HP Storageworks Boot From San Manual

							2.SelectBootable DVDfromtheEFIBootManagermenu.
Figure 19 Installing the operating system using the Windows CD-ROM
.3.WhentheHPrecoveryconsolemenuopens,clickRe-install.Ignorethewarningaboutdeleting
alldataonthedriveandclickOK.
4.Whenaskedtoselectthebootdrivepartitionsize,selectCtousethefulldrivesize.
5.UsethelatestSmartSetupCD-ROMtoupdatethesystemdriversandagents.
Itisnotnecessarytore-installtheHBAdriverunlessanupdateisavailable.
NOTE:
For single-path configurations, skip step 6, step 9, and step 10.
6.Installmultipathingsoftwareifapplicable.
7.Installthelatestoperatingsystemservicepack.
8.Reboottheservertocompletetheinstallation.
9.FollowthroughoneachadditionalcontrollerportassignmentfortheHBAs.
10.ConnectanynonbootingHBAs.
11.CreateandassignallotherstorageLUNstotheappropriateHBAs.
Installing from the Microsoft CD-ROM
UsethefollowingprocedurestoinstalltheoperatingsystemusingtheMicrosoftCD-ROM.
Loading the HBA driver for a Windows Server 2003 install
ToloadtheHBAdriver:
1.InserttheHPSmartSetupCD-ROM.
2.SelectBootable DVDfromtheEBSUmenuandpressEnter.
3.SelectLoad OEM Boot driverorpressBtodisplaytheLoadOEMBootDriverscreen.
4.SelecttheappropriateFibreChannelHBAandpressEnter.
5.PressTabonceandthenpressEnter toloadthedriver.
Thesystemdisplaysamessageconfirmingthatthedriverisloaded.
6.SelectExitorpressXtoexit.
Loading the HBA driver for a Windows Server 2008 install
1.Gotowww.hp.comanddownloadtheIA64 Boot from San (Boot from SAN) driver kit.
FibreChannelhostbusadapterssoftwareguideforWindows31 
						

							2.ExtracttheIA64 Boot from SAN kittoaUSBflashdrive.
3.InserttheUSBflashdriveintoanavailableUSBslotonthesystem.
Preparing the SAN disk device for operating system installation
Topreparethediskdeviceforoperatingsysteminstallation:
1.SelectEFI ShellontheEBSUmenu.
2.WiththeHP Smart Setup CD-ROMintheDVDdrive,changetotheCD-ROMfilesystem.
NOTE:
The CD-ROM file system might be mounted somewhere other than fs0.
3.Atthecommandprompt,changetothelocationoftheDiskpartUtility:
Shell>fs1:
fs1:\>cdefi\efi_utils
4.RuntheDiskPartUtility:
fs1:\efi\efi_utils>diskpart.efi
5.Listthepartitionsavailable:
DiskPart>list
Outputsimilartothefollowingappears:
###BlkSizeBlkCount
--------------------------
0200B40
12004800000
NOTE:
Device 0 is the virtual floppy disk and Device 1 is the LUN created to install the operating
system. The BlkCount value varies depending on the size of the LUN created; it does not
match the LUN size.
6.Entertheselectcommandtoselectthebootdevice:
DiskPart>Select1
SelectedDisk=1s
7.Inspectthedisk.Ifamessageotherthanthefollowingdisplays,usethecleancommandto
destroyallpartitionsonthedisk.
DiskPart>inspect
SelectedDisk=1
ThediskisRAW,nothingtoinspect.
BootfromSAN32 
						

							8.ExitDiskPart:
DiskPart>exit
9.RemovetheHPSmartSetupCD-ROMandinserttheWindowsServer2003CD-ROMinthedrive.
10.Rescanthedrives,whichgivestheCD-ROMsystemaccesstotheWindowsCD-ROMfiles.
fs1:\efi\efi_utils>map–r
11.SelectExittoreturntotheEFIBootManagermenu.
Youarenowreadytoinstalltheoperatingsystem.
Installing the Windows Server 2003 operating system
NOTE:
For RX8620 or RX7620 systems, follow the instructions in “Special procedures for RX8620 or RX7620
systems” on page 34 before installing the operating system.
ToinstalltheWindowsServer2003operatingsystem:
1.WiththeWindowsServer2003CD-ROMintheDVDdrive,select Bootable DVD.Pressanykey
toboottheCD-ROMandstarttheinstallationprocess.
NOTE:
Do not press F6 to load any mass-storage device drivers.
2.UsethelatestHPSmartSetupCD-ROMtoupdatethesystemdriversandagents.
3.Tore-installtheHBAdriver,runtheSmartComponentbyselectingDrivers > Driver for FC HBA.
ThissetstheHP-supportedregistryparameters.
4.Installmultipathingsoftware.
5.Reboottheservertocompletetheinstallation.
NOTE:
For single-path configurations, skip steps 6 through 8.
6.ConnectanynonbootingHBAs.
7.Followtheprocedurein.
8.CreateandassignallotherstorageLUNstotheappropriateHBAs.
Installing the Windows Server 2008 operating system
ToinstalltheWindowsServer2008operatingsystem:
1.WiththeWindows Server 2008 CD-ROMintheDVDdrive,selectBootable DVD.Pressanykey
toboottheCD-ROMandstarttheinstallationprocess.
2.Enteryourlanguageandotherpreferences.ClickNexttocontinuetheinstallation.
FibreChannelhostbusadapterssoftwareguideforWindows33 
						

