Honeywell series TouchCenter Keypads 6272 User Manual

							 
 Setup (Contd) 
51 
SCREEN  ACTION 
 
10.  Press the Save button.  The system 
will save the configuration.  W hen the 
save is complete, the User Setup screen 
is displayed with the new user ’s name 
shown. 
 
 
 
 
How to Delete a User 
Delete a User as follows: 
SCREEN ACTION 
Three selections are available: add a 
user, edit a user, or delete a user. 
1.  To delete a user, touch the circle next 
to the user to be deleted and press the 
DELETE USER  button.  The User 
Authorization screen is displayed with the 
instructions  Enter Authorized Code .  
2.  Enter your Authorized code.  The 
Confirm Delete screen is displayed. 
Note:  The authorized code for deleting, 
adding, and editing users is dependent 
upon the alarm panel you are interfacing 
with. Check your alarm panel Installation 
and Setup Guide to determine who can 
delete, add, and edit users.  
						

							 
Setup (Contd) 
52 
SCREEN ACTION 
3.  Press the appropriate button.  The 
User Setup screen is displayed. 
 
How to Edit a User 
Note: You cannot edit a User’s name or User number. To modify a 
User name or User number, you must delete the User and re-enter 
User. 
Edit a user as follows: 
SCREEN   ACTION 
Three selections are available: add a 
user, edit a user, or delete a user. 
1.  To edit a user, touch the circle next to 
the user to be edited and press the EDIT 
USER button.  The User Authorization 
screen is displayed with the instructions 
 Enter Authorized Code .  
2.  Enter your Authorized code.  The  “User 
Options ” screen is displayed. 
Note:  The authorized code for editing 
users is dependent upon the system you 
have. Check with your system installer to 
determine who can edit users.  
						

							 
 Setup (Contd) 
53 
SCREEN  ACTION 
3.  Select the options needed for this user 
and press the SAVE button.  The 
configuration changes are saved and you 
are returned to the User Setup  screen. 
Safe Mode 
In the rare event that the TouchCenter cannot successfully 
communicate in its graphic mode with the control panel, the Safe 
Mode is a backup mode that ensures that you can communicate with 
your system.  
In this mode, the TouchCenter operates much like a standard non-
graphic keypad so that you can control your system until the problem 
is corrected. 
If this situation occurs, the TouchCenter presents you with a message 
of “Problems detected. Start Keypad in Safe Mode?” and requests a 
“Yes” or “No” response. If you answer with “Yes”, the TouchCenter 
will go into the Safe Mode. If you answer with “No”, the TouchCenter 
will try communicating with the panel again. After 3 consecutive 
times of receiving no response, the TouchCenter will enter the Safe 
Mode automatically. 
Note: Use care when providing the “Yes” or “No” response. Touching 
the screen outside the prescribed area may cause the background to 
come to the front. If this occurs, the Yes/No message that disappeared 
will time out in 30 seconds even though it is not visible. Then the 
keypad will reset into the Normal Mode (or Safe Mode if this is the 
third time that the warning message appeared). 
While in the Safe Mode, the Home screen will display the Security 
Button, Panic Button, Message Button, and a message at the bottom 
of the screen as shown below: 
  
						

							 
Setup (Contd) 
54 
Note that this is a limited mode of operation. While in this mode: 
•  You can use the Security button to access the Console Emulation 
Mode of operation to try to clear your faults, disarm the system, or 
enter additional Alpha Keypad commands specified in your panel 
User Guide. You can perform almost all functions that you can 
perform from a standard non-graphic alpha keypad. 
•   You can press the “Panic” key and generate Emergency Messages 
as defined in the panels home partition for this TouchCenter. 
•   The Armed and Ready LEDs on the front of the TouchCenter will 
indicate the TouchCenter’s home partition status. The Message (
on 
models with Voice feature
) or Trouble (on models without Voice 
feature) LED is not active in the Safe Mode. 
•   The Chime mode will function in the Safe Mode. 
•   When an alarm occurs in the Safe Mode, it is displayed on the 
Console mode screen only and will not be shown on the Home 
screen  
To Exit the Safe Mode: 
1. Press the ! SAFE MODE ! bar. You will be presented with the  following popup message: 
 
2. Select “Yes” to return to the Normal Mode of operation. The 
TouchCenter will reset and normal operation will return as long as 
the original conditions that caused the entry into Safe Mode do not 
still exist. 
Time/Date Setup 
You can set the time and date from the  Set Time & Date screen.  
•   When the time is set it will be stored in the TouchCenter and sent 
to the control panel when you press the  Apply button and answer  
						

							 
 Setup (Contd) 
55 
Yes to the following prompt. Additionally, when using the 
TouchCenter with a residential panel, the panel will download its 
time into the TouchCenter once an hour after the clock is set. 
•   If Get Time  is pressed, the TouchCenter will download the time 
and date from the control panel and exit the Set Time & Date 
screen.  Note: This button appears with residential panels only. 
•   If DST On  (Daylight Savings Time) is selected, the TouchCenter 
will adjust for Daylight Savings time at the month, week and 
time chosen. 
Setting Daylight Savings Time 
From the Home screen press the  Setup button. Press the System 
Setup button and do the following: 
SCREEN ACTION 
1.  From the System Setup screen,  press the  Time/Date Setup  button. If 
enabled, the User Authorization 
screen is displayed with the 
instructions  Enter Authorized 
Code . 
 
