Kyocera KM 2550 User Manual

							Basic Operation 
BASIC OPERATION GUIDE3-21
5To start printing, click [OK].
NOTE: For information on how to use the printer driver software, refer to 
the KX Printer Driver Operation Guide.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Operation 
3-22BASIC OPERATION GUIDE
Downloaded From ManualsPrinter.com Manuals 
						

							BASIC OPERATION GUIDE4-1
4 Optional Equipment
The following optional equipment is available for use with your 
machine
• Optional Equipment Overview ...................................... 4-2
• Document Processor .................................................... 4-3
• Paper Feeder ............................................................... 4-7
• Duplex Unit ................................................................... 4-8
• Finisher......................................................................... 4-8
• Job Separator ............................................................. 4-12
• Key Counter ............................................................... 4-13
• Fax Kit ........................................................................ 4-14
• Network Scanner Kit................................................... 4-14
• Memory Card (CompactFlash) ................................... 4-14
• Hard Disk.................................................................... 4-15
• Expansion Memory..................................................... 4-15
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
4-2BASIC OPERATION GUIDE
Optional Equipment Overview 
The following optional equipment is available for use with your machine.
Document Processor
page 4-3Expansion Memory
page 4-15
Fax Kit
page 4-14
Network Scanner Kit
page 4-14 Duplex Unit
page 4-8
Finisher
page 4-8
Job Separator
page 4-12Paper Feeder page 4-7Memory Card (CompactFlash) 
page 4-14 Hard Disk
page 4-15
Key Counter
page 4-13
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
BASIC OPERATION GUIDE4-3
Document Processor
Automatically feeds and scans 
multiple originals one by one.
Two-sided originals are 
automatically turned to enable 
both sides to be scanned.
Acceptable Originals
• Use sheet originals only
• Paper weight:
- One-sided originals: 45 to 160 g/m²
- Two-sided originals: 50 to 120 g/m²
• Paper sizes: A3 to A5R, Folio, 11 × 17 (Ledger) to 5
1/2×81/2 
(Statement).
• Maximum capacity: 50 sheets (50 to 80 g/m²) at one time. 30 sheets 
for Auto Selection mode.
Notes on Acceptable Documents
Do not use the following originals in the Document Processor. In addition, 
originals with punched holes or perforations should be loaded with the hole 
punched or perforated edge facing away from the direction of insertion into 
the Document Processor.
• OHP and other transparency films.
• Soft originals, for example carbon or vinyl paper, or other originals that 
are curled, wrinkled or creased.
• Irregularly shaped originals, wet originals, or originals that contain 
adhesive tape or glue.
• Originals bound with clips or staples. If using these originals, to avoid 
jams remove the clips or staples and straighten any curls, wrinkles or 
creases, before loading in the Document Processor.
• Originals with cut-out sections or that have a slippery surface on either 
side.
• Originals on which any correction fluid is still wet.
• Originals with strong folds. If using these originals, smooth out the 
folds before loading in the Document Processor. Failure to do so may 
result in the originals becoming jammed.
• Curled originals. If using these originals, smooth out the curled 
portions before loading them in the Document Processor.
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
4-4BASIC OPERATION GUIDE
Names of Parts
1Original Table — Place 
originals to be copied 
on this table.
2Original Insert Guides 
— Align these guides to 
fit the width of the 
originals to be copied.
3Left Cover — Open this 
cover if an original jam 
occurs.
4Original Eject Table — 
Originals that have 
been copied are ejected 
and stored here.
5Ejection Extension — Open this extension when using larger sized 
originals such as A3, B4, 11 × 17 (Ledger), and 8
1/2× 14 (Legal).
6Document Processor Release Grip — Hold this grip to open or 
close the Document Processor.
7Ejection Tray — Two-sided originals will be temporarily ejected 
here.
IMPORTANT: Ensure the Document Processor is closed whenever 
transporting the machine.
Placing Originals in the Document Processor
1Adjust the original insert guides to 
fit the width of the original(s).
IMPORTANT: To prevent jams, 
remove any originals remaining 
on the Original Eject Table and 
fan the originals to separate the 
sheets before loading them.
