Kodak V600 Zoom Projector User Manual

							Checking the Status
17
English
Checking the Status
The information displayed on the Status tab depends on the type of 
image source you use.
The Reset Lamp Hours feature is the only item that can be adjusted 
on this screen. Refer to the Lamp Hours Used when you want to 
know how much longer your lamp will last. Estimated lamp life 
expectancy is 2,000 to 4,000 hours.
Important:Only reset the lamp hours after you have installed a new 
lamp.
To reset lamp hours
1. Press Menu and use the Adjust + - buttons to go to the Status tab.
2. Press Next to highlight Reset Lamp Hours.
3. Press Enter.
The Lamp Hours Used number resets to zero. 
Computer Source
Video Source
V600UserGuide.book  Page 17  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
18
Turning Off the Projector
Turn off the projector and image sources in the order listed here. 
Note: You might not be using all of these components for your 
presentation.
• Computer
•Projector
• Audio source if different from your video source or 
computer
• Video source such as VCR, DVD or digital camera. 
To turn off the projector:
1. Press the Power button on the keypad or remote control. 
A confirmation screen appears. 
2. Press the Power button again to confirm.
The lamp turns off immediately but the fan continues to run until 
the projector cools down.
The Power light continues to blink after the projector has cooled 
and as long as the live power cord is connected to the projector. 
V600UserGuide.book  Page 18  Tuesday, March 21, 2000  8:26 AM 
						

							Transporting the Projector
19
English
Transporting the Projector
When you place the projector in the carrying case make sure the lens 
is positioned inside the lens notch of the foam insert. Secure the 
projector with the velcro strap.
Important:The carrying case provided with the projector is not 
designed to be checked through baggage. If you can not 
hand carry this projector make sure it is packed properly to 
prevent damage. The warranty does not cover damage 
from improper handling.
A hard-sided case is available as an option. To purchase accessories, 
go to our Web site at www.kodak.com/go/projectors.
lens notch
foam insert
velcro strap
velcro strap
V600UserGuide.book  Page 19  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
20
Maintenance
Changing the Lamp Module
Important:The lamp in the KODAK V600 Digital Projector and the 
KODAK V600 Zoom Digital Projector contains trace 
amounts of mercury. Some governments require special 
disposal of lamps containing mercury. Dispose of lamps in 
accordance with the law and any applicable local 
regulations.
The lamp module should be replaced with a certified replacement 
part. To order a new lamp, contact your local dealer of KODAK 
products or visit our Web site at www.kodak.com/go/projectors 
After you have changed the lamp module, make sure that you reset 
the lamp counter. See “To reset lamp hours” on page 17.
Wa r n i n g : When replacing the lamp, be sure to turn off the power and 
unplug the power cord. To avoid burns, wait 30 minutes before 
opening the lamp module door.
Wa r n i n g: When you open the lamp module door, be careful to not 
touch the hot surfaces inside.
Wa r n i n g: Do not loosen or remove any screws other than those on 
the lamp module door and the lamp module. Doing so may result in 
electric shock.
To replace the lamp module:
1. Turn off the projector and let the projector cool for at least 30 
minutes.
The fan continues to run after the projector has been turned off.
2. Unplug the power cord from the projector.
3. Turn the projector upside down. With a flat head screw driver, 
loosen but do not remove the slotted screw in the lamp module 
door. 
V600UserGuide.book  Page 20  Tuesday, March 21, 2000  8:26 AM 
						

