IBM Thinkpad T30 Manual

1090 Keyboard
For access, remove these FRUs, in order:
v“1010 Battery pack”on page 61
v“1020 Ultrabay Plus device”on page 62
v“1030 Hard-disk drive”on page 63
v“1050 Backup battery”on page 67
v“1060 DIMM”on page 69
1
Step Screw (quantity) Torque

1M2.5×16 mm, nylon-coated (2) 0.392 Nm
(4 kgfcm)
(continued)
Removing and replacing a FRU
ThinkPad T3077 

2
3
4
In step
5, pull the keyboard a little in the direction of the
arrow, and then detach the connector
6.
5
6
Removing and replacing a FRU
78ThinkPad T30 (MT 2366, 2367) 

When installing:Install the keyboard, following the
directions below.
1. Attach the connector. (Step
6in the removal
procedure.)
2. Make sure that the keyboard edges, shown in the
figure as(A)and(B), are under the frame.
(A)(B)
3. Press the keys indicated by arrows to latch the
keyboard firmly in place.
(continued)
Removing and replacing a FRU
ThinkPad T3079 

4. To make sure that the front side of the keyboard is
housed firmly, gently press the keys with your thumbs
and try to slide the keyboard towards you.
5. Secure the keyboard from the bottom of the computer,
using the new screws provided with the keyboard.
Removing and replacing a FRU
80ThinkPad T30 (MT 2366, 2367) 

1100 Fan assembly
For access, remove these FRUs, in order:
v“1010 Battery pack”on page 61
v“1020 Ultrabay Plus device”on page 62
v“1030 Hard-disk drive”on page 63
v“1050 Backup battery”on page 67
v“1060 DIMM”on page 69
v“1090 Keyboard”on page 77
Remove the keyboard CRU insulator before removing the
fan assembly.
(continued)
Removing and replacing a FRU
ThinkPad T3081 

11
2
4
2
3
Step Screw (quantity) Torque

1M2×16 mm, nylon-coated (3) 0.245 Nm
(2.5 kgfcm)
When installing:Make sure that the connector
4is
firmly attached.
NoteFor the following models, apply thermal grease on
the part indicated by arrow
a.
v2366-all except FBx, JBx, M6x, M7x
v2367-all except FBx
a
Removing and replacing a FRU
82ThinkPad T30 (MT 2366, 2367) 

NoteWhen you replace the system board, I/O card, CPU
or the base cover for the following models, you
need to stick new thermal sheet as shown in the
following procedure.
v2366-FBx, JBx, M6x, M7x
v2367-FBx
1. Peel the cover sheet (square) off
1. Then stick the
thermal sheet to fit to the guide line on the fan
assembly
2.
2
1
2. Rub over the cover sheet with your finger to stick the
thermal sheet to the fan well
3.
3
(continued)
Removing and replacing a FRU
ThinkPad T3083 

3. Peel the cover sheet (rectangle)
3in the direction of

b. Do not pull the cover sheet (rectangle) upword
(
a) to avoid the thermal rubber comes off with the
sheet.
4
ab
If some part or the thermal rubber came off with the
cover sheet, stick the cover sheet on the fan assembly
again aligning the cracked position. Then rub over the
cover sheet with your finger well and remove the sheet
again.
Removing and replacing a FRU
84ThinkPad T30 (MT 2366, 2367) 

111 0 C P U
For access, remove these FRUs, in order:
v“1010 Battery pack”on page 61
v“1020 Ultrabay Plus device”on page 62
v“1030 Hard-disk drive”on page 63
v“1050 Backup battery”on page 67
v“1060 DIMM”on page 69
v“1090 Keyboard”on page 77
v“1100 Fan assembly”on page 81
Note:There are two types of CPU socket. Confirm the
socket type of the computer first.
Rotate the head of the screw (A) in the direction of the
arrow
1to release the lock; then remove the CPU.
1A
1
A
Removing and replacing a FRU
ThinkPad...

When installing:Place the CPU on the CPU socket (
1),
and then rotate the head of the screw
(A) in the direction of arrow
2to
secure the CPU.
1
2A
2A
1
Removing and replacing a FRU
86ThinkPad T30 (MT 2366, 2367)