Kodak V600 Zoom Projector User Manual

							Troubleshooting
27
English
Projected colors dont match 
the computer or video source 
colors.Use the KODAK Image Manager to 
select a setting that is more acceptable.
Important: The KODAK Image Manager 
settings work best if you select 
Reset from the Adjust Tab each 
time before selecting an Image 
Manager setting.
If further adjustment is needed, optimize 
the brightness, tint, color and contrast 
from the Adjust tab in the Menus. 
Problem Solution 
V600UserGuide.book  Page 27  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
28
Sound
Remote Control
Problem Cause and Solution
No sound.• Adjust volume.
• Verify audio / input connections.
• Adjust audio source.
Poor sound quality. • Make sure you are connected to the 
earphone jack on your laptop or line out 
jack on your desktop. 
• Make sure the volume setting on your 
computer is halfway.
No audio-out port on the 
image source.You are not able to connect audio to the 
projector.
Problem Cause and Solution
Projector responds poorly 
or not at all to the remote 
control.• Make sure that the total distance from 
the remote to the projector is no more 
than 32 feet (10 m).
• Point the remote control at the screen or 
at the front of the projector.
• Make sure nothing is blocking the 
infrared sensor on the front of the 
projector. 
• Darken the room. The lighting might be 
effecting the remote control. 
• Replace the remote control batteries.
V600UserGuide.book  Page 28  Tuesday, March 21, 2000  8:26 AM 
						

							Troubleshooting
29
English
Lamp
Problem Cause and Solution
No light is coming from the 
lamp.
                                             • Make sure that the power cord is 
properly connected to a fully functional 
AC electric outlet. The Power light 
blinks when the power is connected but 
the projector is not turned on. The 
Power light is a steady green when the 
lamp is running. 
• Make sure that the power cord is 
properly connected to the projector.
• Make sure that you have removed the 
lens cap on the projector lens at the front 
of the projector.
• Make sure you have pressed the Power 
button and the Power light is a steady 
green.
• Check the projectors lamp to make sure 
that it is securely connected in the lamp 
module.
• Make sure that the lamp module door is 
fully closed. 
• Make sure that the cable connectors do 
not have any bent pins.
• Replace the lamp.
Lamp shuts off. • A minor power surge may cause the 
lamp to shut off. Press the Power button 
twice to turn off the projector. (The 
Power light continues to blink and the 
fan continues to run until the projector 
cools down.) Wait at least three minutes, 
then press the Power button again.
• Replace the lamp module.
V600UserGuide.book  Page 29  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
30
Image Source
Problem Cause and Solution
The S-Video image source 
does not appear.Some inexpensive cables are not 
compatible with the projector. Be sure to 
use the cable that came with your 
projector.
Only the start-up screen 
appears and not the image 
from the image source. • Verify that the cables are connected 
correctly. See “Connecting the 
Projector” on page 6.
• Verify that the proper image source is 
connected and that it is selected on the 
Setup tab of the menus.
• Make sure that the image source is 
turned on.
• Turn off everything and power up again 
in the proper order. See “Turning Off the 
Projector” on page 18. See “Starting the 
Presentation” on page 7.
• Make sure that your laptops external 
video port is turned on. See the 
computer manual for details.
V600UserGuide.book  Page 30  Tuesday, March 21, 2000  8:26 AM 
						

							Troubleshooting
31
English
The image source is 
connected but a No Signal 
message appears.• Verify that the cables are connected 
correctly. See “Connecting the 
Projector” on page 6.
• Verify that the proper image source is 
connected and that it is selected on the 
Setup tab of the menus.
• Make sure there are no bent pins in the 
connectors.
• Make sure the image source is turned 
on.
• Turn off everything and power up again 
in the proper order. See “Turning Off the 
Projector” on page 18. See “Starting the 
Presentation” on page 7.
• Make sure that your laptops external 
video port is turned on. See the 
computer manual for details.
MFG Mode screen appears 
instead of the image.Turn off the projector and wait until the 
fan stops. Turn on the projector.
Note: The MFG mode screen appears if 
you press the Power button at the 
same time that you plug in the power 
cord. This mode should only be used 
by service technicians. 
Problem Cause and Solution
V600UserGuide.book  Page 31  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
32
Safety
These safety precautions include information to prevent personal 
injury and damage to the projector. 
Safety Definitions
Wa r n i n g : Statements identify conditions or practices that could 
result in personal injury.
Caution:
 Statements identify conditions or practices that could result 
in damage to your equipment.
Warni ng: For information about use of a feature, please refer 
to this User Guide.
Warni ng: Hot surface. Do not touch.
Projector Safety 
Wa r n i n g : To replace the lamp, turn off the power and unplug 
the power cord. To avoid burns, wait 30 minutes before opening 
the lamp door. Follow all instructions provided in this User 
Guide. See “Changing the Lamp Module” on page 20.
Wa r n i n g: When you open the lamp module door, be careful not 
to touch the hot surfaces inside.
Wa r n i n g : Please use the power cord provided. Connect the power 
cord to a receptacle with a protective safety (earth) ground terminal.
Wa r n i n g : Don’t look directly into the lens when the lamp is on. 
Doing so may cause eye injury.
Wa r n i n g :
 Servicing your own projector may expose you to hazards 
or create potential hazards. Also, servicing your own projector will 
void the warranty. Refer all service to qualified service personnel. See 
“If You Need Assistance” on page 2.
Wa r n i n g: In the unlikely event of the bulb rupturing, thoroughly 
clean the area behind the projector and discard any food that might 
have been contaminated with broken glass.
Wa r n i n g: Do not loosen or remove any screws other than those on 
the lamp module door and the lamp module. Doing so may result in 
electric shock.
Caution: Don’t set liquids on the projector. Spilled liquids may 
damage your projector.
Caution:
 Don’t put the projector on a hot surface or in direct sunlight.
Caution: Do not drop the projector. 
V600UserGuide.book  Page 32  Tuesday, March 21, 2000  8:26 AM 
						

