Keurig B 30 Manual

							
USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new  
B30 MINI Keurig® Brewer
COMMENT UTILISER VOTRE CAFETIÈREMANUEL D’UTILISATION : Tirez le meilleur de  votre nouvelle cafetière MINI B30 de Keurig® 
						

							
3
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic  safety precautions should be followed,  
including the following:
1.  
Read all instructions before using.
2.  
Do not touch hot surfaces. Use handles and 
knobs when available.
3.  
This appliance must be properly installed and 
located in accordance with these instructions 
before it is used.
4.  
The use of accessory attachments not recom-
mended by the appliance manufacturer may re-
sult in fire, electrical shock or injury to persons.
5.  
Do not place on or near a hot gas or electric 
burner, or in a heated oven.
6. Do not use outdoors.
7.  
To protect against fire, electric shock and injury, 
do not immerse cords, plugs or the appliance in 
water or any other liquid.
8.  
Use only water in this appliance! Do not put any 
other liquids or foods in the Water Reservoir.
9. 
  
Unplug the coffee brewer when not in use and 
before cleaning.  Allow to cool before attach-
ing or removing parts and before cleaning the 
appliance.
10.  
Do not operate any appliance with a damaged 
cord or plug or after the appliance malfunc-
tions or is damaged in any manner. Contact 
your Keurig Customer Service to arrange for 
replacement or repair.
11.  
Do not let the cord hang over the edge 
of the table or counter, or touch hot surfaces.
12.  
To disconnect, turn the Power Button on the 
right-front of the Brewer off and then remove 
the plug from the wall outlet.
13.  
Close supervision is necessary when 
any appliance is used by or near children.
14.   
Do not push the PRESS TO OPEN Button
 
while brewing is in progress.
15.  
This appliance is equipped with a power 
cord having a grounding wire with a grounding 
plug. The appliance must be grounded using a 
3-hole, properly grounded outlet. In the event of 
an electrical short circuit, grounding reduces 
the risk of electrical shock.
16.   
If the outlet is a standard 2-prong wall 
outlet, it is your personal responsibility 
and obligation to have it replaced with a 
properly grounded 3-prong wall outlet.
17.  
Do not, under any circumstances, cut or 
remove the third (ground) prong from 
the power cord or use an adapter.
18.  
Consult a qualified electrician if the 
grounding instructions are not completely 
understood or if doubt exists as to whether 
the appliance is properly grounded.
19.  
Do not use the appliance for any reason  
other than its intended use.
Sav E Th ESE 
I NSTRU cTIONS .
CAUTION: There are two sharp needles that puncture the K-Cup® portion pack, one above the 
K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
CAUTION: There is extremely hot water in the  K-Cup Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup  Assembly Housing during the brewing process.
2 
						

							
3
Th IS PRODU cT IS FOR  cOMMER cIa L  aND  hOUSE hOLD USE  
To reduce the risk of injury, do not drape cord over the counter 
top or table top where it can be pulled on by children or tripped  
over unintentionally.
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING 
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, 
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
MINI  —  Model B30 
Using Your Brewer
SE cTION 1  —  SETUP & OPERATION 
Priming & First Brew  .........................................................................5
SE cTION 2  —  CLEANING & MAINTENANCE 
Cleaning  ................................................................................................8 
Storage  .................................................................................................9 
De-Scaling............................................................................................9
SE cTION 3  —  TROUBLESHOOTING..................................................10
SE cTION 4   —  WARRANTY ................................................................11
 Pour des directives en français, veuillez vous reporter à la page 17.
Record your Brewer Serial Number here.
WARNING
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.
Removing the serial number label from the Brewer will void warranty. 
RISK OF FIRE OR  ELECTRIC SHOCK  DO NOT OPEN! 
						

