JVC Rx330v Manual

							
1
ENGLISH
Continued on Next page
L When you have finished operationAlways follow the procedures below when disconnecting the camcorder, or turning off the power of the camcorder/PC.Failing to do so may cause damage to the camcorder and PC.
1)   Confirm that the access/charge lamp on 
the camcorder does not light or blink. (If the access/charge lamp lights or blinks, wait until it is turned off before proceeding.)
2)   Double-click the [Safely Remove 
Hardware] or [Unplug or Eject Hardware] icon in the status bar.
3)   Select [USB Mass Storage Device] or 
[USB Disk], and then click [Stop].
4)   Click [OK].
5)   Disconnect the USB cable.
6)    Turn off the camcorder and PC.
File Backup on the PC
This method uses the software on the provided CD-ROM to back up files onto your PC. Video files that have never been backed up onto the connected PC are automatically selected from the back up history and backed up. If you could not install the software, turn to 
page 52 for details of how to back up your files without using this software.
Preparation:• Install the software from the provided CD-ROM. (Z  pg.  49)• Connect the camcorder to the PC with the USB cable. (Z  left column)
NOTEWhen backup is performed, folders are created in the [MyWorks] folder (Z pg.  50), and the files are backed up inside those folders. 
Connecting the Camcorder to the PC
Preparation:Close the LCD monitor to turn off the camcorder.
NOTES
• Never disconnect the USB cable while the access/charge lamp on the camcorder lights or blinks.• Do not turn off the camcorder when the USB cable is connected, to prevent malfunctions of the PC.• Connect the camcorder directly to the USB jack on the PC, not through a hub.• Do not use an extension USB cable.• Saving the wrong kinds of files in an SD card or deleting files or folders from an SD card can cause problems with the operation of the camcorder. When it is necessary to delete a file from an SD card, delete it through the camcorder. Also, do not move or rename folders and files in the medium on PC.• It is recommended to use the AC Adapter as the power supply instead of the battery pack.
AC Adapter
DC Jack
USB Jack
To AC Outlet
USB Cable
USB Port 
						

							


1Open the LCD monitor to turn on the camcorder.
2On the camcorder, select [BACK UP].Although a dialog box appears on the PC, you do not need to use it.  PowerCinema starts automatically.
3Click [EVERIO_SD].
4Click [OK].
When the progress bar disappears, the process is complete.
File Backup on the PC without Using Software
Preparation:Connect the camcorder to the PC with the USB cable. (Z pg.  51)
1On the PC, create a folder to back up files into.
2Open the LCD monitor to turn on the camcorder.
3On the camcorder, select [PLAYBACK ON PC].A dialog box appears on the PC. 
4Select [Open folder to view files using Windows Explorer] and click [OK].
5Select the folder you want to back up, and drag & drop it into the folder you created in step 1.
• SD_VIDEO: Folder that contains video files. If you want to back up files individually, open this folder, and drag & drop files such as [PRG001] one by one.• DCIM: Folder that contains still image files. If you want to back up files individually, open this folder, and drag & drop files such as [PIC_0001.JPG] one by one.
NOTEFor further details on the use of folders, see 
page 59.
File Backup on a Windows® PC (Continued) 
						

							


ENGLISH

File Upload on a Windows ® PC
File Upload to YouTube
This method uses software on the provided CD-ROM to perform quick video clip upload to YouTube with a simple one touch operation.
This product’s YouTube upload functionality is included under license from YouTube LLC.  The presence of YouTube upload functionality in this product is not an endorsement or recommendation of the product by YouTube LLC.Preparation:• Install the software from the included CD-ROM. (Z pg. 49)• Connect the camcorder to the PC with the USB cable. (Z pg. 51)
1Open the LCD monitor to turn on the camcorder.
2On the camcorder, press the UPLOAD button.Although a dialog box appears on the PC, you do not need to use it. PowerCinema starts automatically.
3On the PC, click on the check box of the desired file.The s mark appears on the left of the selected file.To select other files, repeat this step.
4Click [YouTube].
5Login your username and password.  Click [Next].To create a YouTube account, click [Sign up to YouTube].
6Select video category and broadcast option. Click [Next].The Video Title is automatically filled in during uploading process with the File name, and the Description and Tags with Everio Video references. Date information is also input.If you want to modify this information, sign on to your account on the YouTube website: http://www.youtube.com/
7Click on the check box and then click [Upload].Uploading starts.Click [Cancel] to cancel procedure.
8Click [Finish].
NOTES
• It is recommended to use the AC Adapter as the power supply instead of the battery pack.• The operation is possible only with video clips that have been configured for this video sharing website. So, before you start shooting, set upload pre-record mode to “UPLOAD REC ON”. (Z pg. 24)• You can upload up to 10 movies under the same video category and broadcast option at one time.• It takes approx. 5 minutes to upload every 1 minute recording of a video clip (for uplink speed of 1Mbps).• There is no guarantee that the operation will work in all environments or when there are changes in YouTube site in the future.• For more information on YouTube, visit YouTube website: http://www.youtube.com/
L  If you could not upload by using PowerCinema, upload the video clip at YouTube website.
  1)  Copy the video clip (extension “.MOD”) 
to a PC by performing the procedure in “File Backup on the PC” (Z pg. 51 – 52).
  2)  Go to YouTube site, http://www.youtube.com/
  3)  Login your YouTube account and follow 
the steps to upload. 
						

