Honeywell series TouchCenter Keypads 6272 User Manual

							 
Security (Contd) 
31 
SCREEN ACTION  
The first ten events will be displayed. 
To view all item s, press the Show More 
button and press the up/down arrows to 
scroll through the event log.   
Notes:  
•  W hen  All Partitions  or All Events  
button is pressed, and more than 100 
events exist, the Show More  button 
text will change to read  Next>>. If you 
press the  Next>> button, a 
  and  and  
						

							 
Security (Contd)   
32 
How to Send Emergency Messages 
 
•  Emergency messages are optional and may not be available on your 
system. Ask your system installer if emergency messages are 
available on your system. 
•  The  Emergency  screen cannot be accessed while running a screen 
diagnostic test or while in the clean screen mode. 
An emergency message for fire, panic, or medical can be sent to the 
central monitoring station from the Emergency  screen.  The 
Emergency  screen can be accessed by activating the PANIC Icon 
located on the lower right corner of the screen. 
Once the  Emergency  screen is accessed, perform the following to 
send an emergency message. 
SCREEN   ACTION 
On the Emergency screen press and hold 
(for at least 2 seconds) the associated 
alarm button for the type of emergency 
message you want to send (FIRE, PANIC, 
or  MEDICAL ).  You are imm ediately 
returned to the screen from which you 
pressed the “PANIC” Icon.  
						

							 
33 
Voice Messages  
Introduction to Recording and Retrieving Messages 
The 6272 Series devices provide the capability of recording voice 
messages for others on the premises. The number of messages is not 
limited; however, the total time of all messages added together cannot 
exceed 120 seconds. 
Note: The voice messages are stored in the memory of the 6272 and 
a ll messages will be lost  if the 6272 loses power or if it is reset. 
Voice messages are recorded and retrieved using the “Message 
Center” screen. The below illustration identifies the various areas 
and buttons on the “Message Center” screen. 
PLAY
MESSAGE
ADVANCE ONE
MESSAGE
AND PLAY
BACKUP ONE MESSAGEAND PLAY MESSAGE
LIST
WINDOW
6272-002-V0
STOP
VOLUME
DELETE
RECORDING
TIME REMAINING
RECORD
 
Message Center Screen 
Recording a Voice Message 
To record a voice message, do the following: 
1 . From the Home screen, press the Message button.  The Message 
Center screen is displayed. 
2. Press the  Record button and record your message while staying 
within approximately one foot of the TouchCenter and speaking at a 
normal voice volume.  As you are recording your message, the 
remaining time counter counts down to indicate the total remaining 
time available and a “Recording New Memo…” message is displayed 
above the message list window.  
						

							Voice Messages (Contd) 
 
34 
3.  Press the Stop button when you are done recording the message.  
The message indicator will be flashing and the message will be listed 
in the message list window. 
4.  To record additional messages, repeat steps 2 and 3 above or to 
exit, press the  BACK or HOME  button and the “Home” screen will be 
displayed. 
Retrieving and Deleting a Voice Message 
To retrieve a voice message, do the following: 
1.  From the Home screen, press the MESSAGE button.  The Message 
Center screen is displayed. 
SCREEN ACTION 
2.  Select the message you wish to listen 
to by touching it in the message list and 
then pressing the Play Message  button.  
As the message is being played, a “Play 
(x): Voice Memo…” message is displayed 
above the message list window. 
When the end of the message is reached, 
the playback will stop. 
 
3.  To listen to the next message, press 
the Advance One Message and Play  
button. 
Note:  At any time you may highlight a 
message you want to listen to and press 
the Play Message button as described in 
step 2 above. 
4.  If you wish to delete messages, press 
the Delete  button. The “Delete Mem o” 
screen will be displayed. You can press 
the Del Selected  button to delete only the 
currently selected message and return to 
the “Message Center” screen, Del All  
button to delete all messages and return 
to the “Message Center” screen, 
or the  Cancel  button to return to the 
“Message Center” screen without deleting 
any messages. 
5.  To exit, press the  BACK or HOME 
button and the “Home” screen will be 
displayed.  
						

							 
35 
  Setup 
Setup 
Setup allows you to make changes to the way your TouchCenter is 
operating. The options that can be changed are: 
•  Adjust the touch screen brightness  
•   Adjust the TouchCenter sounder volume 
You may access the  Display & Audio Setup , System Setup  (if 
enabled by your system installer), and  Slideshow Setup  from the 
Setup screen by pressing the corresponding button. 
How to Access Setup 
Access the Setup features as follows: 
1.  From  the Hom e screen, press the Setup  button.  The Setup screen is 
displayed.
 
SCREEN ACTION 
2.  Adjust the TouchCenter options as 
described in the paragraphs that follow. 
  
