Inter-Tel Glx Installation And Field Maintenance Manual

INTER-TEL PRACTICES 
PROGRAMMING 
GLX INSTALLATION 6 MAINTENANCE 
Issue 1, November 1985 
PROGRAMMING 
CONTENTS PAGE 
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-l 
2. PROGRAM PLANNING SHEETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
4-l 
3. OUTLINE FOR PROGRAMMING NEW SYSTEMS..................... 4-4 
4. 
INITIALIZE THE SYSTEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
4-4 
5. PROGRAM THE...

INTER-TEL PRACTICES 
PROGRAMMING 
GLX INSTALLATION & MAINTENANCE 
Issue 1, 
November 1985 
* FIGURE 4-1. PROGRAM PLANNING SHEETS 
SYSTEM FEATURES 
Performed from the attendants keyset (intercom number 10). 
SYSTEM TIMERS: 
Enter numbers in seconds. If the timer is not 
desired, enter 0. 
Timer 
Code Desired Value 
Default Range 
Attendant Recall *11 180 sec. 0, 60-600 sec. 
Hold Recall *12 60 sec. 0, 15-300 sec. 
Inactivity *13 
15 sec. 0, 15-60 sec. 
FEATURE TIMERS: 
Enter numbers in tenths of a second...

INTER-TEL PRACTICES 
PROGRAMMING 
GLX INSTALLATION & MAINTENANCE 
Issue 1, 
November 1985 
FIGURE 
4-l. PROGRAM PLANNING SHEETS (CONTD) 
REYSET FEATURES 
Performed at individual keysets. 
(Place check marks in the 
appropriate boxes.) 
16 
17 
18 
19 
20 
! 
21 
i 
*Keyset options are: 
l- 
2‘- Incoming Page Disable 
Ring Intercom First 
. 
3 
- Night Answer 
4 - Speakerphone Activation Pre-select Disable 
6 
- Toll Restrict 
Page 4-3  

INTER-TEL PRACTICES PROGRAMMING 
GLX INSTALLATION & MAINTENANCE Issue 1, 
November 1985 
3. OUTLINE FOR PROGRAMMING NEW SYSTEMS 
3.01 A newly installed system is programmed 
1. 
Place the KSU PWR and PRG EN switches as follows: 
in the ON position. 
2. 
Initialize the system as described below. 
3. Program the system and keyset features as described on 
the following pages. 
4. Place the PRG EN switch in the OFF position when pro- 
gramming is completed. 
NOTE: It is important to return the PRG EN switch...

INTER-TEL PRACTICES 
PROGRAMMING 
GLX INSTALLATION h MAINTENANCE 
Issue 1, 
November 1985 
l System option 1 is enabled. 
l All C.O. lines are subject to toll restriction. 
l A call forward C.O. line is not preset. 
l All keysets can access all C.O. 
lines for outgoing calls. 
l No keyset options are preset. 
l System speed-dial numbers are erased. 
4.02 To initialize the system: 
CAUTION: 
This function returns the data base to default values. 
(1) Place the KSU PRG EN switch in the ON position. 
(2)...

INTER-TEL PRACTICES PROGRAMMING 
GLX INSTALLATION & MAINTENANCE Issue 1, 
November 1985 
A. SYSTEM FEilTURES PROGRAMMING 
5.02 The following procedures are used for programming the sys- 
tem features from the attendants keyset. For further explana- 
tions of the timers and features, refer to the FEATURES section. 
(1) Place the KSU PRG EN switch in the ON position. 
. 
(2) From the attendants keyset (intercom number lo), pro- ,. , I 
.: 
gram the system features as follows: ..‘. 
a. Attendant recall...

INTER-TEL PRACTICES PROGRAMMING 
GLX INSTALLATION & MAINTENANCE Issue 1, 
November 1985 
d. C.O. flash timer: This is the duration of the hook- 
flash generated when a line key or the FLASH key is 
pressed. A timed hookflash is used to disconnect 
calls without hanging up; it also allows users to 
access PBX or telephone company features. The timer 
is preset to 0.7 seconds during initialization. 
1. While on hook, dial *21. 
2. Enter the C.O. flash time in tenths of a second 
(2-12). (2 = 0.2 sec., 12 =...

INTER-TEL PRACTICES 
PROGRAMMING 
GLX INSTALLATION & MAINTENANCE 
Issue 1, 
November 1985 
9* Memory-dial speed timer: 
Some central offices and 
PBX systems cannot process speed-dialed and re- 
dialed numbers as quickly as the GLX System sends 
them (0.1 seconds per digit). 
This timer allows a 
0.1 second pause to be added after each digit to 
slow the dialing speed to 0.2 seconds per digit. 
The length of the DTMF tone is not affected; only 
the duration of the pause between digits is changed. 
~ ‘_:...

INTER-TEL PRACTICES PROGRAMMING 
GLX INSTALLATION & MAINTENANCE Issue 1, 
November 1985 
5 Exclude C.O. line from toll restriction: If a C.O. 
line is excluded from toll restriction, toll re- 
stricted keyset users can access the C.O. line for 
placing calls that would normally be denied. No 
C.O. lines are preset during initialization. 
I. While on hook, dial #4. 
2. 
Press the line key(s) of the C.O. line(s) that 
will not be subject to toll restriction. 
(To 
return to default status, skip this step.)...

INTER-TEL PRACTICES 
PROGRAMMING 
GLX INSTALLATION h MAINTENANCE 
Issue 1, 
November 1985 
Option 4 - Allow system speed-dial numbers to 
bypass toll restriction: 
Permits system speed- 
dial numbers to bypass the toll restrictions 
enabled by option 1, 
2, or 3. 
Because option 4 
modifies the other options, it is never used by 
itself. 
3. Lift and replace the handset. 
1. Call forward to public network: 
To allow keyset 
users to forward intercom and transferred calls to 
outside telephone numbers,...