							

Playing Back Files on the PC
Preparation:• Install the software from the provided CD-ROM. (Z pg.  49)• Connect the camcorder to the PC with the USB cable. (Z pg.  51)
1Open the LCD monitor to turn on the camcorder.
2On the camcorder, select [PLAYBACK ON PC].
Although a dialog box appears on the PC, you do not need to use it. PowerCinema starts automatically.
3Click [Browse Videos] (for video playback) or [Browse Pictures] (for still image playback).
4Click the media that contains the desired files.
5Click the desired file.
If you click Sort by/Filter by/View by, searching options are displayed. Use them to search a file quickly.• Sort by: The order of files is rearranged according to item that you selected.• Filter by: Files are filtered according to the item that you selected.• View by: You can change the number of thumbnails on a screen.
For more information on detailed operations of the software, see the Tutorials (Z pg.  56) or CyberLink web site (Z pg.  49).
Other Windows® PC Operations 
						

							

ENGLISH
Continued on Next page
Creating a DVD-Video
Preparation:• Install the software from the included CD-ROM. (Z  pg.  49)• Connect the camcorder to the PC with the USB cable. (Z  pg.  51)• Open the LCD monitor to turn on the camcorder.
Copying Video Files that Have Never Been Copied
1On the camcorder, press the DIRECT DVD button.
Although a dialog box appears on the PC, you do not need to use it. PowerCinema starts automatically.
2On the PC, authoring and burning starts.
Click [Stop] to cancel the procedure.
3Click [OK].
Selecting Files for Backup
1On the camcorder, select [CREATE DVD].
Although a dialog box appears on the PC, you do not need to use it. PowerCinema starts automatically.
2On the PC, click the check box of the desired file.
The s mark appears on the left of the selected file.To select other files, repeat this step.
3Click [Next].
4Click [Burn to Disc].
Authoring and burning starts.Click [Stop] to cancel the procedure.
5Click [OK]. 
						

							


For more information on detailed operations of the software, see the Tutorials (Z right column) or CyberLink web site (Z pg.  49).
NOTES
• It is recommended to use the AC Adapter as the power supply instead of the battery pack.• You can use following discs:
  -  DVD-R/DVD+R (Unused discs), 
DVD-RDL/+RDL
  -  DVD-RW/DVD+RW (They need to be 
formatted before recording. Formatting deletes all content recorded on the disc.)• DVD-RAM discs cannot be used.• You may not be able to play back the created disc depending on the performance of the device. Also, the image may stop momentarily at junctions between scenes.• The PC must be equipped with a compatible drive and player software to play back the created disc.
Getting More Use of the Software
For more information on operations of the software, see the Tutorials for each software program or the User’s Guides.
PowerCinema NE for Everio
1Double-click the PowerCinema NE for Everio icon.Start PowerCinema NE for Everio.
2Click [Help].
Digital Photo Navigator 1.5
The User’s Guide is included on the CD-ROM in PDF format.
1Load the provided CD-ROM into the PC.
2Right-click the CD-ROM icon in [My Computer], then click [Open].
3Double-click the [DOCS] folder.
4Open the “Start.pdf” file and click the button of the desired language.
NOTES
• You need to connect to the Internet to see the Tutorial.• Adobe® Acrobat® ReaderTM or Adobe® Reader® must be installed to read PDF files. Adobe® Reader® can be loaded from Adobe’s web site: http://www.adobe.com/
Other Windows® PC Operations (Continued) 
						

							