						

							Setup (Contd) 
36 
 
Adjust the Brightness 
You may adjust the brightness settings by pressing your finger on the 
slide bar associated with the Brightness scale and doing the 
following: 
To increase the brightness, move the slide bar above the current 
brightness setting. 
To decrease the brightness, move the slide bar below the current 
brightness setting. If you have made any changes in the brightness settings, when you 
exit this screen a Settings Changed! pop-up window is displayed 
asking Remember New Settings? Select Yes to save the change or 
No to discard the change. 
            6272-001-V0
BRIGHTNESS SLIDE BAR
INDICATOR
VOLUME
SLIDE BAR
INDICATOR
                 
 
Brightness and Volume Controls 
Adjust the Volume  
You may adjust the sounder volume by pressing your finger on the 
slide bar associated with the Volume scale and doing the following: 
To increase the volume, move the slide bar above the current volume 
setting. 
To decrease the volume, move the slide bar below the current volume 
setting. 
If you have made any changes in the contrast settings, when you exit 
this screen Settings Changed! pop-up window is displayed asking 
Remember New Settings? Select Yes to save the change or No to 
discard the change. 
						

							Setup (Contd) 
37 
Disp & Audio Setup 
Operating Modes  
Operating modes allows you to turn the TouchCenter chime mode on 
or off. Additionally, you may also turn the voice mode on or off. The 
operating modes provide the following features: 
•  Chime Mode – When selected, a request is sent to the alarm panel 
requesting that the panel chime the TouchCenter whenever a 
change in zone status occurs. 
•   Voice Mode – When selected, a request is sent to the alarm panel 
requesting that the panel initiate TouchCenter voice annunciation 
whenever a change in system status occurs such as Armed, 
Disarmed, or Alarms. 
•   Voice Chime – The chime mode and voice mode are in effect with 
the chime followed by voice annunciation. 
 
Access the Display and Audio Setup screen as follows: 
1. From the Home screen, press the  Setup button. 
SCREEN ACTION 
1. The Setup screen is displayed. 
2.  Press the Disp&Audio Setup  button.   
If enabled, the User Authorization 
screen is displayed with the instructions 
 Enter Authorized Code  
3.  Enter your “Authorized Code.  The 
Display and Audio Setup screen is 
displayed. 
4.  Touch the Chime Mode button to turn 
the Chime Mode on or off. A checkmark 
appears in the button when the Chime 
Mode is  “ON ”. Note that it may take a few 
seconds for the Chime Mode to take 
effect. 
 
  
						

							Setup (contd) 
38 
SCREEN ACTION 
5. Touch the Voice Mode button to turn 
the Voice Mode on or off. A checkm ark 
appears in the button when the Voice 
Mode is “ON ”.  Note that if the Chime 
Mode and Voice Mode are both selected, 
the Voice Chime button will automatically 
be selected. 
Press the  “HOME ” or “ BACK ” button after 
making your selection. W hen the 
TouchCenter exits the  “Operating Modes ” 
screen, your selection is saved. 
Language Selection 
The TouchCenter allows you to select from six different languages, 
(English, French Canadian, Italian, Portuguese, South American 
Spanish and European Spanish) with the default being English.  
Set the Language Selection feature as follows: 
1.  From  the Hom e screen, press the Setup  button.  The Setup screen is 
displayed.  
SCREEN ACTION 
2.  Press the Disp&Audio Setup  button.  
The Display and Audio Setup screen is 
displayed. 
If enabled, the User Authorization 
screen is displayed with the instructions 
 Enter Authorized Code .  
4.  Enter your “Authorized Code.  The 
Display and Audio Setup screen is 
displayed. 
  
						

							Setup (Contd) 
39 
SCREEN ACTION 
5. To select a specified language, choose 
English, French Canadian, Portuguese, 
South American Spanish, European 
Spanish and Italian). Once the language 
is selected, the keypad will revert back to 
Home screen with the selected language 
applied. 
 
 
Backlight Off Activation Time 
When the TouchCenter is left idle, it will automatically turn the 
backlight off after the selected backlight off time has expired (unless 
“Never” option is selected).  To select the screen backlight time, do the 
following: 
SCREEN ACTION 
 1.  On the 
Display and Audio Setup 
screen, press the  Backlight Off After: 
arrow button.  A drop-down list 
displaying the time period options is 
displayed. 
 
 
 
2.  Select the time period option you want 
by pressing it.  The drop-down list closes 
automatically and the selection is 
displayed. 
Note:   Additional time intervals can be 
viewed by using the up/down arrows to 
select the time period options. 
 
3.  Press either the Hom e, Back, 
Home Setup or RESET Home Setup 
buttons.  A   Settings Changed!  pop-up 
window is displayed asking  “Remember 
New Settings? “ Select Yes  to save the 
change or  No to discard the change.  
						

							Setup (contd) 
40 
SCREEN ACTION 
When the update is complete, depending 
on which selection you made, ( Home, 
Back, Home Setup or RESET Home 
Setup) the TouchCenter will go to its  
respective selected screen.  
Homepage After Time 
When the TouchCenter is left idle, it will automatically return to the 
“Home” screen after the selected To Homepage After time has expired 
(unless “Never” option is selected).   
 
  This option is only available if the EN50131 display option is not enabled by the installer. 
To select the To Homepage After Time, do the following: 
SCREEN ACTION 
1.  On the Display and Audio Setup 
screen, press the  To Homepage After 
arrow button.  A drop-down list 
displaying the time period options is 
displayed.