Lawn Mower 8211-7060-10 85 Combi, 95 Combi, 105 Combi For Mountfield 2000 And 4000 Series Instruction Manual

85 Combi, 95 Combi, 105 Combi for
8211-7060-10
INSTRUCTIONS FOR USE
MODE D’EMPLOI
GEBRUIKSAANWIJZING
GEBRAUCHSANWEISUNG
ИНСТРУКЦИЯ ПОЛЬЗОВАТЕЛЯEN .... 5
FR... 10
NL ... 15
DE .. 20
RU .. 25
Mountfield 2000 and 4000 series 

2
125 Combi Pro
2000-series, 4000-series 4WD
ABC(D)
90°
A
B C
4000-series 2WD
GF E
PP Q
Q
45 Nm
R
3
5 
71
4
6 
82 

3
4000-series 4WD
2000-series
16”
4000-series 2WD
17”
11
13
159 
12
14
1610  

4
1/3
19
 
 17
20
  18  

5
ENGLISHEN
1 GENERAL
This symbol indicates WARNING. Seri-
ous personal injury and/or damage to 
property may result if the instructions 
are not followed carefully.
You must read these instructions for use 
and the machine’s safety instructions 
carefully.
1.1 SYMBOLS
The following symbols appear on the machine. 
They are there to remind you of the care and atten-
tion required in use.
This is what the symbols mean:
Warning!
Read the instruction manual and the safety 
manual before using the machine....

6
ENGLISHEN
3 ASSEMBLY
3.1 MACHINES WITH FIXED DECK 
CONNECTIONS
Example of fixed deck connections, see 3:C and 
4:G.
1. Place the deck in position in front of the ma-
chine.
2. Check that the deck mounts are installed on the 
machine as follows.
4000-series 2WD
:
• Deck mount (4:G).
• Washer (4:F).
• Lock pin (4:E).
4000-series 4WD, 2000-series
:
• Washer (3:D). Only machines up to and in-
cluding 2006.
• Deck mount (3:C).
• Washer (3:B).
• Circlip (3:A).
3. Remove pins and washer (2:C, 2:D).
4. Screw...

7
ENGLISHEN
4 USING THE MACHINE
Check that the grass that is to be cut is 
completely free of foreign objects such 
as stones etc.
4.1 CUTTING HEIGHT
The best cutting results are achieved when the 
when the top third of the grass is cut off. I.e. 2/3 of 
the length of the grass remains. See fig. 14.
If the grass is long and has to be cut significantly, 
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn 
surface is uneven. This would entail a risk of the 
blades...

8
ENGLISHEN
5. Release the belt tension as follows:
4000-series 2WD
:
Remove the tensioner from the belt. See fig. 10.
4000-series 4WD
:
Grip the belt tensioner’s lever with your left 
hand. Pull the lever and remove the tensioner 
with your right hand. See fig. 9.
2000-series
:
Remove the tensioner from the belt. See fig. 11.
6. Force the belt off the machines’s pulley.
7. Grip the front edge of the deck and lift up. Lift 
until the deck is completely vertical and rest the 
rear edge on the ground. See...

9
ENGLISHEN
5.5.3 Synchronising, blades
The deck has synchronised blades.
If one of the blades has struck a solid object (e.g. a 
stone), the synchronisation may be altered. This 
entails a risk of the blades colliding with each oth-
er.
Correctly synchronised blades must be offset 90° 
from each other. See fig. 7.
Always check synchronisation after a collision.
If the blades are not synchronised, one or more of 
the following faults may have occurred in the cut-
ting deck:
• The positive drive belt has...

10
FRANÇAISFR
1 GÉNÉRALITÉS
Ce symbole est un AVERTISSEMENT. 
Risque de blessure ou de dégât matériel 
en cas de non-respect des instructions.
Lire attentivement les instructions et les 
consignes de sécurité avant d’utiliser la 
machine.
1.1 SYMBOLES
Les symboles suivants figurent sur la machine. Ils 
attirent votre attention sur les dangers d’utilisation 
et les mesures à respecter.
Explication des symboles:
Attention! 
Lire le mode d’emploi et le manuel de sé-
curité avant d’utiliser la machine....