Land Rover Audio Navigation System Nas Rover Manual

							Navigation operation
50
Storing a specified destination in the 
destination memory
It is not absolutely necessary to store a 
destination in the destination memory for route 
guidance. It saves repeated manual entry, if the 
destination is required at a later date.
Select SAVE DESTINATION in the route menu 
and press the right rotary control to confirm.
Any name of your choice consisting of up to 14 
characters can be entered for the specified 
destination and then automatically only be stored 
in the destination memory after pressing the 
right rotary control for more than 2 seconds.
To store, the small tick can also be selected and 
the right rotary control briefly pressed. If you do 
not wish to enter a name of your choice, press 
and hold the right rotary control for more than 2 
seconds to store the address as previously 
entered in the destination memory.
The last destination entered can be filed at any 
position by turning the right rotary control. The 
memory position is confirmed by briefly pressing 
the right rotary control. 
A total of 50 destinations can be stored. 
NOTE: Do not save your home address as 
‘HOME’. Should your vehicle be stolen with your 
keys, for example, the thief could easily find your 
home address and be guided there by your 
navigation system.For final storage in the destination memory, 
either route guidance must be started or the 
program must be switched to a new destination 
entry by selection of NEW DEST.
Deleting stored destinations
Select destination memory.
Select the destination to be deleted using the 
right rotary control and press the ‘Del’ 
multifunction button.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0309
NAVIGATION SYSTEM
TPCDRadNav
ICE 0310
NAVIGATION SYSTEM
TPCDRadNav
ICE 0311 
						

							51
Navigation operation
Destination memory full
This occurs when the destination memory is full.
Select either DELETE (to jump to the destination 
memory in order to delete a destination) or BACK 
(to cancel saving). 
ROUTE GUIDANCE CALCULATION
The message “Calculating route” indicates that 
the distance is being calculated, which may take 
several seconds. 
After the first route guidance announcement, the 
prompt CD flashes on the display until the route 
has been completely calculated. When entering a 
destination, driving off should be delayed until 
CD no longer flashes.
Recalculating the route
If the current route is not followed due to road 
blocks, diversions, unintentional driving in the 
wrong direction or failing to observe the 
recommendations, the system immediately 
calculates a new route. During this recalculation, 
NEW ROUTE is displayed. 
STOPOVER
This function enables a stopover to be entered 
when route guidance is active.
Entering a stopover
Press the multifunction button  .
NAVIGATION SYSTEM
TPCDRadNav
ICE 0312
NAVIGATION SYSTEM
TPCDRadNav
ICE 1260
NAVIGATION SYSTEM
TPCDRadNav
ICE 1261
NAVIGATION SYSTEM
TPCDRadNav
ICE 1262 
						

							Navigation operation
52
Using the right rotary control, make a selection 
and press to confirm.
•DEST. MEMORY
select the stopover from the destInatIon 
memory.
•DESTINATION
enables the selection of special destinations 
as stopovers via NEARBY DESTINATION, 
NEARBY and TOWN, e.g.gas stations or 
airports.
Starting route guidance to a stopover
To start route guidance to the stopover, press the 
right rotary control.
The route is calculated and route guidance 
begins.
NOTE: The   symbol is displayed inversely 
during route guidance to a stopover. 
Deleting a stopover
Press the multifunction button  .
NAVIGATION SYSTEM
TPCDRadNav
ICE 0316
NAVIGATION SYSTEM
TPCDRadNav
ICE 0317
NAVIGATION SYSTEM
TPCDRadNav
ICE 1263 
						

							53
Navigation operation
To delete the stopover, press the right rotary 
control within 8 seconds. 
Stopover reached
Route guidance to the final destination 
automatically starts following the message “YOU 
HAVE REACHED YOUR STOPOVER”
TRAFFIC JAM FUNCTION
This function allows you to block the 
approaching route sections as from the next 
junction and calculate a bypass route when a 
traffic jam or road block is directly ahead.
Entering the length of a traffic jam
Press the multifunction button  .
Using the right rotary control, select the length of 
the traffic jam and press to confirm.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0319
NAVIGATION SYSTEM
TPCDRadNav
ICE 0320
NAVIGATION SYSTEM
TPCDRadNav
ICE 1264
NAVIGATION SYSTEM
TPCDRadNav
ICE 0322 
						

							Navigation operation
54
 is displayed inversely and the route is 
recalculated.
Delete block
Press the multifunction button 
To delete a block, press the right rotary control 
within 8 seconds.
CANCELLING ROUTE GUIDANCE
Press the ‘Nav’ button
Route guidance is cancelled by pressing the right 
rotary control within 8 seconds, otherwise, route 
guidance continues.
NOTES ON ROUTE GUIDANCE
After entering the destination (address), the 
system calculates the route and announces: “We 
can start now”. 
The driving recommendations are given by voice 
messages and displays on the screen.
By pressIng the left rotary control the current 
drivIng recommendation can be repeated.
If the route to be travelled is not clear, e.g. at an 
intersection where a change in direction is not 
specified, the direction of travel can be displayed 
by pressing the right rotary control.
Please follow the direction indicated by the 
arrow. 
NAVIGATION SYSTEM
TPCDRadNav
ICE 1265
NAVIGATION SYSTEM
TPCDRadNav
ICE 1266
NAVIGATION SYSTEM
TPCDRadNav
ICE 0325
NAVIGATION SYSTEM
TPCDRadNav
ICE 0326
NAVIGATION SYSTEM
TPCDRadNav
ICE 1267 
						

