HP Envy 6 Service Manual

							7.Remove the 4 Phillips PM 2x2 display panel screws.
8.Remove any tabs or tape adhering to the display panel (1), and then move the panel towards the
keyboard (2).
NOTE:Support the display panel as you lean the panel forward.
Component replacement procedures 33 
						

							9.Release the support strip (1) covering the display panel connector. Disconnect the display panel
cable from the display panel (2), and then remove the panel (3).
Reverse this procedure to install the display panel.
Base enclosure
Description Spare part number
Base enclosure (Red) 686096–001
Base enclosure (Black) 690197–001
Base enclosure (Red) 689855–001
Before disassembling the computer, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the display panel (see 
Display panel on page 32).
34 Chapter 4   Removal and replacement procedures 
						

							Remove the base enclosure:
1.Turn the computer face down, remove the 12 Phillips PM 7.5 millimeter long screws.
2.Remove the bottom enclosure.
NOTE:To remove the bottom enclosure, use a thin, non-conductive tool such as the HP Tool
Shroud separator, available on the HP website.
Component replacement procedures 35 
						

							Battery
DescriptionSpare part number
4-cell, 60WHr 4.1AH Li-ion battery 681951-001
Before removing the battery, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the display panel (see 
Display panel on page 32).
5.Remove the base enclosure (see 
Base enclosure on page 34).
Remove the battery:
1.Turn the computer right-side up, with the front toward you.
2.Disconnect the battery cable.
3.Move the battery cable to the side (1), and then remove the 6 Phillips PM 2.5×4.2 screws (2) that
secure the battery to the computer.
36 Chapter 4   Removal and replacement procedures 
						

							4.Remove the battery from the computer (3).
Reverse this procedure to install the battery.
Component replacement procedures 37 
						

							Hard drive
DescriptionSpare part number
320-GB 7200RPM SATA 7mm 634862–005
320-GB 5400RPM SATA 7mm 645193–005
500-GB 5400RPM SATA 7mm 683802–005
32-GB mSATA solid-state drive (SSD) 687100–001
128-GB mSATA solid-state drive (SSD) 687101–001
Before removing the hard drive or SSD, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the display panel (see 
Display panel on page 32).
5.Remove the base enclosure (see 
Base enclosure on page 34).
6.Disconnect the battery cable (see 
Battery on page 36).
Remove the hard drive:
1.Disconnect the hard drive cable from the system board (1), and then remove the 4 screws (2)
securing the hard drive to the top cover.
38 Chapter 4   Removal and replacement procedures 
						

							2.Remove the hard drive (3).
3.Remove the hard drive connector cable (1). Remove the 4 screws (2) securing the hard drive
bracket to the hard drive, and then remove the hard drive bracket (3).
4.Remove the hard drive (3).
Remove the mSATA solid-state drive:
Component replacement procedures 39 
						

							▲Remove the screw (1), and then remove the mSATA solid-state drive (2).
Reverse these procedures to reassemble and install the hard drive.
40 Chapter 4   Removal and replacement procedures 
						

							RTC battery
DescriptionSpare part number
RTC battery686922–001
Before removing the RTC battery, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the display panel (see 
Display panel on page 32).
5.Remove the base enclosure (see 
Base enclosure on page 34).
6.Disconnect the battery cable (see 
Battery on page 36).
Remove the RTC battery:
1.Use a thin, non-conductive tool to remove the RTC battery from the socket on the system board.
NOTE:Use a thin, non-conductive tool to remove the RTC battery from the socket on the
system board.
2.Hold down the media card reader board (2), and remove the RTC battery (3). (The RTC battery
is also attached to the system board by foam material rather than double-sided adhesive.)
Component replacement procedures 41 
						

							Reverse this procedure to install the RTC battery on computer models. When installing the RTC
battery, make sure the “+” sign faces up.
42 Chapter 4   Removal and replacement procedures