
settings.  
						

							33 
2-4 Basic Setup 
 
In this chapter, you’ll know how to change the time zone, password, and 
remote management settings. Please start your web browser and log onto 
router web management interface, then click ‘General Setup’ button on 
the left, or click ‘General Setup’ link at the upper-right corner of web 
management interface. 
 
 
 
 
 
2-4-1 Time zone and time auto-synchronization 
 
Please follow the following instructions to set time zone and time 
auto-synchronization parameters: 
 
Please click ‘System’ menu on the left of web management interface, then 
click ‘Time Zone’, and the following message will be displayed on your 
web browser: Please select time zone at ‘Set time zone’ drop-down list, 
and input the IP address or host name of time server. If you want to 
enable daylight savings setting, please check ‘Enable Function’ box, and 
set the duration of daylight setting. When you finish, click ‘Apply’. 
You’ll see the following message displayed on web browser: 
 
 
 
Press ‘Continue’ to save the settings made and back to web management 
interface; press ‘Apply’ to save the settings made and restart the router so 
the settings will take effect after it reboots. 
 
HERE!