Honeywell 8 Channel Dvr Manual

HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B21
08/10
Typical System Setup
Figure 1-1 Typical System Setup 

22 Introduction 

Document 800-06847 Rev B23
08/10
2
Installation
Front Panel Description
Figure 2-1 Front Panel
Table 2-1 Front Panel Description
Group Function Description
AUSB Port Connect USB mouse or USB backup device
BStatus LED Power/Recording (including 
pre-recording)/Network/Alarm
CPOWER Turn ON/OFF the system power
DCursor Keys Allow you to navigate through the menus
Increases reverse playback speed
Zoom - for controlling PTZ cameras
Starts reverse playback
Pauses playback
Parameter for PTZ cameras
Starts...

24 Installation
ENTER Apply or Select an item
Set a PTZ camera
RETURNCancel or go to previous menu
EChannel 
Selection 
ButtonsUsed to display individual channels in live display and 
playback. Also used to enter numeric passwords for 
the various login screens. 
FPTZSelects PTZ mode in live display
GOTO for controlling PTZ cameras
MENUDisplays the Setup menus
SEARCHDisplays the Search menu
Preset - for controlling PTZ cameras
BACKUPDisplays the Archive menu
Preset + for controlling PTZ cameras...

HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B25
08/10
Rear Panel Description
Figure 2-2 Rear Panel
Table 2-2 Rear Panel Description
Group Name Description
A CAMERA 
INPUTSConnect up to 4/8/16 camera inputs (depending on 
your model). 
BMONITORMain BNC monitor.
SPOT OUTBNC spot monitor.
CAUDIO 
INPUTS/
OUTPUTSUp to 4 audio inputs and one audio output can be 
connected.
DPAL/NTSC 
SwitchChange the camera input type.
EALARM 
INPUTSUp to four alarm inputs can be connected and...

26 Installation
Remote Control
Figure 2-3 Remote Control Description
NoteIf there are several co-located DVRs, each DVR must be set with a different ID. 
Using the remote control, you can set an ID for each DVR. Then all DVRs can 
be controlled with one remote control. 
POWER
System power 
On/Off
ID button
Select DVR ID
RETURN
Cancel/Deselect 
Previous screenSETUP
Open System Setup menu
Channel selection buttons
AUDIO
Not supported
ENTER
Apply/Select/Go to next screen
Navigation Buttons
Used for playback...

HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B27
08/10
Setting the DVR ID Using the Remote Control
1. Press the ID button on the remote control.
An Input ID message displays.
2. Press the Set ID, then press RETURN. 
Returning to the Original ID Settings
1. Press the ID button again.
2. Enter 255, then press the RETURN button on the remote control.
DVR Operation
Making the connections
Connect:
• up to 16 camera inputs (DVR model dependent)
• monitors to the DVR using the Composite...

28 Installation
Figure 2-4 Startup Screen
The DVR startup screen detects and checks the status of the hard drives and the 
CDRW/DVD-RW drive. 
Logging On
After startup diagnostics are complete, you must log onto the system. The default user 
name is ADMIN.
Figure 2-5 Log On Screen
Enter the default password 1234 using the channel selection buttons, then press ENTER.
The DVR begins normal operation and shows the default display of 4, 8, or 16 channels 
(depending on your DVR model). 

HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B29
08/10
Figure 2-6 Default Display
Navigating the Default Display
The control bar at the bottom of the screen when the DVR is first turned on. After that, it will 
show the current time and date.
Each channel has a title. 
The red square and letter C in the top right corner of each channel display indicates that 
the channel is in Continuous recording mode.
Control Bar
All menus can be controlled with the Control bar, using either the...

30 Installation
Live Display
Configuring the Screen Division
1. Navigate to DISPLAY  in the Control bar, then click  . 
The Display popup menu appears.
Figure 2-8 Display Popup Menu
2. Select the screen division (1, 4, 6, 8, 9, 16, or a rotation sequence) from the popup 
menu.
Sequencing the Channels
Click SEQ   in the display popup menu. 
Each channel is shown in full screen for a set period of time before switching to the next 
channel in the sequence. 
Click   again to stop the sequence on that...