Honeywell control panel VISTA32FBPT User Manual

  
– 41 – 
Chime Mode 
Using the   9  Key 
Your system can be  set to alert you to the opening  of a door or window while 
it is disarmed by using CHIME mode. When activated,  three tones will sound 
at the Keypad whenever a protected perimeter door o r window is opened, and 
the  Not  Ready  message  will  be  displayed.  Pressing  t he READY   key  will 
display the open protection points.  
Note that Chime mode can be activated only when the  system is disarmed. 
1.  To turn Chime Mode on,  enter the...

   
– 42 – 
Viewing Alarm Company Messages 
General Information 
Users  of  the  system  may  periodically  receive  messages  on  their  display 
screens from their monitoring agency or installer.  When a message is waiting 
to be viewed, the message shown below will appear.  
MESSAGE. PRESS 0 
FOR 5 SECS. 
1.  Press and hold down   0  key for 5 seconds. 
2.  The message could take up to four screens to dis play all the information 
available. 
NOTE:  Any message sent by the central station downloader...

  
– 43 – 
Panic Keys 
(For Manually Activating Silent and/or Audible Alar ms) 
Using Panic Keys 
Your  system  may  have  been  programmed  to  use  special  key  combinations  to 
manually  activate  panic  functions.  The  functions  th at  might  be  programmed 
are  Silent  Emergency,  Audible  Emergency,  and  Person al  Emergency.  See 
your  installer  for  the  function(s)  that  may  have  be en  programmed  for  your 
system. 
 
Active Panic Functions 
(Your  installer  should  note  which...

   
– 44 – 
Relay Control 
General Information 
Your  system  may  be  set  up  using  a  relay  so  that  a  door  (such  as  in  a  lobby) 
can be unlocked momentarily using a keypad command.   Ask your installer if 
this has been done in our system. 
Executing 
To  activate  the  relay  enter  your  security  code  +  [0 ]  at  the  keypad.    The  door 
will unlock for 2 seconds. 
                          

  
– 45 – 
Using #70 Relay Menu Mode 
General Information 
Your  system  may  be  set  up  so  that  certain  lights  or   other  devices  can  be 
turned on or off by using the #70 command from a ke ypad. Ask your installer 
if this has been done in your system.  
To  activate  relays  from  a  keypad,   enter  4-digit  security  code  +  [#]  +70. 
Follow the keypad prompts described below.  
NOTE:   Your  installer  may  have  restricted  the  use  of  this   function.    Please 
check with your...

   
– 46 – 
Using Schedules 
Delaying the Closing Time 
Your systems programmed schedules may automatically arm the system at a 
predetermined time. In the event a user must stay o n the premises later than 
usual, users with master or manager authority level s can manually delay the 
automatic arming (closing) time up to 2 hours.  To delay the closing time: 
1.  Enter your security code (master or manager auth ority levels only). 
2.  Press the    # 
 key, followed by  82. 
3.  A menu prompt will be...

  
– 47 – 
Using Schedules (cont’d) 
Programming Temporary Schedules 
Temporary  schedules  only  affect  the  partition  from  which  it  is  entered. 
Temporary  schedules  can  be  reused  at  later  dates  si mply  by  scrolling  (by 
pressing  #)  to  the  DAYS?  prompt  (described  below)  a nd  activating  the 
appropriate  days.  This  should  be  considered  when  de fining  daily  time 
windows. Note that only  users with authority level  of manager or higher can 
program temporary schedules....

   
– 48 – 
Using Schedules (cont’d) 
DAYS ?   MTWTFSS 
HIT 0-7  X   X 
This is the prompt that actually activates the  
temporary schedule, and allows the temporary  
schedule to be customized to a particular weeks  
needs. To select the days that are to be activated, 
enter the desired number 1-7 (Monday = 1). An 
X will appear under that day, indicating the 
previously entered schedule for that day is active.  
Entering a days number again will deactivate  
that day.  Pressing 0 will turn all days...

  
– 49 – 
Programming Device Timers 
General Information 
Device  timers  consist  of  an  ON  time  and  an  OFF  time ,  and  selected  days  of 
the week in which they are active. There are up to  20 timers that can be used 
to  control  various  devices,  such  as  lights  or  appli ances.  Your  installer  will 
have  programmed  the  appropriate  devices  into  the  sy stem  (up  to  96  devices 
can be programmed).   
Each  timer  controls  a  single  device  (designated  as  an  output  number)...

   
– 50 – 
Programming Device Timers (cont’d) 
 
00 ON TIME ? 
00:00 PM 
Enter  the  time  you  want  the  device  turned  on  
using  00:01  -  11:59  format.  When  the  display  
shows  the  desired  time,  press  the 
  key  to  move 
to  the  AM/PM  field.  Press  any  key  0-9  to  change  
the AM/PM indication.  
Enter 00:00 if this timer is not being used to turn  
something  ON  for  the  days  selected  below.  (Ex.  
using  one  timer  to  turn  lights  on  one  day  and 
using  another...