Indesit Wd 12 X Manual

							Model
WD 12 X
Dimensions
width 59,5 cm
height 81,5 cm
depth 54 cm
Capacity
from 1 to 5,5 kg for the wash programme; from 1 to 4 kg for the drying programme
Electrical
connectionsvoltage 230/240 Volt 50 Hz
maximum absorbed power 2050 W
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 46 litre
Spinning speed
up to 1200 rpm
Control programs
in compliance with
IEC regulation 456wash: programme 3; temperature 60C°; carried out with 5 kg load;
drying: run with a load of 2.5 kg and knob 
C et to position      .
This appliance conforms with the following E.E.C. directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent
modifications
Too much foam.
Is the detergent appropriate
for machine washing? Check
whether the definition on its
label reads “for machine wash”
or “hand and machine wash”,
or any other similar wording.
Is the correct amount being
used? An excessive amount of
detergent, besides producing
too much foam, does not
guarantee a more effective
wash, and causes scaling in the
internal parts of the appliance.
The washer-dryer does
not dry.
 Check whether:
the plug has been correctly
inserted into the socket; there
is electricity in your home; the
appliance door has been shut
properly; a delayed start (if
available) has not been
selected; programme knob A
has been set to position 
(Stop/Reset); the drying cycle
knob C has been set to
position 0.
The washer-dryer doesnt
dry properly.
 Check whether:
the end of the drain hose is
underwater; the drain pump is
obstructed; the advice given
on the maximum loads has
been taken; the water tap has
been turned on.
If, despite all checks, the washer-
dryer fails to function and the
problem persists, call your
nearest authorised Customer
Service Centre, providing the
following information:
- the nature of malfunction
- the model type no. (Mod. ....)
-   the serial number (S/N ....)
This information can be found on
the data plate situated at the back
of the washer-dryer.
Is there space between the
machine and adjacent
units? If it is not a built-in
model, the washer-dryer will
oscillate a bit during the spin
cycle. A few cm of space
should therefore be left
around it.
The washer-dryer leaks.
Is the metal ring of the inlet
hose properly attached?
Turn off  the water supply,
unplug the appliance and try
tightening its attachment
without forcing it.
Is the detergent dispenser
obstructed? Remove and
wash it under tap water.
Is the drain hose well
attached? Turn off the water
supply, unplug the appliance
and try tightening its
attachment.
Is the washer-dryer’s drain
duct clogged? Is there an
extension of the drain hose?
If so, is it positioned
incorrectly, blocking the
water flow?
Excessive vibration
during the spin cycle.
Have all transit screws been
removed durind instal-
lation? See the following
page on installation
procedures.
Has the washer-dryer been
levelled correctly? The
levelling of the appliance
should be checked
periodically. Adjust the feet
and check them with a level.
The washer-dryer does
not drain or spin.
Does the selected
programme incorporates
water draining? Some
programmes stop at the end
of the wash cycles and
draining will have to be
selected manually.
Is the “Easy iron  function
-where provided - enabled?
This function requires manual
selection for draining.
Is the drain hose kinked?
The tract of the drain hose
must be as straight as
possible. Make sure the drain
hose is not squashed or
kinked.
Technical characteristics
Always get
assistance from
authorised
technicians and
always insist on
original spare parts.
Instructions for installation and use  10 
						