ENGLISH
You can back up camcorder files onto your computer.
System Requirements
Hardware:Macintosh must be standard equipped with USB 2.0 portOS:Mac OS X (v10.3.9, v10.4.2 to v10.4.11, v10.5.1 to v10.5.2)
Connecting the Camcorder to the Macintosh
Preparation:Close the LCD monitor to turn off the camcorder.
NOTES
• Never disconnect the USB cable while the access/charge lamp on the camcorder lights or blinks.• Do not turn off the camcorder when the USB cable is connected, to prevent malfunctions of the PC.• Connect the camcorder directly to the computer, not through a hub.
• Do not use an extension USB cable.• When you copy files from the computer to the SD card on the camcorder, do not include any other files than those recorded with the camcorder.• Do not delete, move, or rename the files and folders in the camcorder from the computer.• It is recommended to use the AC Adapter as the power supply instead of the battery pack.
L When you have finished operationAlways follow the procedures below when disconnecting the camcorder, or turning the power of the camcorder/computer off.Failing to do so may cause damage to the camcorder and computer.
1)   Drag & drop the SD card icon on the 
desktop into the [Trash] icon. If the confirmation message appears, click [OK].
2)   Confirm that the access/charge lamp on 
the camcorder does not light or blink. If the access/charge lamp lights or blinks, wait until it is turned off before proceeding.
3)   Disconnect the USB cable.
4)    Turn off the camcorder and computer.
File Backup on a Macintosh® 
DC Jack
USB Jack
AC Adapter
To AC Outlet
USB Cable
USB Port 
						

							


• DCIM: Folder that contains still image files. If you want to back up files individually, open this folder, and drag & drop files such as [PIC_0001.JPG] one by one.
NOTEFor further details on the use of folders, see page 59.
File Backup on the Macintosh
Preparation:Connect the camcorder to the computer with the USB cable. (Z pg. 57)
1On the computer, create a folder to back up files into.
2Open the LCD monitor to turn on the camcorder.
3On the camcorder, select [PLAYBACK ON PC].
4Double-click [EVERIO_SD] icon.
Depending on the type of OS used, iPhoto starts if the SD card contains a DCIM folder.
5Select the folder you want to back up, and drag & drop it into the folder you created in step 1.
• SD_VIDEO: Folder that contains video files. If you want to back up files individually, open this folder, and drag & drop files such as [PRG001] one by one.
File Backup on a Macintosh® (Continued) 
						

							


ENGLISH

[XXXJVCSO][XXXJVCSO][XXXJVCSO]
[DCIM]
[SD_VIDEO]
[EXTMOV]
[MISC]
[PRIVATE]
[MGR_INFO]
[PRGXXX]
[PRGXXX][PRGXXX]
[PRGXXX.PGI][MOVXXX.MOD][MOVXXX.MOI]
[MOV_XXX.MOD]

* Information such as the date and time of recording, recorded with the video f\
ile.
Extensions
Video files:“.MOD”Still image files:“.jpg”
For Windows®, the file extension may not appear depending on the [FOLDER] option setting.
Recording mediumX = number
Folder Structure and Extensions
Management information*
Contains the video file folders.
Contains the still image folders.
Management information* for the media as a whole
Video file
Management information* for the video files
Contains management information files of event and/or DVD creation information for the files taken with the camcorder.
Contains folders with DPOF setting data.
Video file which management information is corrupted. 
						

							
0
Contact us for Information on the Provided Software
Use of this software is authorized according to the terms of the software licence.
JVC
When contacting the nearest JVC office or agency in your country (refer to the JVC Worldwide Service Network at http://www.jvc-victor.co.jp/english/worldmap/index-e.html) about this software, please have the following information ready.
• Product Name• Model• Problem• Error Message
• PC
  Manufacturer
  Model (Desktop/Laptop)
  CPU
  OS
  Memory (MB)
  Available Hard Disk Space (GB)
Please note that it may take some time to respond to your questions, depending on their subject matter.JVC cannot answer questions regarding basic operation of your PC, or questions regarding specifications or performance of the OS, other applications or drivers.
CyberLink
Telephone/fax support
LocationLanguageOffice hours
(Mon.  to Fri.)Phone #Fax #
Germany English / German / 
French / Spanish / Italian
9:00 am to 5:00 pm+49-700-462-92375+49-241-70525-25
TaiwanMandarin9:00 am to 6:00 pm+886-2-8667-1298 ext. 333+886-2-8667-1300
JapanJapanese10:00 am to 5:00 pm+81-3-3516-9555–
Paid voice support
LocationLanguageLines are open
(Mon.  to Fri.)URL
U.S.A.English1:00 pm to 10:00 pm CSThttp://www.cyberlink.com/english/cs/support/new_site/voice_support.jsp
Support web/e-mail
LanguageURL/e-mail address
Englishhttp://www.cyberlink.com/english/cs/support/new_site/support_index.html
German / French /  Spanish / Italian
[email protected]
Japanesehttp://jp.cyberlink.com/support/
Customer Support Information