							3.ClickInstall Nowatthenextscreen.
4.EntertheProductLicensekeyandclickNexttocontinue.
5.ReadthetermsoftheLicenseAgreementandchecktheIaccepttheLicenseterms.andclickNext
tocontinue.
6.ClickCustom (Advanced)toinstallacleancopyofWindows,asthereisnoupgradeforWindows
Server2003.
7.ClickLoad DrivertoloadtheIA64BootfromSANdriverkitthatyousavedtotheUSBflashdrive.
8.BrowsetothelocationontheUSBflashdrivethatcontainstheIA64BootfromSANdriverkit.
9.SelecttheappropriateinffileandselectNexttocontinue.
10.SelectthediskwhereyouwanttoinstalltheoperatingsystemandclickNext.
11.Continuewiththeinstallation.
Special procedures for RX8620 or RX7620 systems
UsethefollowinginstallationproceduresforRX8620orRX7620systemsbeforeinstallingtheWindows
operatingsystem.
Running Express Setup
1.WiththeHPSmartSetupCD-ROMintheDVDdrive,selectBootable DVD.
2.SelectExpress Setupandfollowtheon-screeninstructions.
3.AfterWindowsformatsthedriveandreboots,continuewiththeprocedureforaddingtheNOVESA
settingstothebootLUN.
Adding the NOVESA settings
1.SelecttheEFIshellandchangethedirectorytothebootLUN(fs1:).
NOTE:
The boot disk might be mounted in a location other than fs1.
2.ChangethedirectorytoMSUTIL,andthenentertheNVRBOOTcommand.Thefollowingexample
showstheresults:
Shell:\>fs1:
fs1:\>dirDirectoryof:fs1:\07/17/0311:48a127fail_file.txt03/
25/0305:00a841,216SETUPLDR.EFI06/25/0311:14a1,024EFI06/
25/0311:14a1,024MSUtil2File(s)841,343bytes2Dir(s)
fs1:\>cdmsutilfs1:\MSUtil>nvrbootNVRBOOT:OSBootOptions
MaintenanceTool[Version5.2.3683]*1.WindowsServer2003,Enterprise
2.EFIShell[Built-in]*=WindowsOSbootoption(D)isplay(M)odify
(C)opyE(x)port(I)mport(E)rase(P)ush(H)elp(Q)uit
3.Select(M)odifytomodifytheOSbootloader.
4.Enterthebootoptiontoyouwanttomodify:
EnterOSbootoptiontomodify:1
5.Enter2tomodifytheoperatingsystemloadoptions.
BootfromSAN34 
						

							6.EntertheOsLoadOptionscommandwiththe/NOVESAoption:
OsLoadOptions=/redirect/NOVESA
7.Exittheoperatingsystemloadoptions.
FibreChannelhostbusadapterssoftwareguideforWindows35 
						

							BootfromSAN36 
						

							2 HP Emulex HBA installation, configuration,
upgrade and uninstallation
ThischapterdescribesInstallation,configuration,upgradeanduninstallationproceduresforHP
supportedEmulexHBAdriversandfailovermanagementsoftwareusingsingleanddualchannelHP
EmulexHBAswithProLiant(x86andx86_64)andIntegrity(IA64)Windowssystems.
IMPORTANT:
For important troubleshooting information, see Chapter 3, Troubleshooting.
Locating and downloading the Windows Smart Component
driver from the website
Tolocateanddownloadthedriverkitfromthewebsitehttp://h18006.www1.hp.com/storage/
networking/index.html
1.Selecthostbusadaptersfromthewebsitehttp://h18006.www1.hp.com/storage/saninfrastruc-
ture/hba.html
2.Selectyourservertype.
3.UsingtheHPmodelnumberasyourguide,selectyourHBA.
4.IntheSupportsection,selecttheHBAs software and driverlink.
5.SelectDownload drivers and software.
6.SelecttheHBA.
7.Selecttheoperatingsystem.
8.SelectanddownloadtheWindowsdriverkittoyourserver.
Installation and configuration
PerformthefollowingstepstoinstallandconfiguretheHBAsandtheircorrespondingcomponentson
Windowssystems.
•Step1–Installationandconfigurationrulesandassumptions
•Step2–Installationandconfigurationprerequisites
•Step3–InstallingtheHPEmulexdriverSmartComponentkit
•Step4–ConfigureHBAdriver
•Step5–InstallingHBAmanagementsoftware
Step 1 – Installation and configuration rules and assumptions
Beforeyoubegintheinstallationofthesoftware,thefollowingrulesandassumptionsmustbemet.
FibreChannelhostbusadapterssoftwareguideforWindows37  
						

