InFocus Projector In5312 User Manual

User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  21 and Setting the OSD Language  on page 22 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password, contact InFocus at...

IN5312/IN5314 – User’s Manual 
5.  Use the arrow buttons ▲▼◄► 
on either the keypad or remote control 
to enter a password. Any combination 
can be used, including the same arrow 
button, but you must use a 
combination of five arrow button 
presses. 
Push the MENU button  to exit the 
dialog box. 
 
 
6.  The password confirm menu appears 
when the user powers on the projector 
and the Security Lock feature is 
enabled.  
Enter the password in the order you 
set it at step 5. In case you forget the...

User’s Manual 
 Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•  The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Remove and discard the foam spacers on the rear leveling feet before adjusting the pro-
jection angle. 
•   Ensure the cables are in a safe location. You could trip over them.  
1.  To raise the level of the projector, 
twist the leveling feet clockwise. 
2.  To...

IN5312/IN5314 – User’s Manual 
Adjusting Projected Image Position Using Shift 
 
The Shift feature provides a lens shift function that can be used to adjust the  position of the projected 
image either horizontally or vertica lly within the range detailed below. 
Shift is a unique system that provid es lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can  be adjusted between 100% and 40%...

User’s Manual 
Adjusting the horizontal image position 
With the lens in the center position the horizontal image position can be adjusted to the left or right by 
up to a maximum of 5% of the image width. Note  that the maximum horizontal image height adjust-
ment can be limited by the  vertical image position. For example it is not  possible to achieve the 
maximum horizontal image position if  the vertical image position is at maximum. Please consult the 
Shift Range diagram below for further...

IN5312/IN5314 – User’s Manual 
Adjusting Zoom, Focus and Keystone 
1.  Use the Zoom ring to 
resize the projected im-
age and screen size. 
 
2.  Use the Focus ring to 
sharpen the projected 
image. 
 
3.  Use the KEYSTONE 
buttons (on the projec-
tor or the remote 
control) to correct im-
age trapezoiding (wider 
top or bottom). 
Remote control and OSD panel 
4.  The keystone control  
appears on the display. 
 
   – 19  –  

User’s Manual 
Adjusting the Volume 
1.  Press the Volume but-
tons (on the projector or 
the remote control). 
 
 
The volume control  
appears on the display.
 
2.  Use the Vol +/-  buttons 
(on the projector or the 
remote control). 
3.  Press the  MUTE button 
to turn off the audio 
(This feature is only 
available on the re-
mote). 
 
 
– 20 –   

IN5312/IN5314 – User’s Manual 
  – 21  – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the projector keyp ad to navigate and make changes to 
the OSD.  
 
1.  To enter the OSD, press the 
MENU button.  
2.  There are five menus. Press  the cursor  ◄► button to 
move through the menus.  
3. Press the cursor  ▲▼ button 
to move up...

User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor  ◄► button to navigate to  Installation I. 
 
2. Press the cursor ▲▼  button until Language is highlighted.  
3. Press the cursor ◄►  button until the language you want is selected.  
4. Press the MENU button to close the OSD.   
 
– 22 –   

IN5312/IN5314 – User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
 
 
   – 23  –