							11  Instructions for installation and use
When the new washer-
dryer arrives
Installation and removal
Whether new or just  transported to a new house,
installation is extremely important for the correct
functioning of your washer-dryer.
Connecting the drain hose
The drain hose (hooked pipe) is
secured to the rear of the machine
by support clips and may be
routed to right or left as required.
The hook to be used in case the drain
hose ends at a height below 60 cm.
The drain hose should be placed
in a stand pipe with a minimum
internal diameter of 38 mm (1½
inches) or it can be positioned over
a sink or it can be connected as
shown in Fig. A. The height of
stand pipe or sink should be
between 60 and 100 cm (24 and
40 inches). Care must be taken
that the hose is not obstructed,
twisted, submerged or kinked. If
the hose is connected with an
airtight joining, provision should be
made to prevent syphoning.
The guide for draining into tubs and
sinks.
Fig. A
After removing the appliance from
its packaging, check that it is
intact. If in doubt, contact a
qualified technician immediately.
The inside of the machine is
supported, for transportation, by
four screws on the back panel.
Before using the washing
machine, remove the screws,
remove the spacers together with
the rubber tubes attached to them
(keeping all the parts) and use the
plastic plugs provided to fill in the
holes.
Important: Use the cap (provided)
to close the 3 holes which housed
the stop pin, situated in the right-hand
part of the lower back of the
washing machine.
Levelling
The washing machine must be
levelled appropriatey in order to
guarantee its correct functioning. To
level the appliance, the front feet
must be adjusted; the angle of
inclination, measured according to
the worktop, must not exceed 2°.
When placed on carpet, make sure
the ventilation is not reduced.
The front feet are adjustable.
Connection to the water
mains
Both hot and cold water supplies
are preferable and they should be
between 34.5kN/m²(5lb/in²) and
1034.2kN/m² (150lb/in²) pressure.
The hose having the red end fitting
should be encountered between
the hot supply and the threaded
connection adjacent to the letter H
on the rear of the machine. The
hose having the white end fittings
should be connected between the
cold supply and the threaded
connection adjacent to the letter C
on the rear of the machine.
Remember to insert a sealing
washer at each connection to
ensure watertight joints.  Do not
overtighten the connections by
using tools -hand tight is sufficient
to prevent leaks. It is generally more
convenient to have these supplies
away from the sink taps.  Where
no suitable hot water supply is
available or it does not meet these
requirements, both inlet hoses may
be connected to a cold supply by
using two taps etc., or a «T»
junction on the plumbing however,
use of cold water only will increase
programme times.
Note: the maximum temperature
should not exceed 70°C (158°F).
The rubber gasket.
Connect the inlet hose to the
threaded connector on the
machine rear.
Water pipe inlet at the top right.
Warning!
The company denies all
liability if and when these
norms are not respected.
Plastic bags, expanded
styrofoam, nails and other
packaging parts are not
children’s toys, and are
potentially dangerous.
Retain the transit screws,
spacers and washers.
Should you move house
then these should be
replaced to support the
inside of the machine to
prevent damage when
transporting the machine.
Electric connection
Your appliance is now supplied
with a 13 amp fused plug it can
be plugged into a 13 amp socket
for immediate use. Before using
the appliance please read the
instructions below.
WARNING - THIS APPLIANCE
MUST BE EARTHED.
THE FOLLOWING OPERATIONS
SHOULD  BE CARRIED OUT BY A
QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a
13 amp ASTA approved fuse to
BS 1362 should always be used,
and the fuse cover re-fitted. If the
fuse cover is lost, the plug must
not be used until a replacement
is obtained.
Replacement fuse covers:
If a replacement fuse cover is
fitted, it must be of the correct
colour as indicated by the
coloured marking or the colour
that is embossed in words on the
base of the plug. Replacements
can be obtained directly from
your nearest Service Depot. 
						

							Instructions for installation and use  12
Removing the plug:
If your appliance has a non-
rewireable moulded plug and you
should wish to re-route the mains
cable through partitions, units
etc., please ensure that either:
the plug is replaced by a fused
13 ampere re-wearable plug
bearing the BSI mark of approval.
or:
the mains cable is wired directly
into a 13 amp cable outlet,
controlled by a switch, (in
compliance with BS 5733) which
is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of
the plug itself, you make the pins
unusable so that it cannot be
accidentally inserted into a
socket.
Instructions for connecting
cable to an alternative plug:
Important: the wires in the
mains lead are coloured in
accordance with the following
code:
Green & Yellow     Earth
Blue                  Neutral
Brown                  Live
As the colours of the wires in the
lead may not correspond with the
coloured markings identifyng the
terminals in your plug, proceed as
follows:
Connect Green & Yellow wire to
terminal marked E or 
 or
coloured Green or Green & Yellow.
Connect Brown wire to terminal
marked L or coloured Red.
Connect Blue wire to terminal
marked N or coloured Black.
If a 13 amp plug (BS 1363) is used
it must be fitted with a
13 amp fuse, either in the plug or
adaptor or at the distribution board.
If you are in any doubt the
electrical supply to your machine,
consult a qualified electrician
before use.
How to connect an alternati-
ve plug:
The wires in this mains lead are
coloured in accordance with the
following code:
BLUE        NEUTRAL (N)
BROWN        LIVE (L)
GREEN & YELLOW     EARTH (E)Disposing of the appliance:
When disposing of the appliance
please remove the plug by
cutting the mains cable as close
as possible to the plug body and
dispose of it as described above.
GREEN &
YELLOW
BROWN
BLUE13 ampere fuse
CROSS-BAR
CORD GRIP 
						

