InFocus LP1200 Projector User Manual

							21
ENGLISH
U OPTION
MOTION/STILL . Select MOTION when motion images are mainly projected.  Select STILL when still images
such as PC-CARD images are mainly projected.  It works only when inputting personal
computers of SXGA signals or inputting video signal.
SQUEEZE ........... Set to switch the normal image (4:3) and HDTV (16:9) automatically or not, depending on the
image signals.
MENU POSITION .Use to select the position where the menu is displayed (top or bottom on the screen).
AUTO POWER OFF ..Use to select the length of time before the projector switches to standby when there is no
input signal selected source. Select OFF to cancel this function.
REMOTE POSITIONSelect either FRONT or REAR to receive the infrared signal from the remote control. Select
AUTO for normal setting.
Note:When the remote position is changed with AUTO setting, the buttons cannot be
operated for about 3 seconds.
SIGNAL .............. When AUTO is set, the appropriate video standard is automatically selected according to the
input signal. If the image does not appear correctly, select the desired video standard
manually. Adjust the unit to the appropriate format when the unit either is not projecting
normally in auto mode or is inputting PAL-M/PAL-N signals.
RGB OUTPUT .... Use to select the output image from the personal computer terminal (RGB OUT).  When
selecting AUTO, the terminal images which signals are input are projected.  When a video
signal or PC card is displayed, the unit will project the image sent from the PC input terminal
last displayed.
LANGUAGE ....... Use to select the language for the projector display such as menu.
8 Ver.
Ver. ...............................Displays the version of the installed software.
MOTION
/STILLMENU
POSITIONAUTO
POWER OFFREMOTE
POSITIONVIDEO
SIGNALRGB
OUTPUTSQUEEZELANGUAGE
min.
English
Español
Deutsch
Français
ItalianoAUTO
MOTION
STILLAUTO
NTSC
PAL
SECAM
4.43NTSC
PAL-M
PAL-NAUTO
RGB1
RGB2 ON
OFF1
2ON
OFF5FRONT
REAR
OPTION Ver. INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
Ver. 3.3Ver.
OPTION INSTALLATION AUDIO LECT AUTO
CARTES PC 2 SOURCES
/ ZOOM IMAGE INITIALISATION 
						

							22
ENGLISH
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers.  In this case, press AUTO POSITION
button.  If the images are still not projected correctly,
use MENU display to adjust the projected images
from personal computers.  Also available to memorize
the setting.
Adjusting the images form personal
computers in MENU display
Adjust as below for the following symptoms.
Image moves to right or left :
Adjust HORIZ. POSITION in SIGNAL menu.  Press
the ¼ button on the control panel (or } button on
the remote control) to move the image to left.  Press
the » button on the control panel (or { button on
the remote control) to move the image to right.
Image moves to up or down :
Adjust VERT. POSITION in SIGNAL menu.  Press
the ¼ button on the control panel (or } button on
the remote control) to move the image to upward.
Press the » button on the control panel (or {
button on the remote control) to move the image to
down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise etc. appears on right or left side of image:
Adjust HORIZ. PIXELS of the menu in SIGNAL -
USER menu.
Noise etc. appears on top or bottom part of image :
Adjust VERT. LINES of the menu in SIGNAL -
USER menu.
Top part of image curves :
Change the setting of PLL or HOLD of the menu in
SIGNAL - USER menu.
PLL ....... Select FAST, NORMAL, or SLOW for
image which top part is the least curved.
Select AUTO for normal setting.
HOLD ... Select ON, and adjust BEGIN or END
for image which top part is the least
curved.Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL - USER
menu.  Select AUTO for normal setting.
¥ Do not change each menu setting in SIGNAL -
USER menu for normal setting.
Memorizing the setting
1. Select MEMORIZE in SIGNAL menu, and press
ENTER button.
2. Press the 
button on the control panel (or %
button on the remote control).
3. Press the» or ¼buttons on the control panel (or
{ or } buttons on the remote control) to select
the memory which you wish to record (USER 1 or
USER 2)
4. Press ENTER button.
Initializing the setting which has been changed
Select RESET in SIGNAL menu, and press ENTER
button.
