Keurig 2o Manual

3-4CUPS1
19
SECTION 1
BREW YOUR FIRST K-CARAFETM POD
1. Make sure the KeurigTM Carafe is empty. 
Remove the Drip Tray and insert the 
Keurig
TM Carafe securely in its place.  NOTE: Do not remove the foil lid or puncture the  
K-CarafeTM pod.
NOTE: Refer to page 29 for KeurigTM Carafe operation.
3. Select a Brew Size.NOTE: Make sure the number on the Touch Display matches 
the number of the K-CarafeTM pod you’re brewing in the  
pod holder.
2. Select a K-CarafeTM pod, place firmly in 
the Pod Holder and...

20 
Brewing
HOT: DO NOT LIFT!HOT: DO NOT LIFT!
Brewing
More WaterPlease.
STOPPING THE BREW PROCESS
ADDING WATER
FOR K-CUP® PODS AND K-CARAFETM PODS (KEURIG BREW™ SETTING 1)
To stop the brewing process, press and hold the Power Button for one second. 
Remove and dispose of any used pod. Brewing a used pod is not recommended.
Your Keurig
® 2.0 brewer will indicate when the water level in the Water Reservoir is low 
and you will not be able to brew. The brewer will only indicate “More Water Please.” if...

CONTINUE
CANCEL Dispenase
Hot Water?
H
Enjoy!
21
SECTION 2
DISPENSING HOT WATER INTO A MUG
1. Place a mug on the Drip Tray. Lift and 
lower the Handle without a pod. 2.
Press CONTINUE to dispense hot water.
3. Select your Brew Size and press the 
Brew Button. 4.
When the brew process is complete, 
the Touch Display will indicate Enjoy! 

22 
LANGUAGE
ESPAÑOL
FRANÇAIS
ENGLISHSETTINGSLANGUAGE
HIGH ALTITUDE
WATER FILTER REMINDER
SETTINGSLANGUAGE
HIGH ALTITUDE
WATER FILTER REMINDERLift to Begin
ACCESS SETTINGS
Explore everything your Keurig
® 2.0 
brewer has to offer by accessing the 
SETTINGS menu. From the home screen, 
select the Settings Button.
Use the arrows to scroll through the 
menu. To exit, press the back button.
Press the back button to return to the 
SETTINGS menu or press the HOME 
button to return to the home screen. 
Your...

23 
HIGH ALTITUDE
ENABLE
SETTINGSLANGUAGE
HIGH ALTITUDE
WATER FILTER REMINDER
WATER FILTER REMINDER
ENABLE
SETTINGSLANGUAGE
HIGH ALTITUDE
WATER FILTER REMINDER
SECTION 2
ENABLE WATER FILTER REMINDER
If you are using a Keurig
® Water Filter, 
select ENABLE to activate the WATER 
FILTER REMINDER notices.
Press the back button to return to the 
SETTINGS menu or press the HOME 
button to return to the home screen. 
Your settings will be automatically saved.
Refer to page 30 for more information. ENABLE HIGH...

24 
CLEANING THE BREWER EXTERIOR
Keep your Keurig
® 2.0 brewer looking its best by cleaning the exterior from time to time. 
Just clean with a damp, soapy, lint-free, non-abrasive cloth. Never immerse the brewer in 
water or other liquids. 
CLEANING THE DRIP TRAY
The Drip Tray can accumulate up to 8 ounces of overflow. The Drip Tray and the Drip Tray 
Plate should occasionally be rinsed clean. To remove the Drip Tray, simply slide it toward 
you, keeping it level at all times to avoid spilling. Clean...

25 
SECTION 2
CLEANING THE WATER RESERVOIR AND THE WATER RESERVOIR LID
Clean the Water Reservoir and the Water Reservoir Lid with a damp, soapy, lint-free,  
non-abrasive cloth and rinse thoroughly.  
Do not dry the inside of the Water Reservoir with a cloth as lint may remain. Be sure to 
rinse the Water Reservoir thoroughly after cleaning to ensure that no cleaning solutions 
remain as they may contaminate the water supply in the brewer.
DO NOT PLACE THESE ITEMS IN THE DISHWASHER. 

26
3.Pull out the Pod Holder Assembly (1) 
and Base (2).
CLEANING THE POD HOLDER
1.
Lift the Handle. 2.Push up while grabbing the sides of the 
Pod Holder Assembly. Pull away from 
the brewer.
CAUTION: Sharp needles. Do not put fingers in chamber.
4.Press the release buttons on both sides 
of the Pod Holder Assembly.
Separate the Pod Holder from 
the Housing.
CARING FOR YOUR BREWER 

27
5.Clean the P od Holder (1), Housing (2), 
and Base (3) with a damp, soapy, 
lint-free, non-abrasive cloth and 
rinse thoroughly.
SECTION 2 

28
CARING FOR YOUR BREWER
CLEANING THE EXIT NEEDLE 
1.If a clog arises in the Exit Needle, push 
the lever of the Pod Holder to reveal 
the Exit Needle. 
3. After all pieces are cleaned, place the 
Base then the Pod Holder Assembly 
into the Brew Head. Lower the 
Handle.
CAUTION: Sharp needles. Do not put fingers in chamber.
2.Use a paper clip or similar tool to 
loosen the clog. Rinse thoroughly with 
hot water.