Honeywell Accenta 8 User Manual
Here you can view all the pages of manual Honeywell Accenta 8 User Manual. The Honeywell manuals for Alarm system are available online for free. You can easily download all the documents as PDF.
Page 1
Engineer’s Manual
Honeywell Security
Accenta/Optima
0
123456789SetResetPAProg Omit Chime
Powe r Day
8EP417A - Accenta LCD keypad
0123456789CHIMEOMITRESETPROGSET
1
23 45
67
8ZONE
Accenta +TAPA D AY
POWER
PA
8EP416 - Accenta LED keypad
8EP396A Optima compact panel
with built-in LED keypad
mini
Zones
mini
8SP399A - Accenta mini panel with
remote LCD keypad and communicator outputs.
8SP400A - Accenta mini panel...
Page 2
Page 3
Accenta/Optima Engineer’s ManualTable of Contents i Contents Introduction............................................................................................................ 1 Features.................................................................................................................. 1 Installation Design................................................................................................ 2 Fixing the Control Panel...
Page 4
Accenta/Optima Engineer’s ManualTable of Contents ii Menu Options ....................................................................................................... 18 0 = Walk Test ....................................................................................................................... 1 8 1 = Alarm Test ..................................................................................................................... 1 9 2 = Test...
Page 5
Accenta/Optima Engineer’s Manual 1 Introduction This manual provides information on Installation design, panel fixing, wiring, power up and programming of the intruder panels. Features „8 zones programmable for Security, 2 zones for Fire. „PA input. „Tamper input. „Outputs for External Siren (Bell) and Strobe. „4 Access level Codes, User 1, User 2, Engineer and Duress, all programmable. „3 fully selectable part set programs. „Chime on any security zone. „250 event memory (LCD Keypad), 8 event memory (LED...
Page 6
Accenta/Optima Engineer’s Manual 2 Installation Installation Design The purchase of this alarm system represents a major step forward in the protection of the property and its occupants. It is important to plan the installation before proceeding following the procedures and advice contained in this manual. Plan the position of each part of the alarm system and the cable runs. Detectors should be sited with particular regard to the degree of coverage required. All of the system wiring is connected...
Page 7
Accenta/Optima Engineer’s Manual 3 Fixing the Control Panel CAUTION:When positioning the control panel make sure that it is located in a dry place away from damp areas. NOTE:The Accenta mini enclosure is illustrated here, however the procedures for the other panels is similar. Control Panel 2. Disconnect the transformer wires from the board, these are marked AC. Carefully remove the board by gently pushing downthe holding clips on the bottom edge of the board and withdraw it from the base. NOTE:...
Page 8
Accenta/Optima Engineer’s Manual 4 PCB There are four fuses mounted on the circuit board, all are 20mm anti-surge. F1 1.6A - to protect the positive (+Ve) line of 12V battery F2 1A - to protect the Speaker 13V supply F3 1A - to protect the Siren (Bell) & Strobe supply F4 1A - to protect the RKP 13V supply As supplied, wire links are fitted across the PA and Tamper terminals to represent a closed circuit. Wiring the System CAUTION:Always power down the panel when wiring external circuits to prevent damage...
Page 9
Accenta/Optima Engineer’s Manual 5 Figure 5. Connecting LED keypads to panel Connecting Keypads Connecting Remote Keypads NOTE:Where an Accenta or Accenta mini panel is being installed, make sure there is at least one remote keypad wired to the panel before the first power up. Up to four remote Accenta LCD or LED keypads can be connected to the panel. Wire the keypad(s) as per Figure 5 (LED keypad) or Figure 6 (LCD keypad). NOTE:When the panel back-up battery is charging, the LCD keypad backlight may not...
Page 10
Accenta/Optima Engineer’s Manual 6 Security Zones It is recommended that no more than 10 magnetic contacts are connected to the same zone and that the combined cable length for each zone does not exceed 100 metres. Figure 7. Security Zone Wiring Fitting the Remote Keypad 1 Separate the RKP baseplate from the main assembly by slackening the retaining screw. 2 Cut away the required thin wall sections around the edges of the baseplate for cable entry. 3 The baseplate mounting holes are 60 mm centres (LED...