 
2. Enter your Authorized Code. 
  
						

							 
Setup (Contd) 
56 
SCREEN ACTION 
3.  Select if you want Daylight Savings 
Time to affect your system clock by 
touching the DST button.  
The DST screen is displayed. 
4.  On the Daylight Savings screen, 
press the  M onth arrow button in the 
“ Start DST ” area of the screen.  A drop-
down list displaying the Months is 
displayed. 
5.  Select the month you want by pressing 
it.  The drop-down list closes automatically 
and the selection is displayed. 
 
6.  On the Daylight Savings screen, 
press the  Weekend  arrow button in the 
“ Start DST ” area of the screen.  A drop-
down list displaying the weeks is 
displayed. 
7.  Select the week you want by pressing 
it.  The drop-down list closes automatically 
and the selection is displayed. 
 
8.  On the Daylight Savings screen, 
press the  M onth arrow button in the 
“ End DST ” area of the screen.  A drop-
down list displaying the Months is 
displayed. 
9.  Select the month you want by pressing 
it.  The drop-down list closes automatically 
and the selection is displayed. 
  
						

							 
 Setup (Contd) 
57 
SCREEN ACTION 
10.  On the Daylight Savings screen, 
press the Weekend  arrow button in the 
“ End DST ” area of the screen.  A drop-
down list displaying the weeks is 
displayed. 
11.  Select the week you want by pressing 
it.  The drop-down list closes automatically 
and the selection is displayed. 
 
12.  On the Daylight Savings screen, 
press the arrow button to the right of the 
time (1 AM or 2 AM) on the screen.  A 
drop-down list displaying 1 AM and 2AM 
is displayed. 
Make sure DST On is checked to enable 
this feature. 
13.  Select the tim e you want by pressing 
it.  The drop-down list closes automatically 
and the selection is displayed. 
14. Press the APPLY button to save your 
Daylight Savings Time setup. The  “Time 
and Date screen is displayed. 
 
Setting Current Time and Date 
To set the current time, do the following: 
SCREEN ACTION 
1.  On the Time and Date screen, press 
the  M onth  arrow button.  A drop-down 
list displaying the months is displayed. 
2.  Select the current month by pressing it.  
The drop-down list closes automatically 
and the selection is displayed. 
  
						

							 
Setup (Contd) 
58 
SCREEN ACTION 
3.  On the Time and Date screen, press 
the Year that is being displayed.  A Year 
screen is displayed with the instructions to 
Enter 4 digits for the year . 
4.  Enter the four digits for the current 
year. 
The window closes automatically and the 
selection is displayed. 
5. On the Tim e and Date screen, press 
the Hour that is being displayed.  An hour 
screen is displayed with the instructions to 
Enter 2 digits for the hour . 
6. Enter the two digits for the current hour. 
The window closes automatically and the 
selection is displayed.  
						

							 
 Setup (Contd) 
59 
SCREEN ACTION 
7. On the Tim e and Date screen, press 
the Minutes that is being displayed.  A 
minute screen is displayed with the 
instructions to Enter 2 digits for the 
minutes . 
8. Enter the two digits for the current 
minute. 
The window closes automatically and the 
selection is displayed. 
9.  Select if it is AM or PM by pressing on 
the AM or PM display on the screen. Each 
depression switches the AM/PM display. 
10. Select the day of the month by 
touching the proper day in the display. 
The selected date will be highlighted on 
the screen. 
11. On the Time and Date screen, press 
the  M onth/Day/Year  arrow button.   A 
drop-down list displaying the 
Month/Day/Year display formats is 
displayed. 
12.  Select the display format you want by 
pressing it.  The drop-down list closes 
automatically and the selection is 
displayed. 
13.  Select if you want a 12-hour or 24-
hour format for your time display by 
touching the circle to the left of the  12 
Hour  display.  A check mark in the circle 
indicates a 12-hour display format.  
						

							 
Setup (Contd) 
60 
SCREEN ACTION 
14. On the Time and Date screen, press 
the Apply button.  A confirmation screen 
is displayed. 
15. Press the Yes  button to save the time 
changes in your security system or press 
the No  button to have the changes affect 
the TouchCenter only. 
Note:  A Yes  response is recommended.