Honeywell keypad Tuxedo Touch WiFi User Manual

 
11 
Security 
Introduction to Security System Operation You can arm your system in one of three arming modes: Away, Stay, and Night.  The following table lists the three different 
arming modes and the results of each. 
FEATURES FOR EACH ARMING MODE 
Arming 
Mode FUNCTION Exit 
Delay Entry 
Delay Perimeter 
Armed Interior 
Armed AW AY  
 Press to arm when no one is staying on the 
premises.  When armed in AW AY, the 
system sounds an alarm if a protected door 
or window is opened, or if any movement is...

Security (cont’d) 
12 
can be increased up to 45 seconds at the option of the user by consulting with the installer. Note that emergency, 
carbon monoxide, and fire-type alarms are normally reported without delay.  How to Arm the System
 
Arming the system in any mode is performed in the same way, as described below. 
Note:  Close all perimeter windows and doors before arming. 
Arm the system as follows: 
ICON ACTION  NOTES 
 1. From the “Home” screen, press the 
SECURITY icon. 
 2.  Press the selected...

Security (contd) 
13 
How to Display Faults The Display Faults function is used when you see a “Not Ready Fault” message and want to determine where the fault is and 
what type of fault it is.  To display faults do the following: 
ICON ACTION   NOTES  
  
1. 
From the Security screen, press the 
DISPLAY FAULTS icon.  
 
 A listing of faulted and/or bypassed zones is displayed. 
 
As applicable, take corrective action such as closing a window or door to 
correct the fault.  2.  If the fault cannot be...

Security (cont’d) 
14 
To bypass zones do the following: 
ICON ACTION   NOTES 
 1. From the “Home” screen, press the 
SECURITY icon.   
2. Press the MORE CHOICES icon.   
Note: If any zones are bypassed or faulted, a Display Faults icon is also 
displayed on this screen. 
 3.  Press the SHOW ZONES icon. 
 
While the keypad is requesting and receiving the zone data from the control 
panel, the screen displays Please Wait!. Then the zones, along with their 
current status, are displayed.  
 4. Highlight...

Security (contd) 
15 
To disarm the system when entering the premises: 
The keypad automatically displays the Entry Delay Active screen when you enter the premises: 
ICON ACTION  NOTES 
 
1. Enter your 4-digit user code.  
The partition is disarmed and the Arming screen is displayed showing the 
system as Ready to Arm. 
Note: If you have a commercial system and a time window has been defined 
for when you may disarm the system, the system does not disarm if you are 
outside that time window. 
To disarm...

Security (cont’d) 
16 
To check the status of other partitions perform the following:  
ICON   ACTION  NOTES 
 1. Press the SECURITY icon.   
2. Press the Current Partition icon (lower 
edge of the screen; in this case it displays 
P1 H unless changed by installer).  
 
3.  Enter the code authorized to access other 
partition(s).     If the code is accepted, the system displays the 
partitions that user has access to.   This screen displays the available partitions and their current status.   
The...

Security (contd) 
17 
2. If the keypad does not indicate a READY condition after the second sequence, press the DISPLAY FAULTS icon on the 
Arming screen to display the zone(s) that are faulted.  Be sure to check that smoke detectors/carbon monoxide detectors are 
not responding to smoke, heat, or gas producing objects in their vicinity.  In this case, eliminate the source of heat, smoke or 
leak. 
3. If this does not remedy the problem, there may still be smoke/gas in the detector.  Clear it by fanning...

Security (cont’d) 
18 
How to Enter Console Emulation Mode To access Console Emulation Mode, do the following: 
ICON ACTION  NOTES 
 1. From the Home screen, press the 
SECURITY icon.  
 
2. Press the MORE CHOICES icon.    
 3. Press the CONSOLE MODE icon.   
 Perform functions as you would from a standard alpha keypad. 
How to View the Event Log  Your system has the ability to record various events in a history log wherein each event is recorded with the time and date of its 
occurrence.  The control...

 
19 
Setup 
Setup allows you to make changes to the way your keypad is operating. You may access the Brightness and Volume, Display 
& Audio Setup, IP Setup, System Setup and System Information from the Setup screen.  Brightness and Volume Control From the Home screen, a
ccess the Setup screen as follows: 
ICON ACTION  NOTES 
 1. Press the Setup icon.   
2. Move the Brightness/Volume slide bar up or 
down to increase or decrease settings.  
3. Press the Save icon to save settings. 
If changes are made,...

Setup (cont’d) 
20 
Adjust the Screen Timeouts When the keypad is left idle, it automatically:  
• turns the “Backlight Off After” the selected backlight off time has expired (unless “Never” option is selected).   
• returns to the “Home” screen after the selected “To Homepage After” time has expired (unless “Never” option is selected), and 
• if enabled, the “Auto Slideshow After” time begins the slide show.  
To select the desired screen timeouts, do the following: 
ICON ACTION  NOTES 
  1. From the...