Hitachi Projector CP-WX8650 User Manual

							51
Operating
1.
Using the magnify feature
2.
3.
4.
Press the MAGNIFY ON button on the remote 
control.  
The picture will be magnified, and the MAGNIFY 
dialog will appear on the screen. When the 
MAGNIFY ON button is pressed for the first time 
after the projector is turned on, the picture will be 
zoomed by 1.5 times. On the dialog, triangle marks 
to show each direction will be displayed.
The display magnification of the projector switches in order 
with every press of the MAGNIFY ON button.
  For computer signals, HDMI
TM (RGB) signals, HDBaseTTM signals, 
DisplayPort signals, input signals from the LAN port  
 1.5   times  2 times  3 times  4 times  1 time 
  For video signals, DisplayPort signals, HDBaseT signals, SDI signals, 
or HDMITM signals 
 1.5   times  2 times  1 time 
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor
buttons to shift the magnifying area.
Press the MAGNIFY OFF  button on the remote control to exit magnification.
MAGNIFY 
ON / OFF 
button
• The MAGNIFY dialog will automatically disappear in several seconds 
with no operation. The dialog will appear again if the  MAGNIFY ON button is 
pressed when the dialog has automatically disappeared.
• The magnification is automatically disabled when the displaying signal or its 
display condition is changed.
• While the magnification is active, the keystone distortion condition may vary . It 
will be restored when the magnification is disabled.
• Some horizontal stripes might be visible on the image while magnification is 
active.
• This function is not available in the following cases:  -  A sync signal in the range not supported is input.
-   There is no input signal.
NOTE 
						

							52
Operating
1.Press the SHADE button on the control panel.
The mechanical lens shade closes and the 
screen turns to black. The SHADE indicator on 
the projector blinks in yellow while the shade is 
closed.  
To open the shade and restore the screen, press 
the SHADE button again.
Temporarily shading the screen
• The projector will turn off automatically when the time set up by the 
SHADE TIMER passes 
(88).
• When turning off the power by the normal procedure, the lens shade opens 
automatically. If AC power supply is disconnected while opening or closing the 
lens shade, the moving of the lens shade stops. However, the next time the 
projector is turned on, the lens shade opens again automatically.
NOTE
1.Press the FREEZE button on the remote control.  
The “FREEZE” indication will appear on the screen 
(however, the indication will not appear when 
SILENT is selected for the OSD MESSAGE item in 
the SETUP (
79), and the projector will go into the 
FREEZE mode, which the picture is frozen.
To exit the FREEZE mode and restore the screen to normal, press the 
FREEZE button again. 
Temporarily freezing the screen
►If you wish to have a blank screen while the projector's lamp 
is on, use the lens shade function above or the AV MUTE function (
37). Taking 
any other action may cause the damage on the projector. CAUTION
SHADE
button   SHADE
• The projector automatically exits from the FREEZE mode when some 
control buttons are pressed.
• If the projector continues projecting a still image for a long time, the LCD 
panel might possibly be burned in. Do not leave the projector in the FREEZE 
mode for too long.
• Images might appear degraded when this function is operated, but it is not a 
malfunction. NOTE
FREEZE 
button 
						

							53
Operating
The PbyP / PinP is a function for displaying two different picture signals on a 
screen that is separated into main and sub areas for each signal. 
PbyP (Picture by Picture) / PinP (Picture in Picture)
PbyP 
button
• If the  LAN port is selected when the  PbyP button is pressed, input 
from other port is displayed on the main area.
• When in the PbyP / PinP mode, use the MENU button on the remote control 
or ▲/▼ buttons on the control panel to display the OSD menu.
• 
There are  certain functions that cannot be used when in the PbyP / PinP mode.
• A message will be displayed when buttons that cannot be used are pressed 
(
11 6). However, note that there are certain unusable buttons for which 
messages are not displayed.
• The functions on the OSD menu that cannot be used are displayed in gray 
and cannot be selected. NOTE
Normal mode PbyP mode
main 
area sub 
area
(continued on next page)
PinP mode
Press the PbyP button on the remote control. This acctivates the PbyP mode. 
Then, press the PbyP button again. The projector goes into PinP mode. The 
screen displayed before the  PbyP button was pressed will be displayed as the 
main area. Most of operations are effective for the main area only. Only outputs 
the audio input signal paired with the picture input signal for the main area.   
To quit the PinP mode, press the PbyP button again.
ð ð
main 
area
sub area 
						

							54
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
The position of the main area can be toggled with the ◄/► buttons when the 
setting information is displayed on the screen. The yellow frame and the audio 
mark will move together with it.   Changing the main area
main 
area sub 
areamain  area
sub 
area
The setting information will be appeared for several seconds when the PbyP  / 
PinP function is started. Displays the input information for each area. A yellow 
frame around the main area and an audio mark indicating the audio output will 
also be displayed. The information can be redisplayed with the ◄/► buttons after 
it has been erased.
  