							
B30 MINI Keurig® Brewer

BREW
a
B
c
D
EF
G
I
J
a
B
c
D
E
F
G
h
J
Place Cup Indicator (Green)
Heating Indicator (Red)
BREW Button
Power Button
Drip Tray Plate
Drip Tray
Cup Sensors
PRESS TO OPEN and Insert K-Cup®
Funnel
h
I
K-Cup® Portion Pack Holder  (I and J are the K-Cup Holder Assembly)       
						

							

SECTION 1  Set-up & Operation
1.  
Plug Brewer into its own grounded 
outlet. If the electric circuit is over-
loaded with other appliances, your 
Brewer may not function properly. 
If possible, the Brewer should be 
operated on its own circuit, sepa-
rate from other appliances.
2.  Select a K-Cup® portion pack.  
Do not remove the foil lid or punc-
ture the K-Cup portion pack.
3.   Make sure the Brewer is plugged 
in. Press the Power Button found 
on the front of the Brewer.
4.  
Depress the large “PRESS  
TO OPEN” Button on top of  
the Brewer.
1234                       
						

							

5.  Place chosen K-Cup® into the  
K-Cup Assembly Housing. 
CAUTION: There are two sharp 
needles that puncture the K-Cup,  
one above the K-Cup Holder and 
the other in the bottom of the K-Cup 
Holder. To avoid risk of injury, do  
not put your fingers in the K-Cup  
Housing Assembly.6.   
Lower the Handle
 completely  
and firmly  to close the Lid 
 
and puncture the  K-Cup®  
portion pack. 
7.  
The Hot Water Tank cover will  
open automatically.
8.  
Fill the Hot Water Tank 
with filtered or bottled  
water up to the FILL 
LEVEL indicator.
5678
Setup & Operation (continued)SECTION 1                                                                 
						

							

9.  Close the Hot Water  
Tank cover. The  
“PL ACE CUP” light  
 will be flashing.
911121310
13. Enjoy!10.   Place a 10 oz coffee cup  
in the dispense area on  
the Drip Tray Plate. 
        NOTE: Do not use a clear,  glass mug. Cup  sensor will  not “read” the glass mug  and the “Place Mug” light  
will flash.
11.  
Press the flashing  
BREW Button. The  
HEATING light will  
be illuminated.
12.  When the water  
reaches temperature,  
(less than 3 minutes)  
the HEATING light 
will go off and the 
coffee/tea/hot cocoa 
will start to dispense.                                                                      
						

							



cleaning External Parts
IMPORTANT: Make sure the Brewer is unplugged before cleaning
Regular cleaning of the Brewer’s external components is recommended.
1.  Never immerse the Brewer in water or other liquids. The Housing  
and other external components may be cleaned with a soapy, damp,  
non-abrasive cloth.
2.   The Drip Tray can accumulate liquids. The Drip Tray and Drip Tray Plate 
should be periodically inspected and cleaned with a damp soapy non-
abrasive lint free cloth. The Drip Tray and Drip Tray Plate should not be 
put into the dishwasher. To remove the Drip Tray Assembly, simply slide  
it toward you, keeping it level at all times to avoid spilling.
c leaning the K- cup  holder  assembly
1.   
Cleaning the Parts  —The K-Cup Holder 
Assembly can be placed onto the top shelf of a 
dishwasher. NOTE: Use low temperature cycles 
in the dishwasher. To remove from the Brewer, 
open the cover by pressing the “Press to Open” 
button. Grasp the top of the K-Cup Holder with 
one hand while pushing up on the bottom of the 
K-Cup Holder from underneath with the other 
until it releases (fig. 1). After cleaning, align the 
K-Cup Holder with the opening using the two 
front ribs as a guide, and snap into place from 
the top. 
2.   
Cleaning the Funnel  —The Funnel can be 
removed from the K-Cup Holder by pulling  
on it until it snaps off (fig. 2). The Funnel is 
dishwasher safe. To replace it, just snap it  
back onto the K-Cup Holder Assembly.
3.  
Cleaning the Exit Needle  —The Exit Needle is 
located on the inside bottom of the K-Cup 
Holder Assembly. Should a clog arise due to 
coffee grinds, it can be cleaned using a paper 
clip or similar tool. Remove K-Cup Holder 
assembly and detach Funnel. Insert the paper 
clip (as shown in fig. 2) into the Needle to 
loosen the clog and push it out. The K-Cup 
Holder is dishwasher safe. NOTE: The Entrance 
needle does not require cleaning.
CAUTION: There are sharp needles that puncture the K-Cup above the K-Cup 
Holder and in the bottom of the K-Cup Holder. To avoid risk of injur y, do not 
put your fingers in the K-Cup A ssembly Housing.
NOTE: Over time, discoloration, spotting or staining may appear in the Hot 
Water Tank. This is normal and will vary depending on the mineral content of 
the bottled or filtered water used in the Brewer and will not affect the operation 
of the Brewer.
fig. 1
!
fig. 2
SECTION 2  Cleaning & Maintenance         
						