							13  Instructions for installation and use
Mounting the wooden panel
onto the door and inserting
the machine into cabinets:
In the case where the machine
must be shipped for final
installation after the wooden
panel has been mounted, we
suggest leaving it in its original
packaging. The packaging was
designed  to make it possible to
mount the wooden panel onto
the machine without removing it
completely (see figures
below).The wooden panel that covers
the face of the machine must not
be less than 18 mm in
thickness and can be hinged on
either the right or left. For the
sake of practicality when using
the machine, we recommend
that the panel be hinged on the
same side as the door for the
machine itself - the left.Door Mounting Accessories
(Fig. 1-2-3-4-5)
- No. 6 type A self-threading
screws, l =13 mm.
- No. 2 type B metric,
countersunk screws, l =25; for
fastening the magnet plate to the
cabinet.
- No. 4 type C metric screws,
l =15 mm; for mounting the hinge
supports to the cabinet.
- No. 4 type D metric screws,
l =7 mm; for mounting the hinges
on the supports.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
N° 2 Hinges
N° 1 MagnetN° 1 Magnet plate
N° 1 Rubber plug N° 2 Hinge Supports
Instructions for the fitter
AB
CD
E
1 23456
lavabiancheriawashing machinemachine  laverwaschmaschine
Lato portaDoor side
Cote porteTur  seite
1 23456
lavabiancheriawashing machinem
ach
in
e   laverwaschmaschine
L
a
to
 p
o
rtaDoor side
Cote porteT
u
r  s
e
ite
Fig. 4/BN° 1 Spacer 
						

