HP Proliant Ml350 Generation 5 Server User Guide

 
Hardware options installation 41  7. 
(Optional) When shipping a server with a full-height device installed, replace the front guide screw 
with a shipping screw (Installing the full-height media device shipping screw on page 41).  
8. Connect the data and power cables to the rear of the device. 
 
9. Install the access panel (on page 19). 
10. Do one of the following: 
• Close or install the tower bezel, as needed. 
• Slide the server back into the rack.  
Installing the full-height media device...

 
Hardware options installation 42  3. 
Install the silver shipping screw into the full-height device. 
  
Installing a diskette drive 
1. Power down the server (on page 16).  
2. Do one of the following: 
• Open or remove the tower bezel, as needed (Open or remove the tower bezel on page 17). 
• Extend the server from the rack (on page 16). 
3. Remove the media bay blank (Accessing the removable media cage on page 38). 
4. Remove the access panel (on page 18). 
5. Use a T-15 Torx screwdriver to remove...

 
Hardware options installation 43  7. 
Slide the diskette drive into the diskette drive bay. 
 
8. Connect the data and power cables to the rear of the device. 
9. Connect the diskette drive cable to the diskette drive cable connector on the system board (System 
board components on page 10). 
10. Install the access panel (on page 19). 
11. Do one of the following: 
• Close or install the tower bezel, as needed. 
• Slide the server back into the rack. 
12. Power up the server (on page 16).  
Redundant...

 
Hardware options installation 44  2. 
Remove the power supply blank. 
 
  WARNING:  To reduce the risk of electric shock or damage to the equipment, do not 
connect AC power cords to uninstalled power supplies. 
3. Slide the power supply into the power supply bay until the release/lock lever clicks, securing the 
power supply. 
 
4. Using the retaining clip shipped with the server, secure the power cord to the power supply handle. 
Securing the cord will ensure enough slack.  
5. Connect the power cord...

 
Hardware options installation 45 
Removing the expansion slot cover 
To install the component: 
1. Power down the server (on page 16). 
2. Do one of the following: 
• Open or remove the tower bezel, as needed (Open or remove the tower bezel on page 17). 
• Extend the server from the rack (on page 16). 
3. Remove the access panel (on page 18). 
4. Push the release latches on the expansion board retainer and pull the retainer out away from the 
chassis. 
 
5. Remove the expansion slot cover....

 
Hardware options installation 46 
Installing an expansion board 
  CAUTION:  To prevent damage to the server or expansion boards, power down the server and remove all 
AC power cords before removing or installing the expansion boards. 
1. Power down the server (on page 16). 
2. Do one of the following: 
• Open or remove the tower bezel, as needed (Open or remove the tower bezel on page 17). 
• Extend the server from the rack (on page 16). 
3. Remove the access panel (on page 18). 
4. Remove the...

 
Hardware options installation 47 
PCI-X video cards must be installed in slots 2 or 3 only. 
 
7. Close the expansion slot latch to secure the board. 
8. Connect any required internal cables to the expansion board. Refer to the documentation that ships 
with the expansion board. 
9. Install the expansion board retainer.  
10. Install the access panel (on page 19). 
11. Do one of the following: 
• Close or install the tower bezel, as needed. 
• Slide the server back into the rack. 
12. Connect any...

 
Hardware options installation 48  6. 
Connect the parallel and serial cables to the parallel and serial connectors on the system board. 
 
7. Install the access panel (on page 19). 
8. Do one of the following: 
• Close or install the tower bezel, as needed. 
• Slide the server back into the rack. 
9. Power up the server (on page 16). 
10. Enable the feature under the System Options menu in RBSU. For more information on RBSU, refer to 
the HP ROM-Based Setup Utility User Guide on the Documentation CD or...

 
Hardware options installation 49  4. 
Remove the air baffle. 
 
5. Install the redundant fan assembly, making sure the fans click into place.  

 
Hardware options installation 50 
  NOTE:  The fan configuration is redundant only when both fans are installed.  
 
 
6. Connect the redundant fan cables to the redundant fan connectors on the system board (System 
board components on page 10). 
7. Install the air baffle. 
8. Install the access panel (on page 19). 
9. Do one of the following: 
• Close or install the tower bezel, as needed. 
• Slide the server back into the rack. 
10. Power up the server (on page 16).  
Battery-backed write cache...