Honeywell control panel LYNX Touch User Manual

– 51  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Scheduling User Interface  Ready To Arm
23
1
5 6
4
0 8 9
7
Clear
5000-100-147-V0
AM / PM
Enter Time
10:21    AM
Done
  10. If Auto Stay is selected, select “
Clear” then 
enter a 4-digit time on the displayed keypad 
then select “ Save”. If “ Output ” is selected 
proceed to Step 11. If “ Disarm Notification” 
is selected proceed to Step 12. 
11. Select a Device (Device 1 through Device  16). 
12. Enter a Start Time and End Time...

– 52  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Reminders 
The Reminder Feature can be used to program/record reminders that can be displayed on the 
touchscreen, announced by the control and/or sent to one ort two pre-programmed phone 
number(s). Check with your installer to see if the latter feature has been programmed on 
your control. 
Programming a Reminder 
Arm Away
Ready To Arm
Arm Stay
Back
DelaySettings
10:18 AM  June 8,  20105000-100-007-V0
Tools
  1. With the system...

– 53  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Reminders  
Ready To Arm
5000-100-178-V0
Edit
No items to display!
Delete
Add New
  4. Select 
“Add New ”. The system displays the 
Reminder programming screen.  
 
Ready To Arm
Save
5000-100-176-V0
Name FrequencyNone
VoiceNoAcknowledgeNo
 
Ready To Arm
5000-100-180-V0
A
Q
Z
S
W
L
OP
M
K
I
N J
U	
V
G
T
B
H
Y
C F
R
X D
E
Clear
Done
123!@#
abc...
 5. Select 
“Name ”. Enter a name for the 
scheduled function on the displayed keypad...

– 54  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Reminders 
Ready To Arm
Save
5000-100-183-V0
Start Time3:00 PM
DateJanuary 1, 2011
FrequencyOnceNameWalk Dog
VoiceNoFollow MeDisabledAcknowledgeNo
 10. If  a 
“Follow Me ” phone number(s) was 
programmed by your installer you can send 
a reminder to the phone number(s). Select 
“ Follow Me ” option. The system toggles 
between  “Disabled ”,  “To Ph. 1 ”,  “To Ph. 2 ” 
and  “To Ph. 1 & 2 ”, as applicable. 
Note:  For important...

– 55  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Speaker Phone Feature  
If this feature has been programmed the LYNX Touch is capable of operating as a speaker 
phone. During speaker phone operation the system will provide the following functions: 
•  All function/event processing will continue to operate, but there will be no 
announcements. 
NOTE:   The system will enter the Speaker Phone mode even if an alarm or trouble is stored in the system 
memory. 
 
! 
    
Do not use...

– 56  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Speaker Phone Feature 
Placing a Call  
Zones
Arm Away
Ready To Arm
Arm Stay
More
DelayPhone
10:18 AM  June 8,  20105000-100-006-V0
Message
System
  1.  With the system in the disarmed or armed 
state, select the  “Phone ” icon from the 
Home Screen. The system displays the 
Keypad screen. 
 
Ready To Arm
Talk 23
1
5 6
4
0 8 9
7
5000-100-148-V0
Flash
Redial
Volume
  2. Select the 
“Talk ” icon and then enter the 
number you wish...

– 57  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Remote Phone Control Feature 
The LYNX Touch Series is equipped with a remote interactive phone capability that permits 
access to the security system from any off-site touch-tone telephone using all user codes. The 
system will provide the appropriate voice messages and any system beeping sounds 
indicating the status of the security system over the phone line. (Refer to Summary of 
Audible Notification for further information.)...

– 58  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Remote Phone Control Feature 
 
Remote Phone Control Commands 
Enter User Code (within eight seconds). Upon entering remote phone control mode the Lynx will 
announce  “System, enter code ”. 
To remotely disarm system: ........................................................... User Code + [1] 
To remotely arm in AW AY mode: .................................................. User Code + [2] 
To remotely arm in STAY mode:...

– 59  – 
USER FUNCTIONS
USER FUNCTIONS USER FUNCTIONS
USER FUNCTIONS 
    
Remote Services 
 
Your security system may be capable of providing a series of web-based services that allow 
you to communicate with your security system remotely in a number of ways. These services 
provide the ability to: 
•  Access to your security system from a computer via website (Remote Access Feature) 
•   Receive e-mail and text message notification of system events (Multi-Mode Feature) 
•   Perform system functions and...

– 60  – 
FIRE
FIREFIRE FIRE/CO /CO/CO
/CO ALARM SYSTEM  ALARM SYSTEM  ALARM SYSTEM 
 ALARM SYSTEM (If Installed) 
  
 
General Information  
UL
ULUL
UL 
    LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour 
backup battery (P/N LYNXRCHKIT-SHA) is installed.
 
 
General  
Your fire alarm system (if installed) is active 24 hours a day, providing continuous 
protection. In the event of an emergency, the installed smoke, heat and/or carbon monoxide 
detectors will...