							Maintenance
21
English
4. Lift up on the screw side of the lamp module door. Then 
carefully remove the lamp module cover.
5. Loosen the two slotted screws on the lamp module bracket.      
6. Gently lift and pull up on the metal wire to remove the lamp 
module.
&DXWLRQ RQRWWRXFKWKHJODVVSRUWLRQRIWKHQHZODPSPRGXOH
ZLWK\RXUKDQGVRUDOORZLWWRWRXFKRWKHUREMHFWVDVWKLV
PD\GDPDJHLWDQGVKRUWHQLWVRSHUDWLRQDOOLIH
&DXWLRQ RQRWGURSWKHODPSPRGXOHDVWKHJODVVPD\VKDWWHU
DQGFDXVHLQMXU\
V600UserGuide.book  Page 21  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
22
7. Carefully place the new lamp module into the projector, with the 
glass portion facing left. Make sure that it is inserted securely and 
that the two holes match the two pins of the inner engine case. 
Tighten the slotted screws.
8. Replace the lamp module door and tighten the screw.
9.Reset the lamp usage counter. See “To reset lamp hours” on 
page 17.
Important:The only time that you should reset the counter is after you 
have replaced the lamp module.
Cleaning the Projection Lens
1. Turn off the projector and allow it to cool. 
2. Remove the lens cap.
3. Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
&DXWLRQ $YRLGXVLQJDQH[FHVVLYHDPRXQWRIFDPHUDOHQVFOHDQHU
RQRWXVHDEUDVLYHFOHDQHUVVROYHQWVRURWKHUKDUVK
FKHPLFDOVDVWKH\PLJKWVFUDWFKWKHOHQVRQRWVSLOO
DQ\FDPHUDOHQVFOHDQHURQWKHH[WHULRUFDVHDVLWPD\
IDGHGHIRU PRUPHOWWKHH[WHULRUFDVH
4. Lightly wipe the cleaning cloth over the lens.
5. If you do not intend to use the projector immediately, replace the 
lens cap.
Cleaning the Exterior Case
1. Turn off the projector and allow it to cool.
2. To remove dirt or dust, gently wipe the exterior case with a soft, 
dry, lint-free cloth.
3. To remove stubborn dirt or stains, moisten a soft cloth with water 
and a neutral detergent and gently wipe the exterior case.
&DXWLRQ RQRWXVHDOFRKROEHQ]HQHWKLQQHURURWKHUFKHPLFDO
FOHDQHUVZKLFKPD\IDGHGHIRUPRUPHOWWKHH[WHULRU
FDVHRQRWDSSO\WKHGHWHUJHQWVROXWLRQWRWKH
SURMHFWRUOHQVDVLWPD\VFUDWFKWKHOHQV
V600UserGuide.book  Page 22  Tuesday, March 21, 2000  8:26 AM 
						

							Maintenance
23
English
Cleaning the Air Filter
To ensure proper ventilation inside your multimedia projector, the air 
filter should be periodically cleaned. More frequent cleaning may be 
required if you use your projector in a dusty or dirty environment.
&DXWLRQ ,IWKHDLUILOWHULVQRWFOHDQHGSHULRGLFDOO\LWFDQEHFRPH
FORJJHGZLWKGXVWDQGSUHYHQWSURSHUYHQWLODWLRQ7KLV
PD\FDXVHRYHUKHDWLQJDQGGDPDJH
Important:If the filter cannot be cleaned or becomes damaged or 
torn, it should be promptly replaced with an certified 
KODAK replacement part. Contact your dealer of KODAK 
products for additional information or visit our Web site at 
www.kodak.com/go/projectors
1. Turn off the projector and wait for the fan to stop running.
2. Unplug the projector. 
3. Turn the projector on its side so that the connection panel is 
facing upwards. 
Note: Standing the projector on its side keeps dust from getting 
inside.
4. Locate the air filter cover on the bottom of the projector and slide 
the cover latch downward to remove the cover.
The air filter is attached to the inside of the air filter cover.
5. Use a soft brush to clean the air filter being careful not to tear the 
filter or loosen it.
&DXWLRQ ,QVWDOOLQJDZHWRUGDPSDLUILOWHUPD\GDPDJH\RXU
SURMHFWRU
6. Replace the air filter cover on the projector. Make sure that it 
clicks into place.
&DXWLRQ 1HYHUUHSODFHWKHDLUILOWHUFRYHUZLWKRXWWKHDLUILOWHU
DWWDFKHGWKLVDOORZVGXVWWRJHWLQVLGH1HYHURSHUDWH
\RXUSURMHFWRUZLWKRXWWKHDLUILOWHUFRYHULQSODFH
RLQJVRPD\GDPDJH\RXUSURMHFWRU
V600UserGuide.book  Page 23  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
24
Tr o u b l e s h o o t i n g
If you don’t find the answer to your problem here, visit our Web site 
at www.kodak.com/go/projectors 
for the latest updates on 
troubleshooting.
Power Indicator
The power indicator on the keypad provides you with information 
about the condition of the projector. 
Light Status Condition
Blinking Lamp is off but live power cord is 
connected to the projector. 
Projector is in standby mode.
OR
Lamp is off and fan is running. 
Projector is cooling down.
Steady  Lamp is on and fan is running. 
Projector is ready.
Two blinks Scaling chip is malfunctioning. 
Call 
KIC-D at 800-23kodak.
Three blinks RAM is malfunctioning. 
Call 
KIC-D at 800-23kodak.
Four blinks I2C bus is malfunctioning. 
Call 
KIC-D at 800-23kodak.
Five blinks Lamp is malfunctioning. 
Call 
KIC-D at 800-23kodak.
Six blinks Fan is malfunctioning. 
Call 
KIC-D at 800-23kodak.
V600UserGuide.book  Page 24  Tuesday, March 21, 2000  8:26 AM 
						

