Honeywell series TouchCenter Keypads 6271 User Manual

Advanced System Features (Contd) 
41 
How to Enter Console Emulation Mode 
To access the TouchCenter Keypad, do the following: 
1.  From the Hom e screen, press the SECURITY button.  The Arming screen  
is displayed.
 
SCREEN ACTION 
2.  Press the MORE CHOICES button.  
The More Choices screen is displayed. 
3.  Press the CONSOLE MODE button on 
the More Choices screen.  The Keypad 
screen is displayed. 
4.  Perform functions as you would from a 
regular alpha keypad.  

 
42 
Voice Messages (6271V/6271CV Only)  
Introduction to Recording and Retrieving Messages 
The 6271V and the 6271CV provide the capability of recording voice 
messages for others on the premises. The number of messages is not 
limited; however, the total time of all messages added together cannot 
exceed 262 seconds. 
Note: The voice messages are stored in the memory of the 6271V and 
6271CV. All messages will be lost if the 6271V and 6271CV loses 
power or if it is reset. 
Voice messages are recorded...

Voice Messages (Contd) 
43 
Recording a Voice Message 
To record a voice message, do the following: 
1. From the Home screen, press the Message button.  The Message 
Center screen is displayed. 
2. Press the Record button and record your message while staying 
within approximately one foot of the TouchCenter and speaking at a 
normal voice volume.  As you are recording your message, the 
remaining time counter counts down to indicate the total remaining 
time available and a “Recording New Memo…” message...

Voice Messages (Contd) 
44 
Retrieving and Deleting a Voice Message 
To retrieve a voice message, do the following: 
1.  From the Home screen, press the MESSAGE button.  The Message 
Center screen is displayed. 
SCREEN ACTION 
2.  Select the message you wish to listen 
to by touching it in the message list and 
then pressing the Play Message button.  
As the message is being played, a “Play 
(x): Voice Memo…” message is displayed 
above the message list window. 
When the end of the message is reached,...

 
45 
Summary of LED Operation 
LED Operation 
The TouchCenter has three LEDs labeled - ARMED, READY and 
TROUBLE (6271C, 6271CS and 6271CB) or MESSAGE (6271V and 
6271CV). The ARMED LED is red, READY LED is green and 
TROUBLE or MESSAGE LED is yellow. Each LEDs on and off state 
has different meanings as described below.  
LED DESCRIPTION 
ARMED  ON – Security system is arm ed. 
OFF – Security system is not armed. 
READY  ON – Security system is disarmed and ready to arm. 
OFF – Security system is armed...

 
46 
TouchCenter Setup  
How to Access TouchCenter Setup Options 
Setup allows you to make changes to the way your TouchCenter is 
operating. The options that can be changed are: 
•  Adjust the touch screen contrast  
•  Adjust the TouchCenter sounder volume 
•  Change the time interval that must pass prior to the TouchCenter 
turning off the touch screen backlight 
•  Change the time interval that must pass prior to the TouchCenter 
returning to the “Home” screen 
Additionally, you may enter the User...

TouchCenter Setup (Contd) 
47 
How to Adjust the Contrast 
To increase the contrast, move the slide bar above the current 
contrast setting. 
To decrease the contrast, move the slide bar below the current 
contrast setting. 
If you have made any changes in the contrast settings, when you exit 
this screen you will be presented with a pop-up asking if you want to 
remember the new settings. 
CONTRAST
SLIDE BAR
INDICATOR
VOLUME
SLIDE BAR
INDICATOR
 
 
Touch Screen Contrast and Volume Controls 
How to...

TouchCenter Setup (Contd) 
48 
How to Select Screen Backlight Off Activation Time 
When the TouchCenter is not active, it will automatically turn the 
backlight off after the selected backlight off time has expired (unless 
“Never” option is selected).  To select the screen backlight time, do the 
following: 
SCREEN ACTION 
1.  On the Setup screen, press the 
Backlight Off After: arrow button.  A 
drop-down list displaying the time period 
options is displayed. 
2.  Select the time period option you want...

TouchCenter Setup (Contd) 
49 
How to Select Homepage After Time 
When the TouchCenter is not active, it will automatically return to 
the “Home” screen after the selected To Homepage After time has 
expired (unless “Never” option is selected).  To select the To 
Homepage After time, do the following: 
SCREEN ACTION 
1.  On the Setup screen, press the To 
Homepage After arrow button.  A drop-
down list displaying the time period 
options is displayed. 
2.  Select the time period option you want 
by...

TouchCenter Setup (Contd) 
50 
SCREEN ACTION 
3.  Press either the Hom e or Back 
button.  A Settings Changed! pop-up 
window is displayed asking “Remember 
New Settings?“ Select Yes to save the 
change or No to discard the change. 
 
 
 
When the Update is complete the 
TouchCenter goes to the Hom e screen 
or More Choices screen depending on 
whether you pressed the Hom e or 
Back button, respectively.