When setting multiple originals at 
one time, use originals of the 
same size. It is, possible to use 
different size originals of the same 
width (for example, 11 × 17 
(Ledger) and 11 × 8
1/2 or A4 and A3) at the same time in the auto 
selection mode. Refer to Chapter 1, Advanced Operation Guide.
32124 5
76
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
BASIC OPERATION GUIDE4-5
2Arrange the originals in order and 
place face up on the Original 
Table. Slide the leading edge of 
the originals into the Document 
Processor, as far as they will go.
IMPORTANT: To avoid jams, 
ensure originals do not exceed the 
level indicator on the inside of the 
rear insert guide.
3To ensure originals delivered to 
the Eject Table do not fall out, 
open the Ejection Extension when 
using larger sized originals such 
as A3, B4, 11 × 17 (Ledger), and 
8
1/2× 14 (Legal).
IMPORTANT: When copying 2-
sided originals, the originals are 
temporarily ejected onto the 
Ejection Tray in order to turn them over. Do not touch them at this point. 
Any attempt to remove them may cause the originals to jam.
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
4-6BASIC OPERATION GUIDE
Placing Originals on the Platen
When copying from an original 
which cannot be loaded in the 
Document Processor (for example 
books, magazines, objects, etc.), 
lift open the Document Processor 
and place the original directly on 
to the Platen.
NOTE: Ensure there are no originals left on the Document Processor 
before lifting it open. They may fall off when the Document Processor is 
opened.
Shadows may appear around the edges and up the middle of copies 
made from open-faced originals such as books.
IMPORTANT: Do not put undue pressure on the platen when closing the 
Document Processor
WARNING: Do not leave the Document Processor open as there is a 
danger of personal injury.
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
BASIC OPERATION GUIDE4-7
Paper Feeder
A Paper Feeder with additional 
cassettes can be added below the 
standard cassette(s).
• Cassette capacity: 300 sheets 
of standard paper (64 to 
105 g/m²).
• Paper sizes: A3, B4, A4, A4R, 
B5, B5R, A5R, Folio, 11 × 17 
(Ledger), 8
1/2× 14 (Legal), 
11 × 8
1/2, 81/2× 11 (Letter), 51/2×81/2 (Statement), and 81/
2
× 13 (Oficio II).
NOTE: Up to three cassettes can be added for the 16 ppm model, and up 
to two cassettes can be added for the 20 ppm and 25 ppm models.
The procedure for loading paper is the same as for the standard 
cassette(s). For further information refer to Loading Paper, on page 2-2.
The left covers are provided to allow paper to be removed when a paper 
jam occurs.
IMPORTANT: If the Paper Feeder is installed, always detach it before 
attempting to pick up or transport the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Optional Equipment 
4-8BASIC OPERATION GUIDE
Duplex Unit
Two-sided copies can be made if 
the duplex unit is installed. Two-
sided copies of sizes from A3 to 
A5R, Folio, 11 × 17 (Ledger) to 
5
1/2×81/2 (Statement) can be 
made.
Finisher
The Finisher holds a large quantity of copies and can sort multiple copy 
sets by offsetting each set. It can also staple collated copy sets.
The Finisher specifications are as follows:
Names of Parts
1Finisher Tray
2Process Tray
3Process Tray 
Extension
4Finisher Tray 
Extension
5Paper Output Guide 1
6Paper Output Guide 2
Tray Capacity and Paper Sizes
Non-stapling500 sheets (A4, 11 × 8
1/2, B5)
250 sheets (A3, B4, Folio, 11 × 17 (Ledger), 8
1/2×14 
(Legal), 8
1/2× 13 (Oficio II))
Stapling
(80 g/m² or less)For stapling 2 to 4 sheets: 130 sheets
For stapling 5 sheets +: 250 sheets
Stapling Capacity30 sheets (A4, 11 × 8
1/2, B5)
20 sheets (A3, B4, Folio, 11 × 17 (Ledger), 8
1/2×14 
(Legal), 8
1/2× 13 (Oficio II))
541 2 3
6
Downloaded From ManualsPrinter.com Manuals