Land Rover Audio Navigation System Nas Rover Manual

							Navigation operation
40
Confirm warning
Before you can use the navigation system, a 
warning appears.
If you confirm the receipt of this warning you 
state that you have read and understood the user 
guide and that you are aware of the dangers 
connected to the use of this navigation 
equipment.
Selecting navigation
Press the ‘Nav’ multifunctIon button. 
The main navigation menu appears after thIs 
dIsplay. 
NOTE: The navigation CD must be loaded when 
starting navIgatIon operation for the first time
If navIgation system has not yet been calibrated, 
a calibration journey is prompted.
A navigation CD with the data for the destination 
must be inserted to start the route calculation. 
During the calculation, the prompt CD flashes on 
the display. Once the calculation has been 
completed, the prompt CD extinguishes, the 
navigation CD can be removed and an audio CD 
can be inserted. 
When entering destinations, driving off should 
be delayed until the prompt CD disappears.
NAVIGATION SYSTEM
TPRadNavCD
ICE 1283
NAVIGATION SYSTEM
TPRadNavCD
ICE 0275 
						

							41
Navigation operation
Main navigation menu
Selection from:
DESTINATION
DEST. MEMORY
P. O. I.
LAST DESTINATIONS
can be made by turning the right rotary control 
and confirmed by pressing the right rotary 
control.
•DESTINATION
accesses the entry menu for the destination.
•DEST. MEMORY
contains destinations which have been stored 
previously
•P. O . I .
Menu for the selection of special local and 
inter-regional destinations and special 
destinations nearby. Special destinations are 
e.g. gas stations, airports, hospitals etc.
•LAST DESTINATIONS
A list of the last 50 destinations is displayed. 
The desired destination can be selected using 
the right rotary control. Before confirming 
with the right rotary control, details of the 
destination can be requested by pressing the 
left rotary control. Stopovers are not stored 
as last destinations.
ENTERING A DESTINATION
Select DESTINATION in the main navigation 
menu using the right rotary control and press to 
confirm.
The navigation data for the USA is stored on two 
CD’s (see Navigation CD’s).
When you need to enter a route from a place 
contained on the USA West CD (A) to a 
destination stored on the USA East CD (C), you 
will need to enter an intermediary destination (B) 
in one of the following states; North Dakota, 
South Dakota, Nebraska, Kansas, Oklahoma or 
Texas. Once you have reached the intermediary 
destination, or once you reach one of the 
aforementioned states, you may switch CD’s and 
enter your final destination (C).
NOTE: When switching CD’s, the vehicle should 
be stationary with the ignition turned on.
NAVIGATION SYSTEM
TPRadNavCD
ICE 0276
ICE 1281
ABC 
						

							Navigation operation
42
Updating software
Each navigation CD you use has its own software 
included and the navigation unit reads and 
downloads that software whenever you insert a 
different CD.
When a different CD is inserted into the unit you 
will be prompted to select EXECUTE UPDATE 
using the right rotary control and press to 
confirm.
The system now checks radio and navigation 
software and loads all data required for further 
navigation. The display will show a progress bar. 
After a short delay the system restarts the 
navigation software and you will need to confirm 
the warning message.
Entering the location
The last location entered is displayed. If you want 
to enter a destination in the displayed location, 
you can select STREET or CENTER immediately. 
If your destination lies in another location, select 
the location using the right rotary control and 
press to confIrm.
Select the letters one after the other by turning 
the right rotary control and press to confirm.
The enlarged selected letter appears at the right 
of the display.
Using the multifunction button   the last 
confirmed letter is deleted. 
The complete entry is deleted if the multifunction 
button   is pressed for more than 2 seconds.NAVIGATION SYSTEM
TPRadNavCD
ICE 1282
NAVIGATION SYSTEM
TPCDRadNav
ICE 1211
NAVIGATION SYSTEM
TPCDRadNav
ICE 1212 
						