¥  While initializing, buttons do not work about 2 -
18 seconds.  Use them to operate after initializing
is finished.
Seeing images in recorded setting.
Select AUTO in SIGNAL menu, and press the» or
¼buttons on the control panel (or { or } buttons
on the remote control) to select the memory (USER1
or USER2).
Resetting the recorded setting
1. Select DELETE in SIGNAL menu, and press
ENTER button.
2. Press the 
button on the control panel (or %
button on the remote control).
3. Press the» or ¼ buttons on the control panel (or
{ or } buttons on the remote control) to select
the memory which you wish to reset (USER 1 or
USER 2).
4. Press ENTER button
The recorded setting will be deleted.
The simple way of adjustment
1. Horizontal position:
Adjust the start position (the left end) using
HORIZ. POSITION, and adjust the end position
(the right end) using TRACKING.  Then repeat
these steps.
2. Vertical position:
Adjust the start position using VERT. POSITION.
AUTO AUTO
USER1
USER2SXGA70a000RGB
Y,CB,CRUSER
HORIZ.
POSITIONVERT.
POSITIONFINE SYNC. TRACKINGRGB/Y,CB,CR
0MEMORIZE
DELETE
RESET
OPTION Ver. INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
Picture adjustment
3333
33
33333333AUTO AUTO
ON
OFFAUTOBEGIN
CLAMP
POSITIONCLAMP
WIDTHHORIZ.
PIXELSVERT.
LINESVERT.
SYNC.SIGNAL - USERPLL HOLD
33
ENDON
OFF FAST
NORMAL
SLOW 
						

							23
ENGLISH
Specification of RGB signals in each computer mode of the projector
Signal mode resolution horizontal Vertical Normal Native (H x V) frequency (kHz) frequency (Hz) (H x V)  (H x V)
TV60 Ð 15.73 59.94 1024 x 768 (640 x 480)
TV50 Ð 15.63 50.00 1024 x 768 (640 x 480)
HiVision Ð 33.75 60.00 1024 x 576 (882 x 496)
PC98 640 x 400 24.82 56.42 1024 x 640 640 x 400
CGA70 640 x 400 31.47 70.09 1024 x 640 640 x 400
CGA84 640 x 400 37.86 84.13 1024 x 640 640 x 400
CGA85 640 x 400 37.86 85.08 1024 x 640 640 x 400
VGA60 640 x 480 31.47 59.94 1024 x 768 640 x 480
VGA72 640 x 480 37.86 72.81 1024 x 768 640 x 480
VGA75 640 x 480 37.50 75.00 1024 x 768 640 x 480
VGA85 640 x 480 43.27 85.01 1024 x 768 640 x 480
SVGA56 800 x 600 35.16 56.25 1024 x 768 800 x 600
SVGA60 800 x 600 37.88 60.32 1024 x 768 800 x 600
SVGA72 800 x 600 48.08 72.19 1024 x 768 800 x 600
SVGA75 800 x 600 46.88 75.00 1024 x 768 800 x 600
SVGA85 800 x 600 53.67 85.06 1024 x 768 800 x 600
XGA43i 1024 x 768 35.52 86.96 1024 x 768 1024 x 768
XGA60 1024 x 768 48.36 60.00 1024 x 768 1024 x 768
XGA70 1024 x 768 56.48 70.07 1024 x 768 1024 x 768
XGA75 1024 x 768 60.02 75.03 1024 x 768 1024 x 768
XGA85 1024 x 768 68.68 85.00 1024 x 768 1024 x 768
SXGA70a 1152 x 864 63.85 70.01 1024 x 768 1024 x 768
SXGA75a 1152 x 864 67.50 75.00 1024 x 768 1024 x 768
SXGA85a 1152 x 864 77.49 85.06 1024 x 768 1024 x 768
SXGA60a 1280 x 960 60.00 60.00 1024 x 768 1024 x 768
SXGA75a 1280 x 960 75.00 75.00 1024 x 768 1024 x 768
SXGA43i 1280 x 1024 46.43 86.87 960 x 768 1024 x 768
SXGA60 1280 x 1024 63.98 60.02 960 x 768 1024 x 768
SXGA75 1280 x 1024 79.88 74.94 960 x 768 1024 x 768
SXGA85 1280 x 1024 91.15 85.02 960 x 768 Ð
UXGA48i 1600 x 1200 62.50 96.08 1024 x 768 Ð
