Honeywell 1900ghd-2 User Manual

3 - 1
3
Cordless System Operation
Note: This chapter applies only to cordless scanning systems.  It does not apply to corded scanners. 
How the Cordless Charge Base/Access Point Works
A cordless charge base or an Access Point provide the link between the cordless scanner and the host system.  The base/
Access Point contains an interface assembly and an RF communication module.  The RF communication module performs the 
data exchange between the cordless scanner and the interface assembly.  The control...

3 - 2
Scan the linking bar code on the top of the Access Point to establish a connection between the 
Access Point and the scanner.  The scanner emits a short beep and flashes the green LED to 
confirm a connection with the Access Point.  The Access Point’s Page button remains blue.
Replacing a Linked Scanner
If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner 
bar code below with a new scanner and place that scanner in the base,...

3 - 3
Programming the Scanner and Base or Access Point
When using the scanner and charge base or Access Point together as a system, menu parameters and configuration settings 
are stored in the charge base or Access Point.  Therefore, when programming any menu configuration settings, the scanner 
must be linked to the intended charge base or Access Point.
Note: This only applies when the scanner is linked to a charge base or Access Point.  If the scanner is in a non-base mode, 
configuration settings are...

3 - 4
Page Button
When you press the Page button on the base or Access Point, the scanners associated with that base or Access Point will begin 
beeping (3 short and 1 long beep).  If you pull the trigger on a scanner that is beeping in response, or press the Page button on 
the base or Access Point a second time, all associated scanners will stop beeping.  See Pagingon page 3-7 for further informa-
tion about Page Button settings. 
Note: If you are using a Xenon 1902HC model, refer to Page Button and...

3 - 5
Proper Disposal of the Battery
When the battery has reached the end of its useful life, the battery should be disposed of by a qualified 
recycler or hazardous materials handler.  Do not incinerate the battery or dispose of the battery with gen-
eral waste materials.  You may send the scanner’s battery to us. (postage paid).  The shipper is responsi-
ble for complying with all federal, state, and local laws and regulations related to the packing, labeling, 
manifesting, and shipping of spent...

3 - 6
Base Power Communication Indicator
To display the power indicator on a base or an Access Point, scan the Base Power Communication Indicator On bar 
code.  To turn off the power indicator, scan the Off bar code.  Default = On.  
Reset Scanner
Scanning this bar code reboots the scanner and causes it to relink with the base or Access Point.
Scanning While in Base Cradle
Note: This feature only applies to the CCB01-010BT base.
If you want to be able to scan bar codes while the scanner is in the base...

3 - 7
When Base Charge Off is selected, the scanner battery does not charge when the scanner is in the base cradle.
When External or Interface Cable Power is selected, the scanner battery charges from the base’s external power supply, if 
there is one.  If there is no external power supply to the base, the scanner battery charges from the interface cable.  
When External Power Only is selected, the scanner battery only charges from the base’s external power supply.  If there is no 
external power supply,...

3 - 8
Paging Pitch
When you press the Page button on the base or Access Point, the scanners associated with that base or Access Point will 
begin beeping (see Page Button on page 3-4).  You can set the pitch of the paging beep for each scanner by scanning one 
of the following bar codes.  Default = Low.
Error Indicators
Beeper Pitch - Base Error
Note: This feature only applies to the CCB01-010BT base.
The CCB01-010BT base can be configured to beep at a particular pitch when an error occurs, such as...

3 - 9
The number of beeps and LED flashes emitted by the CCB01-010BT base for an error condition can be programmed from 
1 - 9.  For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in 
response to an error.  To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code 
and the Save bar code on the Programming Chart inside the back cover of this manual.  Default = 1.
Scanner Report
Scan the bar code...

3 - 10
If you want to charge a scanner and link to the base, use Charge and Link Mode.  If the base is programmed for Charge 
Only Mode, you must link a scanner to it first in order to program it for Charge and Link Mode.  Scan the linking bar code on 
the base to link the scanner, then scan Charge and Link Mode.  Default = Charge and Link Mode. 
Linked Modes
Locked Link Mode and Open Link Mode are the link modes that accommodate different applications.  Scan the appropriate 
bar codes included in the...