							43
Navigation operation
Letters which are already entered are displayed 
inversely. The unit offers only the possible 
remaining letters for selection. If no other entries 
are available, the unit completes the place-name 
automatically.
To accept the entry, press and hold the right 
rotary control for more than 2 seconds or select 
the small tick and briefly press the right rotary 
control.
If the complete place-name was previously 
entered or was automatically completed, the 
program switches to either place-distinguishing 
list or to street or center entry. 
In a situation where the entry name is linked to 
various locations throughout the country, a sub 
menu will display these locations with state and 
county details. Use the rotary control to select 
the desired location. The program will switch to 
either a place distinguishing list or to street or 
center entry.
If no streets and only the center can be selected 
in the location entered, the program switches 
directly to route menu. 
If an incomplete location entry was confIrmed, 
the place selection list is displayed.The place nearest to the entry appears in capital 
letters in the place selection list.
The scroll marks indicate that more places are 
available for selection in alphabetical order.
Select by turning and confirm by pressing the 
right rotary control.
If the entry is unequivocal, the program switches 
to street or center entry. If no streets and only the 
center can be selected in the location entered, the 
program switches directly to route menu
The place-distinguishing list is displayed if the 
selection is ambiguous.
Select the required place using the right rotary 
control and press to confirm.
The program switches to street or center entry
If no streets and only the center can be selected 
in the location entered, the program switches 
directly to route menu.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0290
NAVIGATION SYSTEM
TPCDRadNav
ICE 0292
NAVIGATION SYSTEM
TPCDRadNav
ICE 0292 
						

							Navigation operation
44
Entering a street name
Using the right rotary control, select STREET and 
press to confirm. At this point one of two 
methods can be used to find a street.
1.Select the first 2 or 3 letters of the street 
name, one after the other, by turning the 
right rotary control and pressing to confirm. 
When confirming the second or third letter, 
press and hold the control for more than 2 
seconds. An alphabetical street list is 
displayed. Scroll the list to find the desired 
street name and then press to confirm 
selection.
2.Select the letters one after the other by 
turning the right rotary control and press to 
confirm. The enlarged selected letter 
appears at the right of the display. Using the 
multifunction button   the last confirmed 
letter is deleted. The complete entry is 
deleted if the multifunction button   is 
pressed for more than 2 seconds.Letters which are already entered are displayed 
inversely. The unit offers only the possible 
remaining letters for selection. 
If no other entries are available, the unit 
completes the street name.
To accept the entry, press and hold the right 
rotary control for more than 2 seconds or select 
the small tick and briefly press the right rotary 
control. 
If the complete street-name was previously 
entered or was automatically completed, the 
program switches to either street-distinguishing 
list or to route menu.
If an incomplete location entry was confirmed, 
the street selectIon list is displayed.
NOTE: Street names with added direction 
information, eg. South Ford Street, are changed 
in the database to the streetname and a suffix so 
South Ford Street is dispalyed as Ford St S.If a 
search for ‘Ford’ reveals more than one Ford 
Street, each entry is displayed with a directional 
suffix like ‘Ford St N, Ford St S’ etc.
NAVIGATION SYSTEM
TPCDRadNav
ICE 1213
NAVIGATION SYSTEM
TPCDRadNav
ICE 1214
NAVIGATION SYSTEM
TPCDRadNav
ICE 1215 
						

							45
Navigation operation
The street nearest to the entry appears in capital 
letters in the street selection list. 
The scroll marks indicate that more streets are 
available for selection in alphabetical order. 
Select the street by turning the right rotary 
control and press to confirm.
If the entry is unequivocal, the program switches 
to route menu.
The street distinguishing list is displayed if the 
selection is ambiguous.
Select the required place using the right rotary 
control and press to confirm.
The program switches to route menu. 
Entering the destination center
Using the right rotary control, select center and 
press to confirm.
If the place selected only has one center, the 
program switches immediately to route menu. 
If the number of centers is less than 10, the 
center list is displayed.
Select the center by turnIng the rIght rotary 
control and press to confirm.
If the number of centers is greater than 9, the 
programme switches to center entry.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0296
NAVIGATION SYSTEM
TPCDRadNav
ICE 0297
NAVIGATION SYSTEM
TPCDRadNav
ICE 1216
NAVIGATION SYSTEM
TPCDRadNav
ICE 0299 
						

