IBM M400 Projector User Manual
Have a look at the manual IBM M400 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 60 IBM manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 2. Setting up the projector This chapter provides information on positioning the projector, connecting a computer source, using the projector with Microsoft Windows, and displaying and adjusting a computer source image. Starting and shutting down the projector Please follow the steps below to start your projector, and to shut off the projector. Attention: Before moving the projector, be sure to power down the projector normally and disconnect the projector from the main power source. 1. Connect the power cord to the projector as shown in Figure 2-1. Connect the other end to a wall outlet. The Power LED turns on. 2. Remove the lens cover. 3. Attach input devices. 4. Turn on the connected devices. 5. Ensure the Power LED is on a steady (not flashing) amber and then press the Power button to turn on the projector. The projector splash screen displays and connected devices are detected. Attention: Do not look directly into the projection lens when the lamp is turned on. The bright light might harm your eyes. 6. Use the appropriate appliance cable to connect to a video device. 7. To turn off the projector, press the Power button. The projector prepares for shut-down and a ″Power off″ message appears, as shown below. The projector turns off automatically within 5 seconds. Note: This operation can be cancelled by pressing a button other than the Power button. Pressing the Power button again will switch off power. Figure 2-1. Connecting the power cable © Copyright IBM Corp. 2004 2-1
Note: Leave the power cable plugged in for at least 2-5 minutes until the projector returns to room temperature before placing the projector inside the soft case. Placing the projector into the case too soon after switching off the power could cause the projector to overheat. Attention: Before moving the projector, be sure to power down the projector normally and disconnect the projector from the main power source. Positioning the projector To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Following are some general guidelines: v Position the projector on a flat surface at a right angle to the screen. The projector must be at least 1.5 m (4.9 ft) from the projection screen. v Position the projector within 2.7 m (9 ft) of your power source and within 1.8 m (6 ft) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within .15 m (6 in.) of a wall or other object. v Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image. Figure 2-2. 2-2 IBM M400 PROJECTOR: User ’s Guide
Table
2-1.
Zoom
lens
operation
range
(m/ft)
Diagonal
screen
size
(m/in.)
Image
Width
(m/ft)
Image
height
(m/ft)
Distance
from
center
of
lens
to
bottom
of
image
(m/ft)
1-
to
1.20/-
to
3.94
0.66/26
0.53/1.74
0.40/1.31
0.07/0.23
21.54
to
1.85/5.05
to
6.07
1.02/40
0.81/2.66
0.61/2
0.11/0.36
32.33
to
2.80/7.64
to
9.19
1.52/60
1.22/4
0.91/2.99
0.16/0.52
43.12
to
3.75/10.24
to
12.30
2.03/80
1.63/5.35
1.22/4
0.21/0.69
53.91
to
4.70/12.83
to
15.42
2.54/100
2.03/6.66
1.52/4.99
0.26/0.85
64.70
to
5.64/15.42
to
18.50
3.05/120
2.44/8
1.83/6
0.31/1.02
75.89
to
7.07/19.32
to
23.20
3.81/150
3.05/10
2.29/7.51
0.39/1.28
87.04
to
8.45/23.10
to
27.72
4.57/180
3.55/12
2.74/8.99
0.47/1.54
97.85
to
9.44/25.79
to
30.97
5.08/200
4.05/13.32
3.05/10
0.52/1.71
Adjusting
the
projector
level
and
height
To
adjust
the
projector
level
and
height,
complete
the
following
procedure:
1.
To
raise
the
height
of
the
projector,
lift
the
projector
and
press
the
height-adjuster
buttons.
The
elevator
foot
drops
down.
2.
To
make
minor
adjustments
to
the
height,
rotate
the
elevator
foot.
3.
To
lower
the
level
of
the
projector,
press
the
height-adjuster
button
and
press
down
on
the
top
of
the
projector.
Chapter
2.
