Iwatsu Adix Vs Owners Manual

Digital Telephone User’s Guide - 39  
Digital Telephones – Basic Feature 
Operation 
This section describes basic feature operation from ADIX-VS Digital Telephones. 
Making an Outgoing Call 
Operation 
F Lift the receiver 
F Press the button for an outside line and the outside line button will 
flash green 
F Wait for the dial tone 
F Dial the telephone number 
 
If you make a dialing mistake, Press the Flash button FLASH and start 
over. 
Receiving an Incoming Call 
Operation 
When your phone rings and...

Digital Telephone User’s Guide - 40  Making an Intercom Call 
Operation 
F Lift the receiver  
F Wait for the dial tone 
F Dial the desired extension number 
Or 
F Press the button representing the desired extension if assigned as a 
Multipurpose button 
F Make an announcement after the tone or wait for an answer to the ring 
 
The lamp on the intercom button ICM will flash red.  If the extension you 
called is busy, you will hear a repeated intercom busy tone. 
Receiving an Intercom Call 
Operation 
F...

Digital Telephone User’s Guide - 41  Operation 
F Lift the receiver and remain off hook on intercom for a specific time 
period programmed in the system. 
Or 
F Lift the receiver to make an intercom call. Begin dialing. Between digits 
stop dialing for more than 10 seconds. 
Note:  If a user dials a valid trunk access or optimized routing access code, this feature will not activate. Or 
F Dial the E-Response Group access number when you hear the 
Intercom Dial Tone. 
Transferring a Call to Another...

Digital Telephone User’s Guide - 42  Putting a Call On Hold 
Operation 
When speaking on an outside line: 
F Press the Hold button HOLD/DND 
 
A green lamp flashes  intermittently on your phone and a red lamp flashes 
on other phones for that outside line.  If the call is on Hold too long, your 
phone will ring again. 
Picking Up a Call On Hold 
Operation 
F Lift the receiver 
F Press the green intermittently flashing button on your phone or the red 
flashing button on another phone representing the...

Digital Telephone User’s Guide - 43  To put a call on Call Park at another extension: 
When speaking on an outside line: 
F Press the Transfer button TRAN 
F Press the Call Park button PARK 
F Dial the extension number or press the DSS key or CCV key of the 
station at which you want to park the call.  
F Hang up 
 
F If the call is on Call Park too long your phone will ring. 
 
To pick up a call on Call Park at another extension: 
F Lift the receiver 
F Wait for the dial tone 
F Press the Feature button...

Digital Telephone User’s Guide - 44  Digital Doorphone Operation 
Digital Doorphones provide an economical and simple method to allow visitors to 
make an intercom call to gain entrance to your building. 
 
Operation 
To place a call from a Digital Doorphone: 
F Press and release the button on the Digital Doorphone, you will  hear a 
ringing tone and the lamp on the button will change from red to green 
F Wait for an answer  
F Announce yourself 
 
To call a Digital Doorphone: 
F Lift the receiver 
F...

Digital Telephone User’s Guide - 45  
Digital Telephones - Advanced Features 
Caller ID, ANI, DNIS Information Storage 
Allows you to store and display the telephone number for a call on a caller ID, ANI 
or DNIS line. The system may be programmed to save information for all calls, or 
abandoned calls only. 
Operation 
To view stored call information: 
F For station:   At ICM dial tone press the illuminated USAS key once 
to display information about the first call to your station. Press [*] to 
scroll...

Digital Telephone User’s Guide - 46  Absence Message Display 
Allows you to leave an advisory message for a display phone caller if you should 
leave your office.  Four messages are available: 
Return at (time) 
Return on (date) 
Meeting at (time) 
Call (number) 
This feature only works with a Multipurpose button programmed for Absence 
Message ABS.MSG 
 
Operation 
To register a message: 
F Press the Speaker button SPKR 
F Press the Absence Message button ABS.MSG 
 
For Return At: 
F Dial 1 then dial...

Digital Telephone User’s Guide - 47  Account Code 
Allows you to enter a one- to twelve-digit code to either identify the caller or identify 
the party the call was made for.  These codes are printed out with the SMDR 
information.  Account code entry may be done before the party answers, during a 
conversation, or after the other party hangs up. 
 
Operation 
F Lift the receiver 
F Press an outside line button 
F Wait for the dial tone 
F Press the Feature button FEAT then dial 25 
Or 
F Press the...

Digital Telephone User’s Guide - 48  Operation 
To scroll or change the information on the display during a conversation: 
F Press the Feature button FEAT then dial 63 
Or 
F Press the Display button DISPLAY or Display Change button 
DISPLAY CHANGE if assigned as a Multi-purpose button 
Alphanumeric Speed Dial by Name 
The Alphanumeric Speed Dial By Name feature allows users to access the speed dial 
list alphabetically. When a user wants to place a outside line outgoing call with the 
Speed Dial...