							55
Navigation operation
The display appears for 8 seconds after pressing 
the right rotary control.
Danger! If a driving recommendation 
contradicts the applicable Road Traffic 
Regulations (RTR), the RTR is always valid!
For clarification, there follows a selection of 
examples of possible driving recommendations:
•“Please perform a U-turn if possible”.
You are driving In the wrong dIrectIon and 
should turn back at the earlIest opportunIty.
•Please turn right after 1/4 mile”. 
The arrow indicator   points to the next street 
into which you should turn. The name of the 
street is displayed.
The progress bar on the right illustrates the 
distance and the black part decreases as you 
approach the intersection.•“Please follow the road”.
This display tells you that you should follow the 
course of the road.
•“Prepare to turn left” or “Please move into the 
left-hand lane”.
This recommendation prepares you for the next 
turning to be taken
However, “move into the left-hand lane” does not 
mean that you should do so immediately!
NOTE: At junctions and traffic circles, only the 
end of the street which is to be passed is 
displayed.
NAVIGATION SYSTEM
TPCDRadNav
ICE 1220
NAVIGATION SYSTEM
TPCDRadNav
ICE 1268
NAVIGATION SYSTEM
TPCDRadNav
ICE 1269
NAVIGATION SYSTEM
TPCDRadNav
ICE 1270 
						

							Navigation operation
56
•“Please leave the traffic circle at the third exit 
on the right”.
This display shows you which exit (marked with 
the arrow) you must take at the traffic circle.
•“Now drive straight ahead”
At this point, you must drive straight ahead. •“Please follow the directIon arrows”.
This display tells you that you are in a 
non-digitised street (e.g. car park, garage), 
which is not included in the digital street map. 
The arrow indicates the direction of the 
destination as the crow flies.
•“Keep right after 2 miles”. 
Keeping to the right means that the road forks 
and you should follow the relevant direction. 
NAVIGATION SYSTEM
TPCDRadNav
ICE 1221
NAVIGATION SYSTEM
TPCDRadNav
ICE 1271
NAVIGATION SYSTEM
TPCDRadNav
ICE 1272
NAVIGATION SYSTEM
TPCDRadNav
ICE 1273 
						

							57
Navigation operation
•“You have reached your destination”. 
The destination specified is reached and route 
guidance is terminated.INFORMATION DURING ROUTE GUIDANCE
Press the left rotary control.
The destination, the distance and the estimated 
time of arrival are dIsplayed.
If a stopover has been specified, the stopover, 
the distance and estImated tIme of arrival are 
displayed.
The main destination can be displayed via the 
multifunction button  .
Press the multifunction button on the far left to 
display;
Time travelled
Average speed
Distance travelled
To return to route guidance, press the left rotary 
control again or wait for 8 seconds.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0336
NAVIGATION SYSTEM
TPCDRadNav
ICE 0337
NAVIGATION SYSTEM
TPCDRadNav
ICE 0338 
						

							Navigation operation
58
Requesting journey duration and distance 
travelled
During route guidance, press the left rotary 
control.
Press the multifunction button  .
The journey duration, distance travelled and the 
average speed are displayed. Pressing the right 
rotary control or the ‘Nav’ button, returns to the 
route guidance display.
The information for journey duration, distance 
travelled and the average speed can be requested 
as previously described, provided that the 
destination flag waves after the destination has 
been reached.
NOTE:  The destination flag graphic is only active 
if ANIMATIONS are turned on. See SYSTEM 
SETTINGS - Animations.
Displaying the route settings
During route guidance, press the left rotary 
control. Press the ‘Mod’ multifunction button.
The route settings are displayed.
After 8 seconds, the system returns to the route 
guidance display.
NAVIGATION SYSTEM
TPCDRadNav
ICE 0926
NAVIGATION SYSTEM
TPCDRadNav
ICE 1222
NAVIGATION SYSTEM
TPCDRadNav
ICE 0339
NAVIGATION SYSTEM
TPCDRadNav
ICE 0340 
						

							59
Navigation operation
Requesting current time
During route guidance, press the left rotary 
control. Press the   multifunction button.
The current time is displayed. After 8 seconds, 
the system returns to the route guidance display.
Requesting current position
During route guidance, the current position can 
be requested.
Press the multifunction button  .The current position with road name 
(if available), degrees of longitude and latitude 
and the number of satellites received are 
displayed. 
By pressing the right rotary control, the program 
returns to the route guidance display
The current position can be requested even when 
route guidance is not active by pressing the left 
rotary control.
Press the multifunction button  .
NAVIGATION SYSTEM
TPCDRadNav
ICE 0341
NAVIGATION SYSTEM
TPCDRadNav
ICE 0342
NAVIGATION SYSTEM
TPCDRadNav
ICE 0343
NAVIGATION SYSTEM
TPCDRadNav
ICE 0344
NAVIGATION SYSTEM
TPCDRadNav
ICE 0928