UXGA60 1600 x 1200 75.00 60.00 1024 x 768 Ð
UXGA65 1600 x 1200 81.25 65.00 1024 x 768 Ð
UXGA70 1600 x 1200 87.50 70.00 1024 x 768 Ð
UXGA75 1600 x 1200 93.75 75.00 1024 x 768 Ð
UXGA80 1600 x 1200 100.00 80.00 1024 x 768 Ð
UXGA85 1600 x 1200 106.25 85.00 1024 x 768 Ð
MAC13 640 x 480 35.00 66.67 1024 x 768 640 x 480
MAC16 832 x 624 49.72 74.55 1024 x 768 832 x 624
MAC19 1024 x 768 60.15 74.91 1024 x 768 1024 x 768
MAC21 1152 x 870 68.59 74.96 1024 x 768 1024 x 768
HP75 1024 x 768 62.94 74.92 1024 x 768 1024 x 768
HP72 1280 x 1024 78.13 72.00 960 x 768 1024 x 768
SUN66a 1152 x 900 61.85 66.00 984 x 768 1024 x 768
SUN76a 1152 x 900 71.81 76.64 984 x 768 1024 x 768
SUN66 1280 x 1024 71.68 66.68 960 x 768 1024 x 768
SUN76 1280 x 1024 81.13 76.11 960 x 768 1024 x 768
SGI72 1280 x 1024 76.92 72.30 960 x 768 1024 x 768
SGI76 1280 x 1024 82.00 76.00 960 x 768 1024 x 768
IBM60 1280 x 1024 63.42 60.00 960 x 768 1024 x 768
¥ *1 : As a result of line reduction in the projection
process with the computer models listed above,
lines and portions of characters found in the
original data may be missing from the projected
image.
¥ When the ZOOM MODE of PinP/EXPAND menu is
set to 4, by pressing the EXPAND button on the re-
mote control, it will switch to the screen displaying
the picture as its original size (real screen display).
In the real screen display, pictures will be black-
framed when picture resolution is lower than 1,024
x 768.Important:
¥ Some computers may not be compatible with the
projector.
¥ The projectors maximum resolution is 1,024 x 768
pixel.  It may not be displayed correctly for the pic-
tures of higher resolutions than 1,024 x 768.
¥ The picture with a SYNC on G (Green) signal
may vibrate.
¥ The picture with a SYNC on G (Green) signal may
be tinged with green.
*1
*1
*1
*1
*1
*1
*1
*1 
						

							24
ENGLISH
GAMMA CORRECTION menu
The proportion of the brightness of input signals to that of output signals can be corrected effectively by adjusting
GAMMA.
1. Select  GAMMA CORRECTION of PICTURE menu
and then press the ENTER button. (The GAMMA
CORRECTION menu appears on-screen display.)
Horizontal axis: brightness of the input signals
Vertical axis: brightness of the output signals
Inclination: GAMMA
2. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
MASTER.
3. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select the
points brightness of the input signals.
4. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control) to adjust
the brightness of the output signals.
5. Repeat steps 3 and 4 for another point setting.
10 0 203040506070 80 90100
GAMMA CORRECTION - USER
MASTERR
G
B
RESET
10 0 203040506070 80 90100
GAMMA CORRECTION - USER
MASTERR
G
B
RESET
GAMMA CORRECTION - USER
RESET10 0 203040506070 80 90100
MASTERR
G
B
GAMMA CORRECTION - USER
RESET10 0 203040506070 80 90100
MASTERR
G
B
If you wish to change the color balance, follow the steps
below.
6. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
MASTER, and then press the » or ¼ buttons on
the control panel (or { or } buttons on the remote
control) to select the desired color R, G or B.
7. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select the
points brightness of the input signals.
8. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control) to adjust
the brightness of the output signals.
9
.Repeat steps 7 and 8 for another point setting.
10.Press the ENTER button.
11.Exit the menu system by pressing the MENU but-
ton several times.
¥ To switch back to the default condition of GAMMA
CORRECTION, select RESET and press the EN-
TER button when the GAMMA CORRECTION dis-
play appears.
¥ When selecting RESET, the buttons cannot be oper-
ated for 2 to 18 seconds.
Picture adjustment (continue)
GAMMA CORRECTION - USER
RESET10 0 203040506070 80 90100
MASTERR
G
B
GAMMA CORRECTION - USER
RESET10 0 203040506070 80 90100
MASTERR
G
B
GAMMA CORRECTION - USER
RESET10 0 203040506070 80 90100
MASTERR
G
B 
						

							25
ENGLISH
Advanced feature for presentation
Cursor operation
1. Press the CURSOR button.
The cursor appears on the screen.
2. Press the START/STOP button to ON.
The operation indicator will be illuminated.
(The operation indicator will turn off if the remote
control is not used for a period of five minutes.)
3. Move the cursor by using the remote control.
4. Press the START/STOP button to momentarily
freeze the cursor movement. Press again to resume
moving.
5. Press the CURSOR button to cause the cursor to
disappear.
¥ When using the EXPAND mode, a red frame will
not appear if the cursor is selected.
To change the cursor size or the cursor moving
speed
1. Press the CURSOR button.
The cursor appears on the screen.
2. Press the START/STOP button to ON.
The operation indicator will be illuminated.
3. Press the DOUBLE CLICK button.
The tool icon appear on the screen.To draw line or frame
1. Press the CURSOR button.
The cursor appears on the screen.
2. Press the START/STOP button to ON.
The operation indicator will be illuminated.
3. Press the DOUBLE CLICK button.
The tool icon appear on the screen.
4. Move the cursor to where the point of form icon.
5. Press the SELECT button until the desired form is
appeared.
6. Move the cursor to where the point of Width icon.
7. Press the SELECT button until the desired width
of the line is appeared.
8. Move the cursor to where the point of Color icon.
9. Press the SELECT button until the desired color of
the line is appeared. (Red, Yellow, Green, Blue,
Purple, Black or White)
10.Press the DOUBLE CLICK button.
11 .Position the cursor where you want the path to be-
gin and press the SELECT button.
A red frame appears on the screen..
¥ The red frame will be disappeared by pressing
the CANCEL button.
12.Move the cursor to where you want the point of the
opposite corner and press the SELECT button again.
¥ By pressing the CANCEL button, the line or frame
will disappear.
¥ When the MENU appears, the cursor will disappear.
¥ When the cursor appears, the source ID will disappear.
¥ You can not adjust the zoom/focus in the cursor op-
eration mode.
¥ When using the EXPAND mode, a red frame will
not appear if the cursor is selected.
¥ The currently projected image will disappear in
the following cases: when PC card images are
updated, when alternating PinP or EXPAND
mode, or when display size is enlarged or
otherwise altered.
Still
How to stop the picture temporaly (still picture)
1. Press the ENTER/STILL button on the remote
control.
The picture will stop temporaly.
To stop still picture.
2. Press the ENTER/STILL button on the remote
control again.
¥ To release the still picture, Cursor, SELECT,
DOUBLE CLICK, CANCEL, and START/STOP
buttons also can be used.
SLOW FAST
4. Move the cursor to where the point of cursor size
icon.
5. Press the SELECT button until the desired size is
appeared.
6. Move the cursor to where the point of cursor speed
icon.
7. Press the SELECT button until the desired speed
is appeared.
8. Press the DOUBLE CLICK button.
Cursor size
ColorWidthForm
Cursor speed
........... Straight line 
........... Square
........... Rounded-square
........... Circle
........... Horizontal straight line 
Move
upward
Move
downward
Move to
right Move to
left 
						

							26
ENGLISH
Advanced feature for presentation (Continue)
Expand
By pressing the EXPAND button on the remote con-
trol, you can view the detailed image of the picture.