							•AllrulesandassumptionsintheAboutthisguidechapter,aswellasthischapter,havebeensat-
isfied.
•Alreadyinstalledsupportedoperatingsystem.
•Toinstallthedriver,youmustbefamiliarwiththeoperatingsystemunderwhichtheHBAisto
operate,andhaveaccesstooperatingsystemdocumentation.
•HaveAdministratoruserprivileges.
Step 2 – Installation and configuration prerequisites
BeforeinstallingtheHBAdrivers:
•ReviewImportantinformationofthisguide.
•RecordHBAreferencenumbers.Seethesection,Recordingreferencenumbers,page8
•Toobtainthelatestsoftwarekit,driver,applicationsandreleasenotes,followtheinstructionsin
LocatinganddownloadingtheLinuxdriverkitfromthewebsite,page37
•Reviewanyrestrictionsormandatoryupdatesthatapplytoyourconfigurationandoperating
system.
•Ensurethatyoursystemmeetstherequirementsdescribedinthereleasenotes.
•ObtainandloadanyQFEthatisrequiredfortheversionofthedriverthatyouareabouttoload.
TheQFErequirementcanbefoundinthedriverreleasenotes.
Step 3 – Installing the HP Emulex driver Smart Component kit
ThefollowingaredefaultinstructionsforinstallinganHPEmulexdriverkit.
NOTE:
HP recommends installing the complete HP Emulex driver kit. The HP Emulex driver kit is contained
in the HP Smart component.
1.Download the Windows Smart Component driver kit from the website
http://h18006.www1.hp.com/storage/networking/index.html to the target server.
2.Execute the Smart Component.
3.Answer all questions pertaining to the driver load.
4.Reboot the server after the Smart Component completes.
5.From the device manager, select the SCSI icon, and then select the HBA(s). Verify the version of
the driver installed.
If no yellow warning markers appear, the driver version is correct. The Emulex HBA driver has
been installed.
Step 4 – Installing the HBA management software
TheHBAnywareSmartComponentkitislocatedintheUtilitysectionofthepage–thesamelocation
astheSmartComponentdriverkit.
1.ExecutetheSmartComponent.
2.Answerallofthequestionstoinstallthedriverload.
ArebootisnotrequiredfortheHBAnywareinstallationtocomplete.
3.TolaunchHBAnyware,selectStart menu > Emulex > HBAnyware.
HPEmulexHBAinstallation,configuration,upgradeanduninstallation38 
						

							Upgrade
ThissectiondescribesupgradeandupdateproceduresforHPEmulexwithProLiant(x86andx86_64)
andIntegrity(IA64)Windowsserversystems.
Upgrade rules and assumptions
Beforeyoubegin,besurethatalloftherulesandassumptionsinChapter1ofthisguidehavebeen
met.
Upgrade prerequisites
BeforeyouperformHBAupdates,youmust:
•Reviewthelatestreleasenotestoensurethatyouareusingthelatestsupportedconfiguration.
•Ensurethatthesystemisrunningoneoftheoperatingsystemversionslistedinreleasenotes.
•SeetheHPserverPCIslotspecificationstodetermineiftheserveriscompatiblewiththeseHBAs.
•ObtaintheHBASmartComponentdriverkit.
Updating the HP Emulex driver kit
HPrecommendsinstallingthecompleteHPEmulexdriverkit.Thekitcontainsthedriverandutilities
neededtodeployHBAsonWindowsservers.
1.DownloadtheappropriateSmartComponentdriverkitfromthewebsitehttp://
h18006.www1.hp.com/storage/networking/index.htmltothetargetsystem'
2.ExecutetheSmartcomponent
3.Answerallquestionstoupdatethedriverkit.
4.ReboottheserveraftertheSmartComponentcompletes.
5.FromtheDeviceManager,selecttheSCSIiconandthenselecttheHBA(s).Verifytheversionof
thedriverthatisinstalled.
Ifnoyellowwarningmarkersappear,thedriverversioniscorrect.TheEmulexHBAdriverhas
beeninstalled.
Upgrading HBA management software
ToupgradeHBAnywareusethefollowingprocedure:
1.DownloadtheappropriateSmartComponentdriverkitfromthewebsitehttp://
h18006.www1.hp.com/storage/networking/index.htmltothetargetsystem'
2.ExecutetheSmartcomponent
3.Answerallquestionstoupdatethedriverkit.
Arebootofyoursystemisnotrequired.
4.TolaunchHBAnyware,selectStart menu > Emulex > HBAnyware.
Uninstalling HBAnyware
TouninstallHBAnyware:
1.Fromyourserver,gototheControlPanel,andselectAdd/Remove software.
FibreChannelhostbusadapterssoftwareguideforWindows39 
						

							2.SelecttheEmulexHBAnywareandclickRemove.
3.Followtheon-screeninstructionstocompletetheuninstallation.
HPEmulexHBAinstallation,configuration,upgradeanduninstallation40