Honeywell control panel LYNX Touch 5100 User Manual

							– 81 – 
SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS 
 
Zone Status Icons 
The following icons may be displayed on the Zone Status screen. ICON  DEFINITION 
 ICON  DEFINITION 
 
Alarm  
 
Trouble (red) 
 
Fault (Yellow)  
 
Bypass 
 
Ready    
      
LED Meanings 
Armed LED (Red):  ON = System armed 
 
OFF = System disarmed 
  Blinking = System armed, but a fault exists or alternating with Ready LED 
when AVM (VOX or Talk) or speaker phone mode is active. 
 Ready LED (Green):  ON = System disarmed, ready to arm 
  Blinking = System disarmed, not ready to arm (a fault exists) or alternating  with Armed LED when AVM (VOX or Talk) or speakerphone mode is active. 
Note:  When the system is armed, the Ready LED turns off.  
						

							– 82 – 
REGULATORY AGENCY STATEMENTS 
    
Federal Communications Commission (FCC) Part 15 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or Users Manual.  Unauthorized changes or modifications could void the users authority to operate the equipment. 
CLASS B DIGITAL DEVICE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installatio n. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not  occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  following measures: 
• Reorient or relocate the receiving antenna. •  Increase the separation between the equipment and receiver. •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •  Consult the dealer or an experienced radio/TV technician for help. 
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil num érique de la classe B est conforme  à la norme NMB-003 du Canada. 
Industry Canada (IC)  
This device complies with Part 15 of FCC Rules and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 
Cet appareil est conforme à la partie 15 des rè gles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception ind ésirable.  
						

							– 83 – 
REGULATORY AGENCY STATEMENTS 
  
TELEPHONE/MODEM INTERFACE 
Federal Communications Commission (FCC)  Part 68 
This equipment complies with Part 68 of the FCC rules.  On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN).  You must provide this information to the telephone company when requested. 
This equipment uses the following USOC jack: RJ31X 
This equipment may not be used on telephone-company-provided coin service.  Connection to party lines is subject to state tarif fs.  This equipment is hearing-aid compatible. 
Industry Canada NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user ’s satisfaction. 
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. 
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations  made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment. 
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas. 
Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as appropriate. 
AVIS: l’é tiquette d ’Industrie Canada identifie le mat ériel homologué . Cette étiquette certifie que le mat ériel est conforme aux normes de protection, d’exploitation et de s écurité des r éseaux de t élécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au mat ériel terminal. Le Ministère n’assure toutefois pas que le mat ériel fonctionnera à la satisfaction de l ’utilisateur. 
Avant d’installer ce mat ériel, l’utilisateur doit s ’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télé communication. Le mat ériel doit également être installé en suivant une m éthode accept ée da raccordement. L’abonné  ne doit pas oublier qu’il est possible que la conformit é aux conditions énoncées ci-dessus n ’empêche pas la d égradation du service dans certaines situations.  
Les réparations de mat ériel nomologué doivent ê tre coordonnées par un repré sentant désign é par le fournisseur. L’entreprise de télé communications peut demander  à l’utilisateur da débrancher un appareil  à la suite de réparations ou de modifications effectuées par l ’utilisateur ou à  cause de mauvais fonctionnement.  
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’ energie électrique, de lignes téléphoniques et des canalisations d ’eau métalliques, s ’il y en a, sont raccordé s ensemble. Cette précaution est particuli èrement importante dans les r égions rurales. 
Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-m ême; il doit avoir racours à un service d’inspection des installations  électriques, ou à un électricien, selon le cas. 
Ringer Equivalence Number Notice: The Ringer Equivalence Number  (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.  The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 
AVIS : L’indice d’équivalence de la sonnerie  (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent  être raccord és à une interface. La terminaison d’ une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d ’indices d’équivalence de la sonnerie de tous les dispositifs n ’excède pas 5.   
! 
RF Exposure WARNING: The LYNX Touch must be installed to provide a separation distance of at least 7.8 in (20 cm) from 
all persons and not co-located or operated in conjunction with any other transmitter
. 
  
						

							– 84 – 
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS 
In the event of telephone operational problems, disconnect the control by removing the plug from the 
RJ31X (CA38A in Canada) telephone wall jack. We recommend that your certified installer 
demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone 
connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the 
regular phone works correctly after the control/communicator has been disconnected from the phone 
lines, the control/communicator has a problem and should be returned for repair. If upon disconnection 
of the control/communicator, there is still a problem on the line, notify the telephone company that they 
have a problem and request prompt repair service. The user may not under any circumstances (in or 
out of warranty) attempt any service or repairs to the system. It must be returned to the factory or an 
authorized service agency for all repairs.  
						

							– 85 – 
OWNERS INSURANCE PREMIUM CREDIT REQUEST 
This form should be completed and forwarded to your homeowners insurance carrier for possible premium credit.  
A. GENERAL INFORMATION: 
Insureds Name and Address:    
   
 
Insurance Company: Policy No.:     LYNX Touch Series _________________________________________________  Other   
Type of Alarm:         Burglary       Fire        Both 
  Installed by:      Serviced by:    Name  Name 
       Address  Address  
B. NOTIFIES (Insert B = Burglary, F = Fire) 
Local Sounding Device     Police Dept.    Fire Dept.    
Central Station        Name: ________________________________________________________________________\
_______  
 Address:     Phone:     
C. POWERED BY:  A.C. With Rechargeable Power Supply  
D. TESTING:        Quarterly         Monthly         Weekly        Other  
 
(continued on other side)  
						

							– 86 – 
OWNERS INSURANCE PREMIUM CREDIT REQUEST (cont.) 
 
E. SMOKE DETECTOR LOCATIONS 
      Furnace Room       Kitchen         Bedrooms          Attic  
      Basement            Living Room         Dining Room          Hall  
 
F. BURGLARY DETECTING DEVICE LOCATIONS:  
      Front Door          Basement Door          Rear Door         All Exterior Doors 
       1st Floor Windows         All Windows          Interior Locations 
       All Accessible Openings, Including Skylights, Air Conditioners and Vents 
 
G. ADDITIONAL PERTINENT INFORMATION:    
  
  
  
  
 
 
 
 
 
Signature:         Date:    
  
						

							– 87 – 
 
SERVICING INFORMATION 
Your local Honeywell dealer is the person best qualified to service your alarm 
system. Arranging some kind of regular service program with him is 
advisable.  
Your local Honeywell dealer is: 
Name:  
Address:  
  
Phone:        
 
  
						

							– 88 – 
WARNING!   
THE LIMITATIONS OF THIS ALARM SYSTEM 
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: 
  Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. 
  Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. 
  Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. 
  A user may not be able to reach a panic or emergency button quickly enough. 
  While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate  or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. 
  Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can decrease.   Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the othe r side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. 
  Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. 
  Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. 
  This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to las t as long as 10 years, the electronic components could fail at any time. 
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insuran ce. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. 
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to  learn about these developments. 
   
  
						

							– 89 – 
–     NOTES –  
						

							– 90 – 
–     NOTES –