Setting the Expand mode
1. Press the MENU button once to display the on-
screen menu.
2. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
PinP/EXPAND.
3. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control).
4. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
ZOOM MODE, POSITION or SIZE.
5. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control) to set the
ZOOM MODE, POSITION or SIZE.
Normal picture
Actual size picture Zooming picture (ZOOM MODE1)
(ZOOM MODE4)
Zooming picture (ZOOM MODE3)
(ZOOM MODE2) ZOOM MODE
Zooming pictureNormal 
picture
6. Press the MENU button twice to exit the menu sys-
tem.
Using the Expand mode
1. Press the EXPAND button.
A red frame indicating EXPAND area will appear.
¥ You can magnify different areas of the active pic-
ture by pressing the  » , ¼,
 or buttons on
the control panel (or {, }, $ or % buttons on the
remote control).
¥ You can change the magnification of the zoomed
area by pressing the + or - buttons.
2. Press the EXPAND button again.
¥ In EXPAND mode, do not display the test pattern.
¥ In EXPAND mode (except in type 4 mode) you can-
not adjust the zoom/focus.
¥ Display enlargement does not work with video
input or S-video input.
¥ The red frame indicating EXPAND area will
disappear when the cursor is selected.
Indication Mode 4 (actual size display)
¥ Pressing the  » , ¼,
, buttons on the
control panel (or { , } ,$, % buttons on the
remote control) is for adjusting fine adjust, zoom
or focus.
¥ The expanding rate cannnot be changed either
pressing + or - button.
Super impose (Picture in Picture)
One of the special features of this unit is the picture-
in-picture (PinP) mode. PinP allows you to view differ-
ent sources at the same time. The sub image will be-
come a still picture.
1. Press the PinP button on the remote control.
¥ Pressing the PinP button repeatedly will select
on and off.
2. Select the desired external input source of the sub
image by using the RGB, VIDEO or CARD button.
¥ You can change the frame position and the frame
size by using the on-screen menu.
To recapture the picture of sub screen
3 Press the Ð  or + button.
¥ By each press of the button will recapture the
picture of  sub screen.
To switch Main image and sub image
4 Press the
 or buttons on the control panel (or
$ or % buttons on the remote control).
To switch still picture and playback picture between
Main image and Sub image
5 Press the » or ¼ buttons on the control panel
(or { or } buttons on the remote control) .
6. Press the PinP button on the remote control.
The sub image will be disappear.
¥ In PinP mode, the sub image will become still
pictures.  When the main image is set to PC1 or
PC2, the  sub image will become moving pictures.
¥ In PinP mode, the sound of the moving pictures will
be heard.
¥ The sub image may vibrate. If this is the case, select
the image again by pressing the Ô-Õ button.
¥ In PinP mode you cannot adjust the zoom/focus.
¥ Ajusting contrast, brightness, tint or color isnt
available in PinP mode.
¥ To use different PC card (PC card 1, PC card 2) on
both Main image and Sub image is not available.
¥ When the main and sub images are set to PC1 or
PC2, images can be selected only from the same
group of the same PC-CARD.
¥ By setting the AUTO PIP on the PinP/EXPAND
menu to ON, the position of the sub image will
move automatically when the red frame indicating
the EXPAND area overlap with the sub image. 
						

							27
ENGLISH
PC-CARD
The projector can play back an image by using the PC-
CARD.
Using the PC-CARD
Use only the flash memory card of PCMCIA¥ATA com-
patible type II.
¥ Due to PC-CARD type, some images can not be prop-
erly recorded.  Please contact your dealer.
Setting up the PC-CARD
1. Set the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
2. Open PC-CARD cover on the left side of the projec-
tor.
3. Make sure the PC card is going to be inserted in
right side.  The PC card
indicator of the PC card
which has been inserted
will illuminate.
4. Close the cover.
When the input source is set to
PC1 or PC2, or during recording to the PC card, do not
remove the PC card. The projector may not work cor-
rectly.
Release the PC-CARD
1. Press the RELEASE button on the remote control.
PC card eject icon will be displayed on the right
end of the screen.