							



cleaning the  hot Water Tank
To access the Hot Water Tank, press the PRESS TO OPEN Button and then 
lower the handle completely, the water fill lid will pop open. Inspect the Hot 
Water Tank area and clean with a damp lint free cloth as necessary. Close 
the water fill lid when finished.
Emptying the  hot Water Tank
1.  
Ensure that the water fill lid is closed.
2.  
Place a cup on the drip plate then press and hold the BREW Button until all 
the water has been dispensed. Note, there will be a delay of   –   seconds 
until water starts to dispense.
Storage
Empty the Hot Water Tank before storing and take care to ensure that you 
store your Brewer in a safe and frost free environment. It is suggested to 
store your Brewer in the upright position. If you store the Brewer in a cold 
environment, you run the risk of condensation freezing inside the Brewer and 
causing damage. When you prepare to use it after storage, we recommend 
wiping the Hot Water Tank with a damp lint-free cloth and running three 
cleansing brews without a K-Cup.
If your Brewer has been in an environment below freezing, please be sure to 
let it warm to room temperature for 2 hours before using.
De-Scaling Your Brewer
Mineral content in bottled or filtered water varies. Depending on the mineral 
content of the water, calcium deposits or scale may build up in your Brewer. 
Scale is non-toxic but left unattended, it can hinder Brewer performance. De-
scaling your Brewer helps maintain the heating element, and other internal 
parts of the Brewer that come in contact with water.
The Brewer should be de-scaled every 3-  months to ensure optimal 
performance or when there are white deposits in the Hot Water Tank. It  
is possible for calcium deposits to build up faster, making it necessary to  
de-scale more often.
Step 1:  
Make sure you have at least   ounces of undiluted white vinegar on 
hand. You will also need a 10 oz ceramic cup (do not use a paper cup) 
and access to a sink.
Step 2:  
Fill Hot Water Tank with   ounces of undiluted white vinegar up to the 
FILL LEVEL mark, place a ceramic cup on the Drip Tray Plate.
Step 3:  
Close the lid, and perform a brew into the ceramic cup without adding 
a K-Cup. 
Step 4:  
Pour the contents of the ceramic cup into the Hot Water Tank, careful 
the liquid will be hot, close the lid. Start a brew but power off the 
Brewer just after it starts to dispense and then allow it to sit for at 
least 30 minutes.
Step 5:  
After the prescribed period of time, perform a brew without adding a 
K-Cup. Empty the contents of the ceramic cup into the sink, be careful 
as contents may be hot. 
						

							
SECTION 2De-Scaling Your Brewer (continued)
Step 6:  Fill the Hot Water Tank with   ounces of bottled water, close the water 
fill lid, place a cup on the Drip Tray Plate and perform a brew.
Step 7:  
Repeat Step   three times using bottled water (with no K-Cup in place) 
to cleanse the Brewer plumbing and get rid of any residual taste from 
the vinegar. The Brewer is now ready for normal use again.
Service
Beyond these recommended cleaning and maintenance procedures this 
Brewer is not user serviceable, for service please refer to the Warranty 
section in this guide.
SECTION 3  Toubleshooting
Situation 
Brewer does not have power
•   
Make sure the Power Button is pressed and is illuminated
• Plug Brewer into an independent outlet. • Check to be sure that it is plugged in securely.  • Plug into a different outlet.  • Reset your home’s circuit breaker if necessary.
Brewer will not brew when used for the first time
•   
If Brewer is cold/frozen, wait for at least two hours for it to reach room 
temperature before powering on.
Brewer will not brew
•   
Check to make sure there is water in the Hot Water Tank.
• Place a cup on the Drip Tray Plate.
•   Check to be sure you are not using a clear, glass mug. Cup sensor will not 
“read” the glass mug and the “Place Mug” light will flash.
Brewing a partial cup
• The Exit Needle may be clogged. (refer to page  ).
•   
Clean K-Cup Holder if necessary and rinse under faucet. (refer to page  ).
• De-scale the Brewer (refer to page  ).
•   
If you have repeated the de-scale procedure on your Brewer two times and the 
Brewer is still not brewing, contact Customer Service at 1. . 01.BREW 
(2 3).
My Brewer shuts off automatically
•   
Check to make sure that there is a cup on the Drip Tray Plate.
10