HP CM8060 User Manual

2 Connect the device
This chapter contains information about the following topics:
●
Interface ports
●
Connect to a phone line
●
Connect to a network
ENWW 17
 

Interface ports
The following figure shows the interface ports for the device.
1Boot Codes LCD monitor (for service use only)
2Host USB (for connecting an accessory to the device)
3Fax (RJ-11) (covered with label)
4Embedded LAN (RJ-45) (no telecommunication connections)
5CAN Interface (Finisher)
6Engine Interface (PCI Express)
7Scanner Interface
8EIO Slot
9FIH (Foreign Interface Harness)
10Device USB (for connecting the device to a computer)
11Status LEDs for (service use only)
12 Engine Power Control...

Connect to a phone line
The device must be connected to an analog phone line to send and receive faxes. Connect the device
to a phone line by doing the following:
1. Remove the label that covers the Fax (RJ11) interface port.
2.Plug one end of a phone cable into the Fax (RJ11) interface port.
WARNING! For protection against overvoltage, use a minumum 26 AWG cable to connect to the
device modem module.
ENWW Connect to a phone line 19
 

3.Plug the other end of the phone  cable into your phone service.
20 Chapter 2   Connect the device ENWW
 

Connect to a network
HP recommends that you use the HP software installer CD that comes with the device to set up the
device using the network configurations. You are not required to install additional software if you use
the installer. There are two possible netw ork device and printing configurations:
● The device is connected directly to the network (d
irect mode or peer-to-peer printing). Each network
user prints directly to the network address or ho stname of the device. This network configuration...

4.Select the language that you would like the installer to use, and accept the license agreement to
continue.
5. On the  Printer Connection  screen, select Wired Networking .
6. On the  Printers Found  screen, select whic h device to install.
7. On the  Confirm Settings  screen, verify the device settings.
NOTE:To manually change the network address of the device, click  Change Settings on the
Confirm Settings  screen and follow the prompts.
8.On the  Installation Type  screen, select the type of...

3 Device software
●Supported operating systems and printer drivers
●
Install the software
●
Uninstall the software
●
Installer Customizatio n Wizard for Windows
Three CDs are included with the device:
● Windows
. Contains the printer driver insta ller for Windows operating systems, user
documentation, the  Installer Customization Wizard , and a link to the HP Universal Printer Driver
on the Web.
● Macintosh
. Contains the printer driver installe r for Macintosh operating systems and user
documentation....

Supported operating systems and printer drivers
The device comes with printer drivers that the computer uses to communicate with the device. Printer
drivers provide access to device fe atures, such as printing on custom-sized paper, resizing documents,
and inserting watermarks.
The printer drivers include online Help that has  instructions for common printing tasks and describes
the buttons, checkboxes, and drop-down  lists that are in the printer driver.
The device uses the PCL 5c, PCL 6, and HP...

●Drivers for SAP printing. For 
more information, go to www.hp.com/go/sap/drivers.
● HP Output management Solutions.
 For more information, go to 
www.hp.com/go/
outputmanagement.
ENWW Supported operating syst ems and printer drivers 25
 

Install the software
Use the printing-system software CD to install the printer drivers and supported software applications.
Each installation type presents a series of dialog  boxes that guide you through the installation process
and ask you to provide information about your computer environment. The installer guides you through
a direct-connect or a networked installation.
Windows
You can choose from the following type s of printer driver installations:
● Typical
. Installs the PCL 6 driver and...