Setting information
main area
sub area
Input information Audio mark
Frame
PbyP mode
PbyP mode
main areasub area
(continued on next page)
main area
PinP mode
sub area
PinP mode
main area sub area
Input information Audio markFrame 
						

							55
Operating
Press any button to select an input port on the remote control or press the 
INPUT button on the control panel. A dialog box to select the input signal for 
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To 
change the signal in the sub area, switch temporarily across to the main area 
with the ◄/► buttons. 
Displaying the same signal on the both areas is not allowed. Refer to the table 
for details on available input signal combinations. Any combinations marked 
with "X" can not be selected.
  
Changing the picture input signal
Sub area
Main area
COMPUTER IN
LAN
HDMI 1
HDMI 2
DisplayPort
HDBaseTSDI (CP-WU8700 only)VIDEO
COMPUTER INX XO OOOO X
LANXXXXXXXX
HDMI 1O XXO XXXO
HDMI 2O XO XO OOO
DisplayPortO XXO XXXO
HDBaseTO XXO XXXO
SDI (CP-WU8700 only)O XXO XXXO
VIDEOX XO OOOO X
main area sub area
• The combined input signals marked with an "O" can be selected and 
displayed in the PbyP / PinP mode even when the port is set to SKIP with the 
SOURCE SKIP on the OPTION menu (
87). 
NOTE
Input signal
PbyP (Picture by Picture) / PinP(Picture in Picture) (continued)
PbyP mode
(continued on next page)
main area
sub area
Input signal
PinP mode 
						

							56
Operating
Using ▲/▼ buttons on the remote control changes the size of main area in 
PbyP mode.
  
Changing the size of main area in PbyP mode
1. Select PinP POSITION in INPUT MENU (
73). 
2. Using ▲/▼ buttons on the remote control changes the position of sub area    
    in PinP mode.
  
Changing the position of sub area in PinP mode
main area
sub area main area
sub area
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
• For some signals, it may not be displayed correctly in the PbyP / PinP 
mode, even if it can be displayed properly in the normal mode.
• PbyP/PinP is unavailable when MANUAL is selected in GEOMETRY 
CORRECTION > EDGE BLENDING > MODE. NOTE
Press the MY BUTTON assigned the PbyP / PinP SWAP (
89). The position of 
the both area is exchanged without any setting change.
  
PbyP /PinP SWAP function
main 
area sub 
area main 
area
sub 
areamain area
sub area main area
sub area
PbyP mode PinP mode
main area
sub areamain area sub area
main areasub area
main area
sub area sub areamain area 
						

							57
Operating
1.To start the MENU, press the MENU button. The MENU you last used (EASY 
or ADVANCED) will appear. EASY MENU has priority to appear just after 
powered on.
Using the menu function
2.(1)  Use the ▲/▼ cursor buttons to select an item to operate. If you want to change it to the ADVANCED 
MENU, select the ADVANCED MENU.
(2)  Use the ◄/► cursor buttons to operate the item.
This projector has the following menus: 
PICTURE, IMAGE,INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, 
SECURITY and EASY MENU. EASY MENU consists of functions often used, and 
the other menus are classifi ed into each purpose and brought together as the 
ADVANCED MENU.
Each of these menus is operated using the same methods. 
While the projector 
is displaying any menu, the  MENU button on the projector works as the cursor 
buttons.  The basic operations of these menus are as follows.
In the EASY MENU
(continued on next page) (1)  Use the ▲/▼ cursor buttons to select a menu.
If you want to change it to the EASY MENU, select 
the EASY MENU.
The items in the menu appear on the right side.
(2)  Press the ► cursor button or ENTER button to  move the cursor to the right side. Then use the 
▲/▼ cursor buttons to select an item to operate and press the ► cursor 
button or ENTER button to progress. The operation menu or dialog of the 
selected item will appear.
(3)  Use the buttons as instructed in the OSD to operate the item.
In the ADVANCED MENU
MENU  
button 
RESET  button
ENTER
 button
Cursor buttons
   SHADE   SHADEINPUT 
button 
						

