Getnet Router GR-724W User Manual

							44 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on 
other setup procedures, or click ‘Apply’ to reboot the router so the 
settings will take effect (Please wait for about 30 seconds while router is 
rebooting). 
 
If you want to reset all settings in this page back to previously-saved 
value, please click ‘Cancel’ button. 
 
 
2-5-4 Setup procedure for ‘PPTP’: 
 
PPTP requires two kinds of setting: WAN interface setting (setup IP 
address) and PPTP setting (PPTP user name and password). Here we start 
from WAN interface setting: 
 
 
 
Select the type of how you obtain IP address from your service provider 
here. You can choose ‘Obtain an IP address automatically’ (equal to 
DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (i.e. static IP address) 
 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of PPTP settings are correct. Please contact  
						

							45 
your Internet service provider if you don’t know what you should fill in 
these fields. 
 
Now please go to PPTP settings section: 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):    Please input user ID (user name) assigned by your 
Internet service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
PPTP Gateway (3):   Please input the IP address of PPTP gateway 
assigned by your Internet service provider here. 
 
Connection ID (4):    Please input the connection ID here, this is optional 
and you can leave it blank. 
 
MTU (5):    Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
 
BEZEQ-ISRAEL (6): If you are connecting to the BEZEQ network in 
Israel. Please enable this function. 
 1
2
3 
4 
5 
7 
8 
9
6  
						

							46 
Connection       Please select the connection type of Internet 
type (7):    connection you wish to use, please refer to section 
2-5-3 for detailed descriptions. 
 
Idle Time Out (8):    Please input the idle time out of Internet connection 
you wish to use, and refer to section 2-5-3 for 
detailed descriptions. 
 
When you finish with all settings, please click ‘Apply’ (9) button and the 
following message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on 
other setup procedures, or click ‘Apply’ to reboot the router so the 
settings will take effect (Please wait for about 30 seconds while router is 
rebooting). 
 
If you want to reset all settings in this page back to previously-saved 
value, please click ‘Cancel’ button. 
 
 
2-5-5 Setup procedure for ‘L2TP’: 
 
  1
2
4  3 
5 
7 6 
						

							47 
 
Here are descriptions of every setup items: 
 
User ID (1):    Please input user ID (user name) assigned by your 
Internet service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
L2TP      Please input the IP address of PPTP gateway   
Gateway (3):    assigned by your Internet service provider here. 
 
MTU (4):    Please input the MTU value of your network connection 
here. If you don’t know, you can use default value. 
 
Connection    Please select the connection type of Internet connection 
type (5):    you wish to use, please refer to section 2-5-3 for detailed 
descriptions. 
 
Idle Time      Please input the idle time out of Internet connection 
Out (6):    you wish to use, and refer to section 2-5-3 for detailed 
descriptions. 
 
When you finish with all settings, please click ‘Apply’ (7) button and the 
following message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on 
other setup procedures, or click ‘Apply’ to reboot the router so the 
settings will take effect (Please wait for about 30 seconds while router is 
rebooting). 
  
						

							48 
If you want to reset all settings in this page back to previously-saved 
value, please click ‘Cancel’ button. 
 
 
2-5-6 Setup procedure for ‘Telstra Big Pond’: 
 
 
 
This setting only works when you’re using Telstra big pond’s network 
service in Australia. You need to input: 
 
User Name (1):     Please input the user name assigned by Telstra. 
 
Password (2):      Please input the password assigned by Telstra. 
 
Assign login          Check this box to choose login server by yourself. 
server manually (3):   
 
Server IP Address (4):Please input the IP address of login server here. 
 
When you finish with all settings, click ‘Apply’ (5) button and the 
following message will be displayed on your web browser: 
 1
2
3 
4 
5  
						

							49 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on 
other setup procedures, or click ‘Apply’ to reboot the router so the 
settings will take effect (Please wait for about 30 seconds while router is 
rebooting). 
 
If you want to reset all settings in this page back to previously-saved 
value, please click ‘Cancel’ button. 
 
 
2-5-7 Setup procedure for ‘DNS’: 
 
If you select ‘Dynamic IP’ o r  ‘PPPoE’ as Internet connection method, at 
least one DNS server’s IP address should be assigned automatically. 
However, if you have preferred DNS server, or your service provider 
didn’t assign the IP address of DNS server because of any reason, you can 
input the IP address of DNS server here. 
 
 
 
Here are descriptions of every setup items: 
 1
2 
3 
						

							50 
DNS Address (1):    Please input the IP address of DNS server provided 
by your service provider. 
 
Secondary        Please input the IP address of another DNS 
DNS Address (2):    server provided by your service provider, this is 
optional. 
 
 
 
 
 
 
After you finish with all settings, please click ‘Apply’ (3) button and the 
following message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on 
other setup procedures, or click ‘Apply’ to reboot the router so the 
settings will take effect (Please wait for about 30 seconds while router is 
rebooting). 
 
If you want to reset all settings in this page back to previously-saved 
value, please click ‘Cancel’ button. 
 
 
2-5-8 Setup procedure for ‘DDNS’: 
 
DDNS (Dynamic DNS) is an IP-to-Hostname mapping service for those 
Internet users who don’t have a static (fixed) IP address. It will be a 
problem when such user wants to provide services to other users on 
Internet, because their IP address will vary every time when connected to 
Internet, and other user will not be able to know the IP address they’re 
NOTE: Only IP address can be entered here; DO NOT use the hostname 
of DNS server! (i.e. only numeric characters and dots are accepted) 
 
10.20.30.40……………………………………………………………… Correct 
dns.serviceprovider.com…………………………………………... Incorrect  
						

							51 
using at a certain time. 
 
This router supports DDNS service of several service providers, for 
example: 
 
DynDNS (http://www.dyndns.org
) 
TZO (http://www.tzo.com
) 
 
Please go to one of DDNS service provider’s webpage listed above, and 
get a free DDNS account by the instructions given on their webpage. 
 
 
 
Here are descriptions of every setup items: 
 
Dynamic DNS (1):    If you want to enable DDNS function, please select 
‘Enabled’; otherwise please select ‘Disabled’. 
 
Provider (2):      Select your DDNS service provider here. 
 
Domain Name (3):    Input the domain name you’ve obtained from DDNS 
service provider. 
 
Account /        Input account or email of DDNS registration. 
E-Mail (4):   
 
Password / Key (5):   Input DDNS service password or key. 
 1 
2
3
4
5 
6  
						

							52 
After you finish with all settings, please click ‘Apply’ (6) button and the 
following message will be displayed on your web browser: 
 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on 
other setup procedures, or click ‘Apply’ to reboot the router so the 
settings will take effect (Please wait for about 30 seconds while router is 
rebooting). 
 
If you want to reset all settings in this page back to previously-saved 
value, please click ‘Cancel’ button. 
 
2-5-9 Setup procedure for ‘WISP 
 
You can connect with ISP via the router wirelessly, because the router 
provides WISP connection mode. Click “ Enable “ and “ Select Site 
Survey “ button   
 
Here you will find many Wireless Access Points as follows. To Choose an 
Access Point which you would like connect , then click “Select” button 
and “Done” . 
  
						

							53 
 
Here you will see the Access Point which you select.   
 
Here we provide WEP and PWA-PSK security settings for you to connect 
with ISP (Access Point). If your ISP does not ask you to input the security 
key, please choose “ Disable” and click “ Apply “ to save changes you 
made and restart the broadband router, this requires about 30 seconds and 
the broadband router will stop responding (this is normal and is not 
malfunction). You can reconnect to this broadband router and continue on 
other settings later.