The PC card indicator will turned off on the
projector.
2. Open PC-CARD cover on the left side of the projec-
tor.
3. Press the eject button to take the card out.
4. Close the cover.
¥ Upon removing a PC card, wait at least 2 seconds
before inserting another.
¥ When the input source is set to PC1 or PC2, or
during recording to the PC card, do not remove
the PC card. The projector may not work correctly.
¥ When having an access of PC card, PC card eject
prohibit icon will be displayed on the right end of
the screen.
¥ If you do not wish this icon to be indicated, turn
ICON on PC CARD menu to OFF.  In this case,
the icon appears when the RELEASE button is
pressed even the setting is OFF.
¥ PC card eject icon will be indicated till the card is
ejected. If you press the RELEASE button when
PC cards are inserted, you need to either take
both out or change one of the cards to the icon to
disappear.
¥ PC-CARD of the following manufacturers has been
confirmed of operation;
EPSON, TDK, Logitec, Panasonic, Verbatim, I-O
DATA.Play back
1. Insert the prerecorded PC-card.
2. Press the CARD button repeatedly until PC-1 (or
PC-2) appear on the screen.
The PC-CARD index display appears on the screen.
3. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select the
desired image.
¥ If the PC-CARD is recorded by using the per-
sonal computer, select the desired group by press-
ing the + or - button.
4. Press the » or ¼ button on the control panel (or
{ or } button on the remote control) to enter the
image display mode.
5. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to display
another image.
6.Press the VIDEO or RGB buttons to quit the PC-
CARD playback function.
7. Press the RELEASE button on the remote
control.
8. Press the eject button to take the card out.
¥ During PC-CARD playback, the sound is switched
off.
¥  Noise may occur momentarily when images are
updated via PC card.
¥ The images recorded in BMP (not compressed)
will take a long time to playback.
¥ It takes about 10 seconds to playback JPEG
compressed data.
¥ When having an access of PC card as you want to
exchage images on PC card, there will be four red
line indicated at the edge of the screen.
¥ When the main and sub images are set to PC1 or
PC2, images can be selected only from the same
group of the same PC-CARD. Other group or other
card will not be able to indicate simultaneously.
¥ If the PC card is ejected when playing back PC
card, the image will be switched to Video 1 picture
automatically.
¥ During PC-CARD playback, if the incorrect
display appears, release and re-insert the PC-
CARD.
Playback picture taken by the digital camera
¥ The image which has been recorded in PCMCIA/
ATA card, smart media or compact flash can be
playback.  The PC card adapter is required to
playback smart media and compact flash.
¥ Depending on the type of the digital camera,
picture will not appear correctly.  Please contact
your dealer.
¥ PC card recorded by Digital Camera, the picture
will not be diaplayed on PC-CARD index display. 
						

							28
ENGLISH
PC-CARD (Continue)
To automatically change the image, follow the steps
as shown below.
1. Press the MENU button.
2. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select PC
CARD AUTO  PLAY.
3. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control).
4. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
AUTO SLIDE TIME.
5. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control) to set the
time for auto playback.
6. Press the
 or buttons on the control panel (or
$ or % buttons on the remote control) to select
REPEAT.
7. Press the » or ¼ buttons on the control panel (or
{ or } buttons on the remote control) to select ON
or OFF.
8. Press the MENU button twice to exit the menu sys-
tem.
9. Press the CARD button repeatedly until PC-1 (or
PC-2) appear on the screen.
10. Press the or buttons  on the control panel (or
$ or % buttons on the remote control) to select the
desired image.
PC CARD
AUTO PLAY PinP/
EXPAND PICTURESIGNAL
PC CARD
AUTO PLAY PinP/
EXPAND PICTURESIGNAL
10 sec.ON
OFFON
OFF REPEAT
AUTO SLIDE
TIMEICON
INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
 10 sec.ON
OFFON
OFF
INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
REPEATAUTO SLIDE
TIMEICON
 30 sec.ON
OFFON
OFF
INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
REPEATAUTO SLIDE
TIMEICON
 30 sec.ON
OFFON
OFF
INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
REPEATAUTO SLIDE
TIMEICON
 30 sec.ON
OFFON
OFF
INSTALLATION AUDIO PC CARD
AUTO PLAY PinP/
EXPAND PICTURE SIGNAL
REPEATAUTO SLIDE
TIMEICON
11 .Press the AUTO PLAY button on the remote con-
trol.