							58
Operating
Using the menu function (continued)
3.To close the MENU, press the MENU button again or select EXIT and press 
the ◄ cursor button or ENTER button. Even if you do not do anything, the 
dialog will automatically disappear after about 30 seconds.
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
IndicationMeaning
EXITSelecting this word finishes the OSD menu. It's the same as 
pressing the 
MENU button.
RETURN Selecting this word returns the menu to the previous menu.
CANCEL or NO Selecting this word cancels the operation in the present 
menu and returns to the previous menu.
OK or YES Selecting this word executes the prepared function or shifts 
the menu to the next menu.
• Some functions cannot be performed when a certain input port is 
selected, or when a certain input signal is displayed.
• When you want to reset the operation, press  RESET button on the remote 
control during the operation. Note that some items (ex. LANGUAGE, VOLUME) 
cannot be reset.
• In the ADVANCED MENU, when you want to return to the previous display, 
press the ◄ cursor button on the remote control. NOTE 
						

							59
Operating
Using the menu function (continued)
Containing items of  each menu
The items contained in the menus are as below;
MenuItems
EASY MENU  (
60
) ASPECT, KEYSTONE, PERFECT FIT, PICTURE MODE,
 
ECO MODE, INSTALLATION, RESET, FILTER TIME,  
LANGUAGE, ADVANCED MENU, EXIT
PICTURE (
62
) BRIGHTNESS, CONTRAST, COLOR, TINT, SHARPNESS, 
ACTIVE IRIS, PICTURE QUALITY, MY MEMORY
IMAGE  (
66
) ASPECT, OVER SCAN, V POSITION, H POSITION, H PHASE,
 
H SIZE, AUTO ADJUST EXECUTE
INPUT  (
69
) PROGRESSIVE, VIDEO NR, COLOR SPACE,  
VIDEO FORMAT, DIGITAL FORMAT, DIGITAL RANGE, 
COMPUTER IN, FRAME LOCK, RESOLUTION,
 
PbyP/PinP SETUP
SETUP  (
74
)
GEOMETRY CORRECTION, LAMP & FILTER, IMAGE OPTIMIZER,  
PICTURE POSITION, INSTALLATION, STANDBY MODE, 
COLOR UNIFORMITY, OSD MESSAGE
AUDIO  (
80
) VOLUME, SPEAKER, AUDIO SOURCE
SCREEN (
81
) LANGUAGE, MENU POSITION, BLANK, AUTO BLANK, 
START UP, MyScreen, MyScreen Lock, SOURCE NAME, 
TEMPLATE, C.C.
OPTION  (
87
) SOURCE SKIP, AUTO SEARCH, DIRECT POWER ON,
 
AUTO POWER OFF, SHADE TIMER, MY BUTTON, 
SCHEDULE, SERVICE
NETWORK  (
100
) PROJECTOR NAME, WIRELESS SETUP, WIRED SETUP, 
NETWORK INFORMATION, SNTP SETUP, MY IMAGE,
 
EXTERNAL CONTROL, PRESENTATION, WIRED NETWORK
SECURITY  (
101
) ENTER PASSWORD, SECURITY PASSWORD CHANGE, 
MyScreen PASSWORD, PIN LOCK, TRANSITION DETECTOR, 
MY TEXT PASSWORD, MY TEXT DISPLAY, MY TEXT WRITING, 
 
SECURITY INDICATOR, STACK LOCK 
						

							60
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons. Then 
perform it according to the following table.
ItemDescription
ASPECT Using the ◄/► buttons switches the mode for aspect ratio.
See the ASPECT item in IMAGE menu (

66
).
KEYSTONE  Pressing the ► button displays the KEYSTONE dialog.  
See the KEYSTONE item in SETUP menu (
74
).
PERFECT FITPressing the ► button displays the PERFECT FIT dialog.  
See the PERFECT FIT item in SETUP menu ( 74
).
PICTURE MODE Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR TEMP 
settings. Choose a suitable mode according to the projected source.
STANDARD   ó  NATURAL  
ó  CINEMA  
ó  DYNAMIC
                                                                                  

USER-3                                                            BOARD(BLACK)
        
                                                                          

USER-2                                                            BOARD(GREEN)
        
                                                                          

USER-1    ó  DICOM SIM. 
ó DAYTIME 
ó WHITEBOARD
• Lines or other noise might appear on the screen when this function 
is operated, but it is not a malfunction.
• DICOM SIM. is the projector's DICOM
® ("Digital Imaging and 
Communication in Medicine") simulation mode. This mode 
simulates the DICOM standard, which is a standard applicable to 
digital communications in medicine, and can be useful for displaying 
medical images, such as X-rays photos. This projector is not a 
medical device and is not compliant to the DICOM standard, and 
neither the projector nor the DICOM SIM. mode should be used for 
medical diagnosis.
(continued on next page)