							  Instructions for installation and use  14
Mounting the Parts onto the
Face of the Machine
- Mount the hinge supports onto
the face of the machine,
positioning the hole indicated by
the arrow in fig. 1 towards the
inside of the face and using the
type C screws.
- Mount the magnetic plate on
the opposite side, at the top,
using the two type B screws.
- Place the spacer illustrated in
fig. 4/B between the appliance
front and the magnet receiver.
Using the Drilling Template
- To trace the positions of the
holes on the left-hand side of the
panel, align the drilling template
to the top left side of the panel
using the lines traced on the
extremities as a reference.
- To trace the positions of the
holes on the right-hand side ofthe panel, align the drilling
template to the top right side of
the panel.
- Use an appropriately sized
router to mill the holes for the two
hinges, the rubber plug and the
magnet.
Mounding the Parts onto the
Wooden Panel (Door)
- Insert the hinges into the holes
(the movable part of the hinge
must be positioned facing away
from the panel) and fasten them
with the 4 type A screws.
- Insert the magnet into the top
hole on the opposite side of the
hinges and fasten it with the two
type B screws.
- Insert the rubber plug into the
bottom hole.
The panel is now ready to be
mounted onto the machine.
Mounting the Panel into the
machine
Insert the nib of the hinge
(indicated by the arrow in fig. 2)
into the hole for the hinge and
push the panel towards the front
of the machine.  Fasten the two
hinges with the type D screws.
Fastening the plinth guide
If the machine is installed at the
end of a set of modular cabinets,
mount either one or both of the
guides for the base molding (as
shown in fig. 8). Adjust them for
depth based on the position of
the base molding, and, if
necessary, fasten the base to
the guides (fig. 9).
This is how to assemble the
plinth guide (fig.8):
Fig. 6 Fig. 7 Fig. 9
D
C
C
Adjusting the appliance height
The height of the appliance can
be adjusted (from 815 mm to
835 mm), by turning the 4 feet.
Should you require the
appliance to be placed higher
than the above height, you need
to use the following accessories
to raise it to up to 870 mm:
- the two crossbars  (G)
- the 4 feet (H)
- the 4 screws (I)
- the 4 nuts (L)
then perform the following
operations (fig. 11):
remove the 4 original feet, place
a crossbar G at the front of the
appliance, fastening it in place
using screws I (screwing them
in where the original feet were)
then insert the new feet H.Repeat the same operation at
the back of the appliance.
Now adjust feet H to raise or
lower the appliance from 835
mm to 870 mm.
Once you have reached the
desired height, lock nuts L onto
crossbar G.
Fig. 11
L
I
HG
To adjust the appliance to a
height between 870 mm and 900
mm, you need to mount strip M,
adjusting feet H to the required
height.
Insert the strip as follows:
loosen the three screws N
situated at the front of the Top
cover of the appliance, insert
strip M as shown in fig. 12, then
fasten screws N.Accessories provided for the
height adjustment
The following can be found inside
the polystyrene lid (fig. 10):
2 crossbars (G),
1 strip (M)
the following can be found inside
the appliance drum:
4 additional feet (H),
4 screws (I),
4 screws (R),
4 nuts (L),
2 plinth guides (Q)Fasten angle P using screw R,
insert plinth guide Q into the
special slot and once it is in the
desired position, lock it in place
using angle P and screw R.
Inserting the machine into the
Cabinet
- Push the machine into the
opening, aligning it with the
cabinets (fig. 6).
- Regulate the adjustable feet to
raise the machine to the
appropriate height.
- To adjust the position of the
wooden panel in both the
vertical and horizontal
directions, use the C and D
screws, as shown in fig. 7.
Important: close the lower part
of the appliance front by
ensuring that the plinth rests
against the floor.
Fig. 10
Fig. 12 Fig. 8
M
570min
815
540595
820 ÷ 900
600 min 
						

							Treat your machine well and it will provide
many years of trouble free service
Easy Care and Maintenance
Your washer-dryer is a reliable companion in life and on the job. It is just as important for you to keep it in
shape.
Your washer-dryer is designed
to provide reliable service over
many years. A few simple steps
will help to prolong its life and
avoid problems. It is advisable,
to turn off water taps when the
machine is not to be used, this
protects the hoses, etc.
If the water in your area is too
hard, use a deliming product
(water is hard if it often leaves
whitish stains around taps or
drains, especially of bath tubs.
For more accurate information as
to the type of water in your
system, call the local water
works or a local plumber).
Pockets must always be
emptied removing even pins,
badges and any other hard
object.
The washer-dryer exterior
should be cleaned with a rag
dipped in lukewarm water and
soap.Never exaggerate with doses.
Normal detergents already
contain deliming agents. Only if
the water is particularly hard,
that is, rich in lime content, do
we recommend the use of a
specific product at every wash.
A periodical wash cycle with a
dose of a deliming product,
without detergents or washing,
may prove useful.
Never use too much detergent
or additives because this could
cause an excess amount of
foam, scaling and possible
damage to the component parts
of your washer-dryer.
When in need, check the pump and the rubber hose.
The washer-dryer comes equipped with a self-cleaning pump that does not require any cleaning or maintenance.
The water inlet hose
Check the rubber hose at least once a year. If you see any cracks, replace it immediately. When you use your washer-dryer,
water pressure is very strong and a cracked tube could easily split open.
It is important to wash
the detergent dispenser
regularly.
To prevent dried washing
powder from
accumulating, place the
dispenser under running
water for a few minutes.
Do not forget to empty all pockets: small objects can
cause damage to your washer-dryer.
15  Instructions for installation and use 
						