							Troubleshooting
25
English
Image Quality
Problem Solution 
Color or text is not being 
projected.Adjust the brightness up or down until 
the text is visible.
Some text or fonts are not 
sharp with a computer as an 
image source.For optimal results, set the computer’s 
resolution to 800 x 600. (Refer to your 
computer user manual.) But this projector 
can compress resolutions up to 
1024 x 768.
Image isnt centered on the 
screen. • Be sure that the projector is at a 90° 
angle to the screen.
• Reposition the image. See “Setting Up 
the Image Source” on page 14.
Image is out of focus. • Turn the projection lens to focus the 
image.
• Make sure that the projection screen is 
at least 3 ft (.9 m) from the projector.
• Check the projection lens to see if it 
needs cleaning.
Image and menus are upside 
down.• If projecting from a ceiling mount, 
make sure that Ceiling Projection is 
selected on the Setup tab in the Menu.
• If projecting from an upright position, 
make sure that Front or Rear projection 
is selected on the Setup tab in the 
Menu. 
Image and menus are 
reversed from left to right.• If projecting from behind a screen 
make sure that Rear Projection is 
selected on the Setup tab in the Menu.
• If projecting in front of a screen, make 
sure that Front or Ceiling Projection is 
selected on the Setup tab in the Menu. 
V600UserGuide.book  Page 25  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
26
Image appears flat with no 
contrastTo adjust the contrast:
1. Press Menu and use the Adjust + -
buttons to go to the Adjust tab.
2. Use the Next button to highlight 
Contrast.
3. Use the Adjust + - buttons to 
increase or decrease the contrast.
Image appears washed out or 
dark.• Check the projection lens to see if it 
needs cleaning. 
• To adjust the brightness:
1. Press Menu and use the Adjust + -
buttons to go to the Adjust tab.
2. Use the Next button to highlight 
Brightness.
3. Use the Adjust + - buttons to 
increase or decrease the brightness.
Image is noisy or streaked. • From the Setup tab in the menus, adjust 
the frequency and tracking manually to 
find an optimal setting.
• Try connecting to another computer. 
The problem could be with your 
computers video card.
Image is wider at the top or 
bottom of the screen. This keystoning effect is caused by the 
projection angle not being perpendicular 
to the screen. For a more pleasing image 
result, raise or lower the front legs or 
prop up the back of the projector. 
Image is wider at one side 
than the otherMake sure the projector is at a 90 degree 
angle to the screen.
Problem Solution 
V600UserGuide.book  Page 26  Tuesday, March 21, 2000  8:26 AM