Setting
up
the
projector
2-3
Note: v The projector table or stand should be level and sturdy. v Position the projector so that it is perpendicular to the screen. v Be sure cables are not in a place where they can cause the projector to be knocked over. Adjusting the image To adjust the zoom, focus, and keystone for the image, complete the following steps: 1. Twist the rings on the projector to adjust the zoom and focus, as shown below. 2. Use the Keystone buttons (on the remote only) to correct image-trapezoid (wider top or bottom) effect. The Keystone buttons on the remote are shown below. 2-4 IBM M400 PROJECTOR: User ’s Guide
The
keystone
control
appears
on
the
OSD,
as
shown.
To
adjust
the
keystone
on
the
projector,
press
Quick
Menu
and
select
the
keystone
submenu;
then
use
the
left/right
buttons
to
adjust
the
keystone.
Image
resolution
The
XGA
resolution
of
the
projected
image
is
1024
x
768
(XGA).
The
projector
is
compatible
with
screen
resolutions
up
to
1280
x
1024
(SXGA).
If
your
computer
screen
resolution
is
higher
than
1280
x
1024
(SXGA),
reset
it
to
a
lower
resolution
before
you
connect
the
projector.
Note:
The
image
automatically
expands
640
x
480
(VGA)
and
800
x
600
(SVGA)
images
to
1024
x
768
(XGA).
Adjusting
the
volume
To
adjust
the
volume,
please
follow
the
steps
below:
1.
Press
the
Volume
+/-
buttons
(shown
below)
on
the
projector
or
the
remote
control.
The
volume
control
appears
on
the
OSD.
2.
Use
the
Volume
+/-
buttons
to
adjust
the
level.
The
remote
volume
control
buttons
are
shown
below.
3.
Press
the
Mute
button
(on
the
remote
control
only)
to
turn
off
the
volume.
Press
the
Mute
button
again
to
turn
off
mute.
Shown
below
is
the
OSD
when
Mute
is
activated.
Chapter
2.
Setting
up
the
projector
2-5
Chapter
3.
Connecting
devices
to
the
projector
This
chapter
provides
information
on
connecting
devices
to
the
M400
projector.
Connecting
devices
Computers
and
video
devices
can
be
connected
to
the
projector
at
the
same
time.
Check
the
user ’s
manual
of
the
connecting
device
to
confirm
that
it
has
the
appropriate
output
connector.
1
USB
slot
2
Audio
3
Video
mini-jack
4
DVI-I
©
Copyright
IBM
Corp.
2004
3-1
Chapter
4.
Using
the
projector
features
This
chapter
provides
information
on
using
the
remote
control,
audio,
keypad
buttons,
and
other
projector
features.
Using
the
remote
control
The
remote
uses
two
provided
AAA
batteries.
They
are
easily
installed
by
sliding
the
cover
off
the
back
of
the
remote,
aligning
the
+
and
-
ends
of
the
batteries,
sliding
them
into
place,
and
then
replacing
the
cover.
CAUTION:
To
reduce
the
risk
of
injury
to
the
eyes,
do
not
look
directly
into
the
remote
control
laser
light
and
do
not
point
the
laser
light
into
anyone’s
eyes.
The
remote
control
is
equipped
with
a
Class
II
laser
that
emits
radiation.
The
figure
below
provides
an
illustration
of
the
remote.
1
Laser
1
2
2
IR
transmitter
3
Status
LED
4
Auto
5
Blank
6
Enter
7
Up
cursor
8
Right
cursor
9
Cursor
pad
10
Keystone
top
11
Keystone
bottom
12
Mute
13
Right
mouse
14
Left
mouse
15
Volume
down
16
Volume
up
17
Down
cursor
18
Left
cursor
19
Menu
20
Freeze
21
Source
22
Power
©
Copyright
IBM
Corp.
2004
4-1
Inserting the remote control batteries When using the remote control for the first time, install the batteries that were supplied. Follow the steps below for inserting new batteries into your remote control. 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow, as shown. 2. Insert the supplied batteries taking note of the polarity (+/-), as shown. 3. Replace the cover, as shown. Note: v Only use AAA alkaline batteries. v Dispose of used batteries according to local government ordinance regulations. v Remove the batteries when not using the remote for prolonged periods. 4-2 IBM M400 PROJECTOR: User ’s Guide