							  Instructions for installation and use  16
Your safety and that of
your family
Important for the safe use of your washer-dryer
Your washer-dryer has been built  in compliance
with the strictest international safety regulations.
To protect you and all your family.
Read these instructions and all
the information in this manual
carefully: they are an important
source, not only of numerous
useful tips, but also of vital
information on safety, use and
maintenance.
1. the machine should not be
installed in an outdoor
environment, not even
when a roof shelters the
area, because it may be very
dangerous to leave it
exposed to rain and
thunderstorms.
2. It must only be used by
adults and  exclusively for
washing clothes following
the instructions provided in
this manual.
3.Should it have to be moved,
proceed with the help of two
or three people and handle
it with the utmost care.
Never try to do this alone,
because the appliance is
very heavy.
4.Before loading the washer-
dryer, make sure the drum
is empty.5. Never touch the washer-
dryer when barefoot or
with wet or damp hands
or feet.
6. Never use extensions or
multiple plugs, which  are
particularly dangerous in
humid environments. The
power supply cable must
never be bent or
dangerously compressed.7. Never open the detergent
dispenser while the
appliance is functioning;
do not use hand wash
detergent because the
abundance of foam  could
damage its internal par ts.8. Never pull on the supply
cable or the washer-dryer to
disconnect it from the wall
socket: it is extremely
dangerous.
9.While the appliance is
functioning, do not touch
the drain water  as it could
reach very high tempera-
tures.  The appliance door,
during wash cycles, tends
to become hot; ensure
that children do no touch
it. Never force the washer-
dryer door because this
could damage the safety
lock which prevents
accidental opening when the
nachine is working. Allow a
few minutes at the end of the
program for the lock to
release.
10. In case of malfunctioning,
first close the water tap
and unplug the appliance
from the wall socket; do
not under any circum-
stances touch internal parts
in order to attempt repairs.
I only want an authorised
specialised technician with
original  Indesit spare parts!
How to change the power supply cable
The washing machine
power supply cable is
special and can be purchased
exclusively from authorised
Technical Service Centres.
To replace the cable:
1. Make sure that the machine
is switched off and unplugged.2. Remove the cover by
unscrewing screws I [fig 13].
3. Disconnect the wires from
the radio interference
suppressor F [fig. 14] noting as
to their position (Blue=N wire;
Brown=L wire) leaving the
earth wire until last 
.
N.B.: letters L, N and the
symbol 
 are indicated on theradio interference suppressor.
4. Remove the screw and
washer V [fig. 15], which act as
a stop for the cable passageway.
5. Remove the upper part of the
cable slightly from the back
panel of the appliance, pull the
power supply cable upwards and
take it out [fig. 16].To connect  the new power
supply cable, reverse the pro-
cedure.
It is important for your
safety that you reassemble
all parts and screws used.
Fig. 13 Fig. 14 Fig. 15 Fig. 16
N
L
F 
						

							17  Instructions for installation and use
Were as close to you as your telephone
For direct access to Genuine Indesit Spare Parts and Accessories,
call 0870 558 5850 and speak to our skilled staff who can help you to identify and purchase the item you require.
For a Rapid Response to a problem with your appliance, call 0870 607 0805. Were open from Monday to
Saturday (8am - 5.30pm weekdays, 9am - 5pm Saturday). We have our own department of highly trained Indesit
service staff. For most calls, our Service Engineer can fix the problem on the first visit.
Please have the following details to hand when you ring us:
The nature of the problem, the Model Number and the Serial Number.
These numbers can be found on the appliance and on the portion of the Registration Card which you retain.
Stay in touch
THANK YOU for choosing an Indesit appliance. We are confident
you have made a good choice and that your new appliance will give
many years of excellent service.
And were there when you need us.
Register your purchase
now
This will confirm your entitlement to enter our quarterly prize draw
where you have the possibility to recover the cost of your purchase.
Simply complete and return the Registration Form supplied with the
appliance documents, using the FREEPOST envelope supplied. Or
call the Registration Hotline on 0870 010 4305. 
						

							  Instructions for installation and use  18 
						

							02/2002 -  195033265.00 - XEROX BUSINESS SERVICES - DOCUTECH
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel  +39 0732 6611
Fax +39 0732 662501
www.merloni.com
Leader for young Europe