							Safety
33
English
Caution: Never operate your projector without the lamp module or 
lamp module door. Doing so may damage the projector.
Caution: Proper ventilation is important. Don’t block ventilation 
openings. Never operate this projector in an enclosed area. Do not 
place the projector on a tablecloth or other soft covering that may 
block the vents. With ceiling installations, use approved mounting 
hardware. Do not put the projector near heat ducts, air cleaners, 
transformers or other electrical devices. For permanent installations 
follow local codes.
Caution: Do not touch the glass portion of the new lamp module 
with your hands or allow it to touch other objects as this may damage 
it and shorten its operational life.
Caution: Do not drop the lamp module as the glass may shatter. 
Battery Safety
• Read and follow all warnings and instructions supplied by 
the battery manufacturer.
• Keep batteries away from children.
• Store batteries in their original packaging.
• When inserting batteries, verify that the (+) and (-) terminals 
are aligned correctly.
• Replace all batteries of a set at the same time.
• Do not mix new batteries with used ones.
• Do not use batteries of different chemistries, capacities, 
brands or sizes together. Leakage could result.
• Do not disassemble, recharge, or short-circuit batteries.
• Do not subject batteries to high temperature or fire.
• Discard used batteries according to all applicable local and 
national regulations. 
• In the unlikely event of contact with battery electrolyte, 
customers in the U.S. can contact the Kodak Information 
Center (KIC) at 1-800-242-2424. U.S. customers can also 
contact KIC for information regarding electrolyte removal 
from KODAK product components. Customers outside the 
U.S. can contact their local Kodak Customer Service 
representative.
V600UserGuide.book  Page 33  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
34
Specifications
Specification V600 V600 Zoom
Weight in lbs. (kg) 7.5 (3.4) 7.6 (3.4)
Dimensions (inches) 
(WxDxH)12.8 x 9.8 x 3.6 
(with lens)12.8 x 10.8 x 3.6
(with lens)
Dimensions (mm) 
(WxDxH)325 x 250 x 92 
(with lens)325 x 275 x 92 
(with lens)
Color Palette 16.7 million (24 bit) 16.7 million (24 bit)
Resolution 800 x 600 800 x 600
XGA compression 
(1024 x 768)Ye s Ye s
Three 0.9” panel 
polysilicone LCDYe s Ye s
Projection lamp 120w UHP, ultra 
compact120w UHP, ultra 
compact
Lamp life Up to 4000 hours Up to 4000 hours
User-replaceable lamp Yes Yes
Brightness (ANSI lumens -
based on industry 
specification practices)800 800
Contrast ratio 
(Full On/Off)200:1 200:1 
V600UserGuide.book  Page 34  Tuesday, March 21, 2000  8:26 AM 
						

							Specifications
35
English
Projection Distances/
Image Sizes0.9 m (2.95 ft)
0.57 m (1.875 ft)
3.66 m (12 ft)
2.29 m (7.5 ft)
10 m (32.8 ft)
6.35 m (20.6 ft)0.9 m (2.95 ft)
0.4 m (1.33 ft) to 0.53 m 
(1.74 ft)
3.66 m (12 ft)
1.68 m (5.5 ft) to 2.19 m 
(7.17 ft)
10 m (32.8 ft)
4.67 m (15.3ft) to 6.1 m 
(20 ft)
Projection Lens Fixed/manual focus Manual zoom/focus
Zoom Factor N/A 1.3x
Keystone Correction 10 degrees 10 degrees
Aspect Ratio 4:3, 16:9 4:3, 16:9
Audio (built in) Stereo, 2 x 2 watts Stereo, 2 x 2 watts
Video Compatibility – 
NTSC/NTSC 4.43
PAL   B/D/G/H/I/K/L/N/M
SECAM   B/D/G/H/K/LYe s  Ye s  
Computer compatibility VGA/SVGA/XGA/
SXGAVGA/SVGA/XGA/
SXGA
Vertical frequency (Hz) 56 – 85 56 – 85
Horizontal frequency 
(KHz)30 – 90 30 – 90
MACINTOSH 
CompatibilityYe s Ye s
Audible noise – typical 42 measured 42 measured
Specification V600 V600 Zoom
V600UserGuide.book  Page 35  Tuesday, March 21, 2000  8:26 AM 
						

							KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector 
36
Connections on projector
Analog RGB (15 Pin HD)
Ye s Ye s
Composite video (RCA) Yes Yes
Stereo Audio (1/8” mini-
plug)Ye s Ye s
S-video Yes Yes
Power Supply
Voltage (AC RMS) 100 - 240  100 - 240
Frequency (Hz) 50 – 60 50 – 60
Auto Sense Yes Yes
Typical Power 
Consumption (watts)195 195
Operating Temperature 
Range0 – 35 degrees C 0 – 35 degrees C
Storage Temperature 
Range-20 – 70 degrees C -20 – 70 degrees C
Humidity Range (relative) 10 – 95% 10 – 95%
Altitude (operating) 0 – 10,000 ft
0 – 3,048 m0 – 10,000 ft
0 – 3,048 m
Altitude (storage) 0 – 40,000 ft.
0 – 12,192 m0 – 40,000 ft
0 – 12,192 m
Specification V600 V600 Zoom
V600UserGuide.book  Page 36  Tuesday, March 21, 2000  8:26 AM