Indesit Idca G35 B Manual



	





	
Where to install the tumble dryer
Ventilation
Electrical connections
Preliminary information
	


 
Features
Control panel
!


#$
Starting and selecting a programme
%
#
		&(
Programme chart
Special programmes
Options
Opening the door
)

Sorting laundry
Care labels
Special items
Drying times
*
#		##		
General safety
Information on recycling...








+ 	
   	
 

 	
  # 
 


	 	  

 4
5
6)
,



#7
Step 1
Open the dryer door by pressing
it as shown in the picture.
Step 2
Pull out the filter (using two
fingers).
Step 3
Clean off any fluff build-up on the
internal surface of the filter net.
Step 4
Replace the filter – never operate
the dryer without the...



	

=

	
		7
Step 1
Open the condenser cover
- grip the handle and pull
towards you.
Step 2
Remove the condenser by
turning the 3 catches, then pull
the condenser towards you. (It is
normal for some residual water
to be left in the tubes).
Step 3
Clean the condenser with running
water over the rear side to
remove any fluff deposits.
Step 4
Replace the condenser unit;
make sure that the unit is
securely in place, that all 3
catches...




*
	

 Install the dryer far from gas
ranges, stoves, radiators or
hobs, as flames may damage it.
If the dryer is installed below a
worktop, ensure there are 10
mm between the upper panel of
the dryer and any objects
above it, and 15 mm between
the sides of the machine and
the walls or furniture units
adjacent to it. This ensures
adequate air circulation.
>
 The room must be adequately ventilated while the dryer is
running. Make sure that the dryer is...



 button!
 	button
and indicator light


#









$


	%



&



$




%	

& (





#

	



?#  

5
	

buttons
and indicator
lights

#



indicator lights
indicator lights

)
!

*	
 

 


?@?55@1	 
Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in
function, the machine will switch off and the running cycle will reset.
%
#
	8
Allows for setting the programme: turn until the indicator points towards the desired programme (see Starting and selecting a
programme).
?	 	
Allow for selecting the options available for the selected programme. The relative indicator...


$
A
#	#
#

. Plug the dryer into the power supply socket.
/ Select the programme according to the type of laundry (see Laundry).
0 Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see
Care and maintenance).
1 Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door.
2 Press the ON/OFF button to start the machine.
3 After consulting the...

&


%
#


A@A
@%
 %
#
	
-


#

This programme is ideal for safely drying small loads in a short time, thereby optimising energy consumption. Suitable for loads of
up to /kg, it lasts about 37 minutes. The programme may last longer depending on the size and density of the load and on the
spin speed used during the wash cycle
We recommend checking whether garments are labelled with the 
 symbol and to turn them inside out before drying them.




#

This...


 !
8

#

This programme is designed for safely drying garments such as tracksuits and shorts bearing the  symbol. It is ideal for clothes
which do not need to be dried fully. Suitable for loads of up to 1kg, it lasts about 57	, although it may last longer
depending on the size and density of the load and of the spin speed used during the wash cycle. We suggest turning garments
inside out before drying them.
!
9#

#

This programme is designed for safely drying...

(


?	
The options allow for customising the selected programme according to one’s own needs.


The start of some programmes (see Programmes and options) may be delayed up to 6 hours. Press the button repeatedly to
enter the desired delay time. Before setting a delayed start, make sure that the water container is empty and that the filter is clean.


:$

When this option is selected, the drum rotates garments at intervals after the cold drying cycle has ended, in order to...