The image automatically changes according your
setting.
12.Press the AUTO PLAY button on the remote con-
trol to quit the PC-CARD automatic playback func-
tion.
¥  A gray frame will appear during auto play.
¥  Button operation will only work when the gray
frame appears on screen. Button operation is not
possible while the red frame is on-screen.
¥  When projecting images in 2-screen display mode,
the screen will momentarily go black when images
inputted via PC card are updated.
¥  Auto play can be stopped by pressing any button
(including SELECT, DOUBLE CLICK, CANCEL,
and START/STOP).
¥  Auto play cannot be used either during image
enlargement or when menus are displayed. 
						

							29
ENGLISH
Advanced feature with PC
There are three types of application software provided.
1. PCV (PC Card Viewer)
2. PCGC (Personal Computer Graphic Controller)
3. SpacePointer (Driver for PC control by the remote
controller)
Environment
The following system software and hardware are nec-
essary to use the projector.
When you use Macintosh
¥ Macintosh series loading more than 68030 in
CPU and a video card with which more than
256 colors are available
¥ System7.1 or newer
¥ 8MB of Random-access memory (RAM) space
When you use Microsoft
¨ Windows¨
¥ Microsoft¨ Windows¨ 95 Operating System
(Windows 95) or Microsoft
¨ Windows NT¨
Operating System Version 4.0 (Windows NT) or
Microsoft
¨ Windows¨ Operating System
Version 3.1 (Windows 3.1)  with the CPU
loading more than 80486SX and a display card
with more than 256 colors are available
¥ 16MB or more of RAM available
¥ We recommend  the following hardware.
¥ 32MB or more of RAM available
¥ A video display card with full colors are
available
EXPORT LAW ASSURANCES
You acknowledge and agree that the SOFTWARE is subject
to restrictions and controls imposed by the United States
Export Administration Act (the ÒActÓ) and the regulations
thereunder. You agree and certify that neither the
SOFTWARE nor any direct product thereof is being or will
be acquired, shipped, transferred or reexported, directly or
indirectly, into any country prohibited by the Act and the
regulations thereunder or will be used for any purpose
prohibited by the same.
LIMITATIONS OF REMEDIES
Regardless of whether any remedy set forth herein fails of
its essential purpose, in no event will InFocus be liable to
you for any special, consequential, indirect or similar
damages, including any lost profits or lost data arising out
of the use or inability to use the SOFTWARE or any data
supplied therewith even if InFocus or anyone else has been
advised of the possibility of such damages, or for any claim
by any other party.
Some states do not allow the limitation or exclusion of
liability for incidental or consequential damages so the
above limitation or exclusion may not apply to you.
In no case shall InFocusÕs liability exceed the price for the
SOFTWARE.
A. PCV (PC Card Viewer)
PC-CARD viewer (PCV) is a utility software that lets
you record and project an  image to a PC-CARD by us-
ing a personal computer.
Installation of software
For Windows 95 or Windows NT
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Start up Program Manager.
Click the [Start] button and select the [Run (
R)] com-
mand. Then the [Run] dialog box is displayed.
4. If you inserted the CD-ROM to drive D, type [D:
Win95\Pcv\Us\Setup95] (Windows 95) or [D:
Winnt40\Pcv\Us\Setupnt] (Windows NT) in the
command line text box and click the OK button.
The letter [D] may be different according to the
drive you use.
5. When the setup program starts up, follow the on-
screen instructions.
6. When the message ÒCompletedÓ appears on screen,
click the [Finish] button to complete the installation.
¥ Installation of Microsoft Internet Explorer 3.02 (or
later) is required for optimum unit operation. Use
the Jaaxdist.exe command should the unit appear
to not be performing normally.
