Lawn Mower 8211-7060-90 85 Combi, 95 Combi, 105 Combi For Mountfield 2000 And 4000 Series Instruction Manual

INSTRUCTIONS FOR USE
85 Combi, 95 Combi, 105 Combi for
8211-7060-90
INSTRUCTIONS FOR USE
GEBRUIKSAANWIJZING
MODE D’EMPLOIEN..... 5
NL... 10
FR.... 15
 Mountfield 2000 and 4000 series 

2
125 Combi Pro
4000-series 4WD, 2000-series
ABC(D)
K K2000-series
A
B C
4000-series 2WD
GF E
I
H
K
4000-series 4WD
K
3
5 
71
4
6 
82 

3
4000-series 4WD
2000-series
16”
4000-series 2WD
11
13
159 
12
14
1610  

4
1/3
PP Q
Q
45 Nm
R90°
19
 21
 2317
20
22
  18  

5
ENGLISHEN
1 GENERAL
This symbol indicates WARNING. Seri-
ous personal injury and/or damage to 
property may result if the instructions 
are not followed carefully.
You must read these instructions for use 
and the machine’s safety instructions 
carefully.
1.1 SymbolsThe following symbols appear on the machine. 
They are there to remind you of the care and atten-
tion required in use.
This is what the symbols mean:
Warning!
Read the instruction manual and the safety 
manual before using the machine....

6
ENGLISHEN
3 ASSEMBLY
3.1 4000-series 4WD with fixed deck 
connections and 2000-series
Example of fixed deck connections, see 3:C and 
4:G.
1. Place the deck in position in front of the ma-
chine.
2. Check that the deck mounts are installed on the 
machine as follows.
• Washer (3:D). Only machines up to and in-
cluding 2006.
• Deck mount (3:C).
• Washer (3:B).
• Circlip (3:A).
3. Screw the arms into each other. See fig. 5.
4. Remove the belt cover (6:H) by loosening the 
screws 6:I. 
5. Loosen the belt...

7
ENGLISHEN
3.4 Tyre pressureAdjust the tyre pressures according to the table be-
low.
3.5 Basic settingIn order for the cutting deck to cut optimally, the 
correct basic setting is required. The deck is in the 
basic setting when its rear edge is 5 mm above its 
front edge. This means that the deck is inclined 
forwards.
Move the deck to the basic setting by lifting and 
securing as follows.
Install the washers and the pins in the middle hole. 
See fig. 15.
4 USING THE MACHINE
Check that the grass that...

8
ENGLISHEN
6. Lower the deck to the ground in reverse order 
after the corrective actions have been carried 
out. Reset the deck according to “3”.
5.3 Service position
5.3.1 4000-series 4WD with fixed deck 
connections and 2000-series
1. Activate the parking brake.
2. Set the maximum cutting height.
3. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine. 
See fig. 13.
4. See fig. 2. Detach the rear section of the deck on 
the right and left-hand side as...

9
ENGLISHEN
5.4 CleaningThe underside of the deck must be cleaned after 
each use. 
Set the deck in washing position. 
Clean the underside of the deck carefully. Use wa-
ter and a brush.
When the surfaces are completely dry and clean, 
touch up the paintwork. Use durable yellow paint 
intended for metal outdoors.
5.5 Blades
5.5.1 Safety
To reduce the risk of accidental injury in the event 
of a collision and to protect important parts in the 
cutting deck, a force limiter is integrated as fol-
lows.
•...

10
NEDERLANDSNL
1 ALGEMEEN
Dit symbool geeft een WAARSCHU-
WING weer. Als de instructies niet nau-
wkeurig worden opgevolgd, kan dit 
leiden tot ernstige persoonlijke verwon-
dingen en/of schade.
Lees de gebruikershandleiding en de 
veiligheidsinstructies voor gebruik 
goed door.
1.1 SymbolenOp de machine ziet u de volgende symbolen om u 
eraan te herinneren dat voorzichtigheid en oplet-
tendheid bij gebruik geboden is.
Betekenis van de symbolen:
Waarschuwing!
Lees vóór gebruik van de machine de ge-...