							Navigation operation
46
Select the letters one after the other by turning 
the right rotary control and press to confirm. The 
enlarged selected letter appears at the right of the 
display. 
Using the multifunction button   the last 
confirmed letter is deleted.
The complete entry is deleted if the multifunction 
button   is pressed for more than 2 seconds.
Letters which are already entered are displayed 
inversely. The unit offers only the possible 
remaining letters for selection. If no other entries 
are available, the unit completes the 
center-name.
To accept the entry, press and hold the right 
rotary control for more than 2 seconds or select 
the small tick and briefly press the right rotary 
control. If the complete center-name was previously 
entered or was automatically completed, the 
program switches to route menu.
The program switches to the center list if the 
selection is ambiguous. 
The center nearest to the entry appears in capital 
letters in the center list. 
The scroll mark indicates that more centers are 
available for selection in alphabetical order. 
Select the center by turning the right rotary 
control and press to confIrm.
The program switches to the route menu. 
NOTE: A list of possible centers is displayed 
immediately pressing the right rotary control for 
more than 2 seconds without having selected 
any letters. 
NAVIGATION SYSTEM
TPCDRadNav
ICE 1217
NAVIGATION SYSTEM
TPCDRadNav
ICE 1218
NAVIGATION SYSTEM
TPCDRadNav
ICE 0302 
						

							47
Navigation operation
ROUTE MENU
Selection from
•SAVE DESTINATION
•START-FAST R., START-SHORT R.
•HOUSE NUMBER
•CROSSING
•ROUTE SETTING
can be made by turning, and confirmed by 
pressing the right rotary control.
•SAVE DESTINATION
accesses the entry menu for the destination 
memory.
•START-FAST R., START-SHORT R. 
starts route guidance. Simultaneously, a 
prompt appears indicating the currently 
selected route option (-SHORT R. for a short 
route, -FAST R. for a fast route).
•HOUSE NUMBER
The house number In the specIfied 
destinatIon road can be entered here. 
This function is only available if this 
information is stored on the navigation CD.
•CROSSING
An intersecting road can be defined as the 
destination here. 
This function is only available if this 
information is stored on the navigation CD.
•ROUTE SETTINGS
Specifications such as FAST route, short 
route, motorway, ferries and toll roads can be 
selected here.
Entering the house number for the 
destination street
Using the right rotary control select HOUSE 
NUMBER in the route menu and press to 
confirm.
Using the right rotary control, enter the house 
number for the destination street and press for 
more than 2 seconds to confirm the entry. To 
confirm, the small tick can also be selected and 
the right rotary control briefly pressed. Due to the 
system characteristics, route guidance continues 
only in the area of the house number specified.
Select START- to start route guidance. 
Select SAVE DESTINATION to jump to the 
destination memory menu.
Select ROUTE SETTINGS to access the possible 
route settings. 
Select by turning the right rotary control and 
press to confIrm the selection
NAVIGATION SYSTEM
TPCDRadNav
ICE 0303
NAVIGATION SYSTEM
TPCDRadNav
ICE 0304
NAVIGATION SYSTEM
TPCDRadNav
ICE 0305 
						

							Navigation operation
48
Select the intersection for the destination 
street
Using the right rotary control, select CROSSING 
in the route menu and press to confirm.
Select the intersection for the destination street 
by turning the right rotary control and press to 
confirm the selection.
Select START- to start route guidance.
Select SAVE DESTINATION to jump to the 
destination memory menu. 
Select ROUTE SETTINGS to access the possible 
route settings.
Select by turning the right rotary control and 
press to confirm the selection.
Selecting the route settings
Using the right rotary control, select ROUTE 
SETTINGS in the route menu and press to 
confirm.
•FAST ROUTE (WITH HIGHWAY)
If selected, the programme calculates the 
shortest possible journey time.
•FAST ROUTE (WITHOUT HIGHWAY)
Fastest route without using a highway.
•SHORT ROUTE (WITH HIGHWAY)
If selected, the programme calculates the 
shortest possible distance and may use 
highway as short route.
•SHORT ROUTE (WITHOUT HIGHWAY)
May use single track roads so caution is 
needed when towing a large trailer.
NOTE: The setting “SHORT ROUTE” is often 
recommended for larger cities or conurbations.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0306
NAVIGATION SYSTEM
TPCDRadNav
ICE 0305
NAVIGATION SYSTEM
TPCDRadNav
ICE 0307 
						

							49
Navigation operation
•RESTRICTIONS
Provides options for avoiding highways, 
ferries or toll roads.
Selection can be made by turning the right rotary 
control, and settings can be changed by pressing 
the right rotary control.
Press the control for more than 2 seconds to 
accept all settings and quit the menu.
NOTE: Routes without highways can only be 
calculated for short distances (up to 120 miles).
NOTE: It is possible that routes without the use 
of interstate highways may not be calculable. In 
this case you will receive a message
NAVIGATION SYSTEM
TPCDRadNav
ICE 1219