For  Windows 3.1
1.  Start up Windows.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Select the [Run (
R)] command on the icon menu so
that the dialog box [Run] is displayed.
4. If you inserted the CD-ROM to drive D, type
[D:Win31\Pcv\Us\Setup] in the command line
text box and click the OK button. The letter [D]
may be different according to the drive you use.
5. When the setup program starts up, follow the on-
screen instructions.
6. When the message ÒcompletedÓ appears on screen,
click the [OK] button to complete the installation.
For Macintosh
1. Start up Macintosh.
2. Insert the Projector driver CD-ROM into your CD-
ROM drive.
3. Copy PCV for MacÓ file in the ÒPCVÓ folder to
anywhere on the hard disk. 
						

							30
ENGLISH
Advanced feature with PC (Continue)
Starting up PCV (For Windows)
For Windows 95 or Windows NT
1. Start up Windows.
2. Insert the PC card to the PC Card slot on the per-
sonal computer.
3. Start up Program Manager.
Click the [Start] button and select the [Program
(
P)]Ô[Pcv]Ô[PCV]command.
For Windows 3.1
1. Start up Windows.
2. Insert the PC card to the PC Card slot on the per-
sonal computer.
3. Double click the [PCV] icon in the PCV folder.
Command reference (For Windows 95 or
Windows NT)
The command references are as shown below:
File
New presentation .... Create a new presentation.
Open presentation...Opens an existing presenta-
tion.
Close presentation ...Closes an opened presenta-
tion.
Save presentation .... Saves an opened presentation
using the same name.
Save presentation As... Saves an opened presentation
to a specified name.
Delete presentation .Delete an opened presenta-
tion.
E
xit ........................... Exits PCV.
Edit
Cu
t ............................Deletes selected image from
the presentation and moves it
to the clipboard.
Copy ..........................Copies selected image data
from the presentation to the
clipboard.
Paste .........................Pastesimage data from the clip-
board into the presentation.
Image
Add image
Image 
file... .........Inserts image file to an opened
presentation.
Screen 
capture... .Captures screen and inserts it
to an opened presentation.
Delete image... .........Deletes the selected image
from an opened presentation.
Image information...Displays information of the
selected image.
View
Tool Bar .................... Shows or hides the toolbar.
Drive Bar .................. Shows or hides the drivebar.
Status Bar ................Shows or hides the status bar.
Window
Cascade .................... Arranges windows in an over-
lapped fashion.
Tile 
Horizontal .........Arranges windows in non-
overlapped horizontal tiles.
Tile Vertical .............. Arrages windows in non-over-
lapped vertical tiles.
Arrange Icons ........... Arranges icons of closed win-
dows.
Windows 1, 2, ... ....... Goes to specified window.
Help
Help Topics ............... Offers you an index to topics
on which you can get help.
Advanced 
settings ....Displays a detail setting of
this application.
About PCV... ............. Displays the version informa-
tion of this application.
Command reference (For Windows 3.1)
The command references are as shown below:
File
New presentation .... Create a new presentation.
Open presentation...Opens an existing presenta-
tion.
Close presentation...Closes an opened presenta-
tion.
Save presentation... . Saves an opened presentation
using the same name.
Delete presentation...Delete an opened presentation.
Open 
image file... ..... Import an image from a file.
E
xit ........................... Exits PCV.
Edit
Cu
t ............................Deletes selected image from
the presentation and moves it
to the clipboard.
Copy .......................... Copies selected image data
from the presentation to the
clipboard.
Paste .........................Pastesimage data from the
clipboard into the presenta-
tion.
Tool
Capture ....................Captures screen and inserts it
to an opened presentation.
Delete image... .........Deletes the selected image
from an opened presentation.
View
Tool Bar .................... Shows or hides the toolbar.
Status Bar ................Shows or hides the status bar.
Option
Select card drive... ...Select (or change) the PC-
CARD drive.
Card drive 
info... ...... Display the information of the
selected PC-CARD drive.
Index image size... ... Select the size of index image.
Help
About PCV... ............. Displays the version informa-
tion of this application.